Devanco Canada - Get The Right Garage Door Opener‎ and Parts

RELAY068

Manaras Relay SPST 24VDC

PRO-J-5011-U-LH

Micanan 1/2HP 115V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft
Emergency disconnect with electrical cut-out switch for manual operation
Three button open-close-stop control station Nema-1
#41 roller chain & sprockets on all internal drives
#50 roller chain and sprockets on final drive
1" permanently lubricated & sealed ball bearings on final drive shaft
External radio control terminal strip
On-Board receiver holds up to 20 transmitters

Specification Sheet

PRO-LJ-5021-U-RH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Right Hand

On-Board receiver holds up to 20 transmitters

PRO-LJ-5011-U-LH

Micanan 1/2HP 115V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

MA026

LiftMaster Pad Only Yellow For 12' Arm

Pad only - arm not included

PRO-GT-7553-U

Micanan 3/4HP 575V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-5081-U

Micanan 1/2HP 208V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

K29-FDCL-500CCB

LiftMaster FDCL Receiver Logic Board with Battery Rev 500

Replacement kit charging circuit board firmware and battery for FDCL

.406-6-R

Cut-to-Length Torsion Spring .406 x 6" Right Hand Wound Blue/Yellow

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

PRO-APTB-7581-U

Micanan 3/4HP 208V 1P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

.375-514-L

Cut-to-Length Torsion Spring .375 x 5 1/4" Left Hand Wound Yellow/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.375-514-R

Cut-to-Length Torsion Spring .375 x 5 1/4" Right Hand Wound Yellow/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

PRO-APTB-5043-U

Micanan 1/2HP 460V 3P Apartment Trolley Operator With Brake N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-APTB-5083-U

Micanan 1/2HP 208V 3P Apartment Trolley Operator With Brake N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-APT-7581-U

Micanan 3/4HP 208V 1P Apartment Trolley Operator N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board

PRO-APT-5081-U

Micanan 1/2HP 208V 1P Apartment Trolley Operator N1 Eyes Monitored ECB (PRO APTE)

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-5083-U

Micanan 1/2HP 208V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-5081-U

Micanan 1/2HP 208V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-7511-U

Micanan 3/4HP 115V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-T-5083-U

Micanan 1/2HP 208V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

60-7244

Econo Caution Sign French 14" x 10"

811-11

Wheel Chock 811-11 Orange Urethane

Not For Use on Ice
High Visibility
Orange Urethane
Size: 11" wide x 8" long x 8" high

60-7248-SC8

Wheel Chock Safety Pkg incl'd: alum. chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) SC-8 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
"Claw" Like Bottom Assures Dependable Grip on Any Surface
Chock Fits Snug Under Tire Contour for Maximum Holding Power
Often Preferred For Snow and Ice Conditions
Light Weight and Reliable
Size: 7" wide x 11-1/2" long x 8" high

.......more details

SC-8

Wheel Chock SC-8 Aluminum

"Claw" Like Bottom Assures Dependable Grip on Any Surface
Chock Fits Snug Under Tire Contour for Maximum Holding Power
Often Preferred For Snow and Ice Conditions
Light Weight and Reliable
Size: 7" wide x 11-1/2" long x 8" high

60-7248-888

Wheel Chock Safety Pkg incl'd: laminated chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) 88-8 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Fabric Reinforced Tire Rubber
Galvanized Steel Sides
Size: 8" wide x 8" long x 8" high

88-8XL

Wheel Chock 88-8XL Laminated Rubber Galv. Steel Sides

Made From Used Truck Tire Laminates Compressed and Fastened Under High Pressure
Galvanized Steel Sides
Size: 11-1/4" wide x 14" long x 14" high

60-7248-888XL

Wheel Chock Safety Pkg incl'd: laminated chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) 88-8XL Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Made From Used Truck Tire Laminates Compressed and Fastened Under High Pressure
Galvanized Steel Sides
Size: 11-1/4" wide x 14" long x 14" high

CMH-94

Wheel Chock CMH-94 Rubber with Integral Handle

One Piece Solid Rubber
Integral Handle
Long Lasting 80 Durometer rubber
Size: 7-1/4" wide x 9-3/4" long x 7-3/4" high

CBI-29

Wheel Chock CBI-29 Cast Ductile Iron

Made from Cast Ductile Iron for Impressive Strength
Painted Blue for good Visibility
Completely Reversible for Simple Use
Size: 8" wide x 12" long x 9" high

