Devanco Canada - Get The Right Garage Door Opener‎ and Parts

65-32449

LiftMaster Thermostat Control Heater 115V & 575V Fin Type ** Discontinued

Designed to automatically maintain a suitable temperature inside a control enclosure down to -40 degrees F.
Uses a high surface area aluminum heat emitter to eliminate the need for a fan
Provides low-radiation and high-convection heating in the enclosure
Adjustable from 30 degrees to 120 degrees F. (0 to 50 degrees C.) 208V - 460V
Compatible with operators SL575 SL585 and SL595

2650-112-05

Linear Cold Weather Package 230V SLC gate Op. Only

Cold weather package includes: Arctic oil Heater Cogged V-belt

2650-112-06

Linear Cold Weather Package 230V SLR gate Op. Only

Cold weather package includes: Arctic oil Heater Cogged V-belt

SLR-221

Linear Residential Slide Gate Op. 1/2HP 230V 1 Ph - Cold Weather Package NOT Included

Integral entrapment sensing system with digital set point for quick accurate adjustment and enhanced safety
Continuous-tone entrapment alarm with reset button
LED diagnostic display for ease of setup and troubleshooting
Selectable pre-start and run alarm with provision for ADA compliant visual pre-start and run alarm
Regulated 24 Volt DC power available for access control accessories
Integrated maximum run and auto close timer (0-9 minutes)

.......more details

7001-8-CHARCOAL

Commercial Side & Top Weather-Strip 8' Long - Charcoal (H)

Charcoal galvanized steel with charcoal dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

LVB1020-11

Laminated Bumper Black 10" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

37313

Doorlec Relay Flat Pins 2 Pole 24V

37314

Doorlec Relay Mini 120V

For overrun pre-wired 25 Amp

MK00661

Micanan Varistor for Circuit Board 110V *** NLA Use MK00707

COOKSON-45-GREY

Rolling Steel Slat 3" Cookson Insulated with Wind Locks

Special order

1104-16'-LT-BNZ

Residential Side & Top PVC Weather-Strip with cap 16' Long - Light Bronze (F) **NLA

Light bronze rigid vinyl retainer with light bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

07-8058

LiftMaster Crank Link BG790

PRO-H-7511U-RH

Micanan 3/4HP 115V 1P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

Installation manual Specification sheet

5001-WG-18-MOAK

Residential Side & Top Weather-Strip 18' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Special order
Sold by full case quantity (20)

.......more details

5001-WG-16-MOAK

Residential Side & Top Weather-Strip 16' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Sold by full case quantity (20)

5001-WG-10-MOAK

Residential Side & Top Weather-Strip 10' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Sold by full case quantity (20)

5001-WG-8-MOAK

Residential Side & Top Weather-Strip 8' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Sold by full case quantity (20)

5001-WG-7-MOAK

Residential Side & Top Weather-Strip 7' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Sold by full case quantity (20)

1104-12FT-BRONZ

Residential Side & Top PVC Weather-Strip with cap 12' Long - Bronze (F)

Bronze rigid vinyl retainer with bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

1104-10FT-BRONZ

Residential Side & Top PVC Weather-Strip with cap 10' Long - Bronze (F)

Bronze rigid vinyl retainer with bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

1104-9FT-BRONZE

Residential Side & Top PVC Weather-Strip with cap 9' Long - Bronze (F)

Bronze rigid vinyl retainer with bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

GL-12-LED

Guide Lights for Loading Docks Amber LED 12-24VAC/DC 13.5" long Sold as a Pair *Discontinued*

LED lights offer long-lasting reliable high-visibility in all weather conditions including direct sunlight with low power consumption.
Robust housing resists impact and corrosion.
Slim discrete design ensures little risk of damage due to accidental impact.
Wide input voltage range of 12-24Vac/dc (control box available for alternate voltages).
Boards coated in water-resistant polymer for optimal protection from water and humidity.
12 LEDs per guide light