60-7248-IC10

Wheel Chock Safety Pkg incl'd: yellow formed steel chock w "tooth" like bottom wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) IC-10 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
"Tooth" Like Bottom Grips Icy/Slippery Ground Surface
Powder Coated Yellow for High Visibility
Formed Steel
Size: 8" wide x10-1/2" long x 9-1/4" high

31337

Doorlec Idler Sprocket with Oilite bushing 50B12 for a 1" Shaft

MSC330V53-BULK

Motor Start Capacitor 330V 53-64MF

BPPB1759

Garex Bottom PVC Moulding for 1 3/4" Door White U shaped 108"(9')

K10-33850

LiftMaster E-Box Cover MH MJ MT

MD-00004

Sprocket 410B12 x 1" 1/4" KW 2 SS 5/16"

PRO-GH-20053-PNL

Micanan 2 HP 575V 3P Gearhead Operator NO CONTROLS *** Price on Request

Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation
Universal Right or Left Hand mount

Installation manual Specification sheet

PRO-APTB-5021-U

Micanan 1/2HP 230V 1P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

203301

ELMON Safety Relay Rail 34-32 230VAC/24VAC/DC 1-Channel w/Testsignal

For DIN-rail mounting

MF00006

Micanan Hex Head Bolt 1/4" - 20UNC 1/2" Full Thread

Used on various Micanan operators
2 required per operator

SRB-5

Standard Riser Bracket 5" Above Dock

Standard 5" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

SRB-4

Standard Riser Bracket 4" Above Dock

Standard 4" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

Specification Sheet

E/BLOP/150

Automatic Systems Safety Edge for BL229 14'-9" (EABLOP/150)

E/1929/031

Automatic Systems Installation Plate Ass'y BL229

Used on the BL229 gate op.

MD-00201

Sprocket 50B40 x 1-1/2" 3/8" KW 2SS 5/16"

748

Fasteners Self Drill & Tap Tek Screw 1/4-20 x 3/4" (#2PT) 1000/Box

Indented Hex Washer Head
7/16" Head
Max RPM = 2000
#2 point = shorter cutting edge (more thread)

MV-00354

Micanan Control Station 3-Btn O/C/S N4 Surface Mount c/w Key Lock-out & Red Pilot Light 24V

R

Molded Rubber Bumper Black 13" L x 12" W 4" Projection 4-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 4 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

DBE-30

Molded Rubber Bumper Black 30" L x 4 1/2" W 3" Projection 6-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 6 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

M2818

Molded Rubber Bumper Black 18" L x 8" W 2" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles
Bumper comes with 2 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

LB1212-36

Laminated Bumper Standard Black 12" L x 36" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1210-24

Laminated Bumper Standard Black 10" x 24" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1012-24

Laminated Bumper Standard Black 12" x 24" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

STATION080

Manaras 3-btn Push-Button Control Station with Key Lock-Out and Pilot Light Nema 4/12

2 N/O contacts and 1 N/C contact for stop.
Surface mount.
Schneider Elect. part no. XALD04H7

LB1010-24

Laminated Bumper Standard Black 10" x 24" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB910-36

Laminated Bumper Standard Black 10" x 36" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB436-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LVB436-11SF

Steel-Faced Laminated Bumper Black 4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TB412-24SF

Steel Faced Laminated Bumper Black 12" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-18SF

Steel Faced Laminated Bumper Black 10" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-14SF

Steel Faced Laminated Bumper Black 10" x 14" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

STRUT-2-1/4-12'-NH

Door Strut 2-1/4" Non Hemmed 12 ft Long

Reinforcement bar 2-1/4"

Q080

LiftMaster Dolly Latch Kit K75-50138

For Liftmaster trolley operator HCT

LB410-18SF

Steel Faced Laminated Bumper Black 10" x 18" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB620-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TB612-36SF

Steel Faced Laminated Bumper Black 12" x 36" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB610-24SF

Steel Faced Laminated Bumper Black 10" x 24" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB636-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LLB620-22SF

Steel Faced Laminated Bumper Black 6" Projection L-Shaped 20" x 22" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.