.......more details

28-03190

Truck Door 1" Vert. Track and Right Angle Assbly Roadside (LH) 96.5" Todco Style***To extent of inventory

For Todco style doors
Galvanized steel 14-gauge construction
Includes right angle frame 1" track and operator bracket
Fits doors 72" - 90" high

PPLV1

LiftMaster Passport Lite 1-Button Visor Remote with Sec+ 2.0 Technology

Passport Lite Remote Controls provide cost-effective single button access solutions for gate access only or high-capacity commercial properties applications such as employee parking lots and tenant garages.
These remote controls are specifically designed for gate access control and are not compatible with LiftMaster Garage Door Openers.
2x the range of standard remote controls
Narrow-band transmission on 3 simultaneous frequencies (310 MHz 315 MHz 390 MHz)
Compatible with LiftMaster® commercial receivers (850LM 860LM PPWR STAR1000) and Security+ 2.0™ Gate Operators
Block coded

.......more details

Programming instructions Instructions de programmation Sell sheet Brochure

MOUNTSHAFT016

Manaras Clutch & Hoist Shaft Kit for Opera-SH

Input / clutch shaft kit for Manaras Opera-SH

SF514U

Spring Fitting 5-1/4" Pair for 1" shaft

Universal thread for use in either LH or RH wound springs.
Pair includes: (1) winding & (1) stationary.

201-300-301-00

Equinoxe Long Range Transmitter O/C/S for 1-Door 433 MHz. Pre-2016

Open/Close/Stop remote for 1 door
Range of approx. 1000ft
A heavy-duty remote for Industrial applications
Old generation - prior to 2016

Programming Instructions Instructions de programmation

ACT-34D

Linear 4-Channel Block Coded MegaCode Key Ring Trans Prox Transmitter 318 MHz

Compatible with all Linear access receivers and controllers
Built-in 26-bit Wiegand proximity tag
Eliminates need for separate proximity card or tags and transmitter
Supplied with quick-disconnect key ring
Same facility and ID codes for transmitter and proximity tag
Sold in lots of 10

.......more details

PRO-HBH-10023U-R

Micanan 1 HP 230V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand (Pro-HHD)

1 HP230V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

BK020/PR-BOLT

Commercial 2" Safety Bottom Bracket with Bolt Sold as a Pair

Maximum cable diameter: 3/16"
Maximum door weight: 1300 lbs Zinc
Plated Steel
Sold as a pair

Installation manual

20-8100M-DC

LiftMaster Electric Motor for VSL 1 HP 90 VDC 1 ph

Replacement electric motor for VSL gate op.

IRB-RX

EMX Industries Receiver Board Only for IRB-4X *** NLA

12575

Doorlec Clutch Disc Fiber 4" dia.x 5/8" bore

Fits model LJ / LJH

CB116A0500

Cable 1/16" 7x7 500' Galvanized

Galvanized cable 1/16" 7x7 500ft spool.

3-26-1

Half Hinge Type S Service Type Door ** Available to Extent of Inventory

Half hinge type "S"
16-gauge

37516S

Genie Belt only for 8ft Door

Replacement belt only for 8ft door
Fits Genie model Destiny 1200

41A6569

LiftMaster Safety Sensor Mounting Kit

Replacement brackets only for 41A4373A safety eyes

TUBE_SHAFT_12FT

Hollow Shaft 1" x 12'-10" Galvanized 16 gauge

When ordering order one foot longer that actual door width

NUT022

Manaras Lock Nut Zinc Plated 3/8-16 Hex Nylon

Used on old MJH

NIR-HD

EMX Industries NIR Hood Cover Steel

The hood keeps rain and other debris from distorting or blocking the photo beam.
It also helps to keep the sun from glaring off the reflector and disturbing the beam's reflection.
Replaces the mounting bracket that comes with the sensor.
Comes with Hood two sets of nuts and bolts and a plug

4X20PO50

Devanco Loop 4' x 20' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

1003-4-DF-CUT

Bottom U-Rubber 4" Dual Fin Black Sold per Foot

Sold in cut lengths per foot.
Dual fin

1003-3-DF-CUT

Bottom U-Rubber 3" Dual Fin Black Sold per Foot

Sold in cut-lengths per foot.
Dual fin

C20-32F

Bearing 1-1/4" x 2" Press Fit C20-32F+GR 400 LBS

Stamped bearing for lighter loads
For a heavier duty machined bearing use R5114

28020020-500

Cable Stainless 5/16" 1x19 500' Inox ** Price on Request

Not for use in aircraft applications
1x19 contruction type 302 / 304

Comparison charts

H12G10-SS

Hinge #10 x 12 gauge Stainless Steel

Manufactured with 12ga. Rust-Resistant Stainless Steel
Universal Design
Fits Most Overhead Sectional Doors
Priced Per Each

82-SB50-08

LiftMaster Shoulder Bolt 3/8"-16x8 **DISCONTINUED

Shoulder Bolt
For SW470-S3
Formerly 82SB5008 G82SB5008

80-2103

LiftMaster Tinnerman Nut **DISCONTINUED

Black Plastic Knob
Formerly 802103 G802103
For SW470 with GL or S3 Board

ME123-M-YEL-RH

Miller Edge Yellow RH 4-Wire Monitored 2" wide x 1-1/2" high Sold by the Foot

Electromechanical slide in edge for sectional doors and sliding gates.
Touch sensitive singaling allows for immediate stopping and reversing of motion
Temperature range: -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Worksheet Installation manual Sell sheet

26CW94325-CUT

Truck Door Bottom Panel with Seal (15" x Cut-To-Size Painted White for Whiting Dryfreight

These panels are cut to customer's specifications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes only with bottom retainer and seal (installed)

.......more details

CHI-SPECIAL

C.H.I. Special Order Door

Special order as per customer's requirements

50180

Doorlec Brake Assembly 120V

20109

Doorlec Hoist Spring EHJ

745266

Strobe Low Profile Amber LED Warning Light 12-24VDC

Fully encapsulated electronic circuitry ensures a lifetime of trouble-free operation.
Installer can select the flash pattern of each high intensity strobe by wiring the unit according to the flash rate preferred.
4 7/8" X 5 7/8" Rubber base Surface mount 12-24VDC

MGS20-B-2L-05

Miller Edge Sensing Edge Square Black 2-Wire Left Hand Outlet 5ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

MGS20-Y-2L-05

Miller Edge Sensing Edge Square Yellow 2-Wire Left Hand Outlet 5ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

CABLE_1/8SS5000

Cable 1/8" 7x19 5000' Stainless Steel ** Price on request

9291644400

Galvanized Torsion Spring .306 x 3-3/4 x 44" L with Cones LHW

9301644400

Galvanized Torsion Spring .306 x 3-3/4 x 44" L with Cones RHW

MD00044

Micanan Spur Gear 12B60

053156

Magnetic Mount Micro Dome Beacon Amber ** To Extent of Inventory

60 LEDs 360 degree revolving flash / intermittent flash
-30 degree celsius to + 50 degree celsius extreme temperature reliability

OSH-6213-ECB-LH

Manaras Opera-SH 3/4 HP 240V 1Ph with Electronic Circuit Board Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation manual Sell sheet

CONTACTOR003

Manaras Repl. Kit Reversing Contactor Allen Bradley 16A-24VAC

Drawing

K20-1050B2LPH24

LiftMaster Electric Motor 1/2 HP 115V 1Ph Logic 5

Standard 1/2 hp motor for new L5 operators

36764A

Genie Chain and Belt Pulley (#39591A)

Works on Genie IntelliG 1000 & 1200 Garage Door Openers
Both for Chain and Belt Openers
Front Idler Pulley for Genie 4024
New part number #39591A

OMJ-6112-ECB-L

Manaras Medium-Duty Jackshaft Operator 1/2 HP 120V with Electronic Circuit Board Left Hand