.......more details

LB610-14SF

Steel Faced Laminated Bumper Black 10" x 14" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB612-36

Laminated Bumper Standard Black 12" x 36" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB612-24

Laminated Bumper Standard Black 12" x 24" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB610-18

Laminated Bumper Standard Black 10" x 18" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB430-11

Laminated Bumper Black 4" Projection Vertical Installation 30" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

HINGE-911-PCG

Powdercoated Hinge #9 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #9 - 0.89 lbs
Powdercoated Grey
For use with 7/16" stem rollers

HINGE-411-PCG

Powdercoated Hinge #4 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #4 - 0.74 lbs
Powdercoated Grey
For use with 7/16" stem rollers

K94-36934

LiftMaster Main Wiring Harness L5

27119

Doorlec Electric Motor TEFC 3/4HP 208/480/575V DC423

Frame size is 56

8-11-1

Strut Clip Sold individually

Hole diameter: 0.260"

9-10-2

Lynx Hand Hoist Chain Zinc Plated 26ft / Bag

Zinc plated silver chain

02-404

LiftMaster Key Switch Assembly On/Off Nema 4/12 **DISCONTINUED

Two Position Key Control Station
Outdoor Surface Mt. (NEMA 4/12)
Non-Tamperproof
OPEN/CLOSE spring return to center (OFF) key removable in center position only.
Should only be used on operators wired for constant pressure to open and close (all LiftMaster industrial operators with type D control wiring).
Die cast metal enclosure

.......more details

K79-32927

LiftMaster Control Board Autogate *** Not Available

Replacement control board used in various Autogate Operators.
Autogate is a gate operator manufacturer that utilizes LiftMaster control boards in their operators
Formally AG001

MF00019

Micanan Hex Head Bolt 3/8"- 16 UNCx1 Full Thread

Used on PRO-GHC
6 required per operator

MH00043

Micanan Flange Bearing 3/8" D **** Replced by MH00096

MD-00060

Sprocket 50B36 1-1/4" shaft 1/4" KW 2SS 5/16"

36 tooth sprocket for #50 chain

41A4208-2

LiftMaster Chain Spreader Kit

Chain Spreader Replacement Kit.
For use with various LiftMaster® and Chamberlain® Chain drive garage door opener models.
Complete kit includes: Chain spreader replacement screws and washers.
Also known as: 41A4208 41A4208-2 062210

PRO-X_MOD-1HP

Micanan Explosion-Proof Modification N-7/N-9 for 1/2HP - 1HP

Modification includes an explosion-proof motor explosion proof fittings operator mounted explosion-proof electrical control enclosure and n explosion-proof three button station.

MM-00126

Micanan Wall Mounting Plate (Reducer 80/100)

MH00003

Micanan Oilite Flange Bushing 3/4 ID x 7/8" OD Sold Individually

2 required per machine

3BLM

Exterior Control Station 3 Button N4 with Mortise Lockout in Metal Enclose

Open-Close-Stop
Dimensions: 7" h x 2-3/4" w x 3-1/2" d
Exterior surface mount

3BLM

MX-00151

Micanan Complete Hoist Shaft Assembly for PRO-GH Includes Pocket Wheel

Includes: pocket wheel shaft bevel gear chain guide spring collars spring pin and washers

K20-1075B-2TLP

LiftMaster Electric Motor 3/4 HP 115/230V 1Ph L3 L4 L5 TEFC

7-21-1A

Lynx Barlock Latch

Comes with screws

Assembly Manual

.331-6-L

Cut-to-Length Torsion Spring .331 x 6" Left Hand Wound Red/White

Priced per inch - cones and filler sold seperately
For factory installed cones use part no. C-600-INSTALLED
For spring filler use part no. SPRING-FILLER

.331-6-R

Cut-to-Length Torsion Spring .331 x 6" Right Hand Wound Red/White

Priced per inch - cones and filler sold seperately
For factory installed cones use part no. C-600-INSTALLED
For spring filler use part no. SPRING-FILLER

BINS-SANDSTONE

Utility Bin Heavy-Duty Stackable Sandstone *** No Longer Available

Usable in virtually every environment both indoor and outdoor and they are made from Polypropylene which will not fade in the sun
Outside dimensions: 16.75" L x 10.75" W x 6.55" H
Inside dimensions: 12.15" L x 8.375" W x 6.5" H
Sold per bin

R4022

Linear GTO Battery and Transformer

Base station not included

37355

Reversing Contactor 120V Coil (replaces cd-11)

H503L5-LH

LiftMaster Ind. Duty Hoist Op. 1/2 HP 208/230-460V VAC 3 Ph Logic 5 Left Hand

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details