Designed for use on standard high and vertical lift sectional doors
Can also be used on small rolling doors and grills
Single phase intermittent-duty motor has instant reverse and internal automatic reset thermal overload protection
Mechanical brake
Floor level disconnect mechanism which must be engaged for manual push-up operation
14 cycles per hour 50 cycles per day

.......more details

Installation manual Sell sheet

8087.225.310

Whiting .225 x 2-5/8 IN x 31" Curbside with Cones

An original Whiting assembly

MC00012

Micanan Gear Reducer PRO-GOHD BHC 63 40:1 56C

VBELT_5L340

VBelt 5L 34"

Fits Lynx HDC operator

RA-AD-WKP-05

Lynx 5-btn Wireless Keypad AD455 372 MHz

Programming Instructions Compatibility chart

RA-AD-T3

Lynx 3-btn Transmitter AD455 372 MHz

UL325
Works on the new Lynx operators
For 3 doors

Programming Instructions Compatibility chart

1005-1-1/2-10'

Aluminum Bottom Retainer U-Shaped 10' Long

For door thickness 1-1/2"

MT-1B

Linear 1-btn MegaCode Block Coded Transmitter 318 MHz

Compatible with all Linear access receivers and controllers
Superior transmission range
Operate LED
Visor clip included
Sold in lots of 10
Power: 9-volt battery

.......more details

26966A

Genie Idler Pulley for Stealth Chain Drive

Fits Genie Stealth model
1/4” bore
Channel style rails

.250-334-R

Cut-to-Length Torsion Spring .250 x 3-3/4" Right Hand Wound Green

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

15-50B35QGH

Sprocket 50B35 1-1/4" Bore 1/4" Keyway

MX00145

Micanan Brake Assembly for PRO-APT Solenoid NOT included ** DISC

Discontinued. Use part number MX00140

PBS3-GREEN

Replacement Button Only - Green

Replacement button for 02-403P

PBS3-RED

Replacement Button Only - Red

Replacement button for 02-403P

MK-00011

Micanan Radio Control Terminal Strip

OPH-6113-CONT-L

Manaras Opera-H 3/4HP 120V 1Ph with Mechanical Contactor Left Hand

A heavy-duty industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a self-engaging chain hoist for manual operation
Clearence: side room required 15"

Installation Manual Sell Sheet

H105L5-LH

LiftMaster Ind. Duty Hoist Op. 1 HP 575 VAC 3 Ph Logic 5 Left Hand W/Brake

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details

Installation Manual Manuel d'installation Sell sheet Brochure

CABLE-NR-14-CC

Cable No Roll 1/4" 19x7 Non-Galvanized C-Coated 500ft

19X7 rotation-resistant wire rope.

11-10705

LiftMaster Output Shaft MH

.363-6-L

Cut-to-Length Torsion Spring .362 x 6" Left Hand Wound Green/White

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

OSH-6112-CONT-R

Manaras Opera-SH 1/2HP 120V 1Ph Contactor Right Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"

Installation Manual Sell Sheet

MOUNTSHAFT010

Manaras Hoist Shaft Kit for MJH (pre-1998)

Drawing

EQ2722

SkyLink 3/4 HP Garage Door Opener with 2 2-Btn Keychain Remotes ** Discontinued

The DC motor offers additional benefits with very quiet operation and much less vibration.
It is ideal for garage doors that are below a living room or bedroom.
The DC motor also offers the soft start soft stop features which reduces the vibration and wear and tear of all the mechanical parts
Features: Rolling Code Technology Soft Start Soft Stop Optimal Force Learnings and Safety Beam Sensors.
Available in either Belt or Chain drive
Includes two 2-btn keychain remotes # MK318-2

.......more details

Installation Manual Sell Sheet

K72-19975

LiftMaster Clutch Shaft and Sprocket Assembly

Assembly includes: Clutch shaft 1" keyed flange bearings Dual sprcket 32/14 Splined core sprocket E-ring Compression spring Pulley assembly Washers Thrust bearing Retaining ring Slined hub and roll pin
Compatible with DJ J operators