Devanco Canada - Get The Right Garage Door Opener‎ and Parts

CP-SH-34-1712-EXP

Lynx Clutch Shaft Assembly for Explosion-Proof HDC Operators

Modified for explosion-proof operators
3/4" x 22 x 3-1/2" thread

25005

Doorlec Cam Shaft with G018 Explosion Proof

MG-00054

Micanan Plastic Spacer for Boards (Medium Length 0.768)

MK-00016

Micanan Fuse Holder

MK-00049

Micanan Overload Reset 3-Phase 1.8 - 2.6 Amps

MK-00052

Micanan Overload Reset 3-Phase 5.5 - 8.0 Amps

MK-00404

Micanan Reversing Contactor ABB Size 1 120V w/Interlock

LC2K1210B7 mini contactor

MK-00039

Micanan Overload Reset 1-Phase 10 Amps

MV-00028

Micanan 24V Commercial Receiver NEMA-4 CR32E-24V

MV-00272

Micanan Key Switch O/C Single Gang Nema 1 Flush Mount

MV-00017

Micanan Key Switch O/C/S Btn Tamper Proof Nema 1 Flush Mount

MV-00012

Micanan 3-btn O/C/S w/Key Lock-Out Metal Housing Nema-4 Pushbutton Control Station

Surface mount
Metal Housing

MV-00004

Micanan 2-btn O/C Nema-1 Pushbutton Control Station

Flush mount

PRO-H-5083U-RH

Micanan 1/2HP 208V 3P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

OSH-6434-ECB-LH

Manaras Opera-SH 1 HP 480V 3 Ph with Electronic Circuit Board Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual

PRO-J-10081-U-RH

Micanan 1HP 208V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

.421-334-R

Cut-to-Length Torsion Spring .421 x 3-3/4" Right Hand Wound Gold

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

.437-514-R

Cut-to-Length Torsion Spring .437 x 5-1/4" Right Hand Wound Red/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.363-514-R

Cut-to-Length Torsion Spring .362 x 5-1/4" Right Hand Wound Green/White

Priced per inch - cones sold separately
For factory installed cones use part no. C-514-INSTALLED

.406-334-R

Cut-to-Length Torsion Spring .406 x 3-3/4" Right Hand Wound Blue/Yellow

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

.319-514-L

Cut-to-Length Torsion Spring .319 x 5-1/4" Left Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-514-Installed

.312-258-R

Cut-to-Length Torsion Spring .312 x 2-5/8" Right Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.295-514-R

Cut-to-Length Torsion Spring .295 x 5-1/4" Right Hand Wound Blue

Priced per inch
For factory installed cones priced seperately - use part no. C-514-INSTALLED

.283-6-R

Cut-to-Length Torsion Spring .283 x 6" Right Hand Wound White

Priced per inch
For factory installed cones priced seperately - use part no. C-600-INSTALLED

PRO-J-7581-U-LH

Micanan 3/4HP 208V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5023-U-LH

Micanan 1/2HP 230V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5021-U-RH

Micanan 1/2HP 230V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5021-U-LH

Micanan 1/2HP 230V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-LJ-5021-U-LH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

.393-334-R

Cut-to-Length Torsion Spring .393 x 3-3/4" Right Hand Wound Orange

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

.273-258-R

Cut-to-Length Torsion Spring .273 x 2-5/8" Right Hand Wound Orange/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

PRO-APTB-7543-U

Micanan 3/4HP 460V 3P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

PRO-APT-7583-U

Micanan 3/4HP 208V 3P Apartment Trolley Operator N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board

PRO-APT-7521-U

Micanan 3/4HP 230V 1P Apartment Trolley Operator N1 Eyes Monitored ECB (PRO APTE)

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board

PRO-APT-5083-U

Micanan 1/2HP 208V 3P Apartment Trolley Operator N1 Eyes Monitored ECB (PRO ATPE)

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-7581-U

Micanan 3/4HP 208V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-TB-5021-U

Micanan 1/2HP 230V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-7523-U

Micanan 3/4HP 230V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-T-5053-U

Micanan 1/2HP 575V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board

2806.206.325

Whiting .206 x 2-3/16 x 32-1/2" Roadside with Cones

60-7248-SC8

Wheel Chock Safety Pkg incl'd: alum. chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) SC-8 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
"Claw" Like Bottom Assures Dependable Grip on Any Surface
Chock Fits Snug Under Tire Contour for Maximum Holding Power
Often Preferred For Snow and Ice Conditions
Light Weight and Reliable
Size: 7" wide x 11-1/2" long x 8" high

.......more details

41C76

LiftMaster Belt Sprocket Cover Kit

Also known as: 041C0076 41C53 41D469 99324608

MM00022

Micanan Support U-Bracket H/HHD MSI0015

Fits PRO-H/HHD

MV-00133

Micanan Control Station 3-Btn O/C/S Nema 4 Surface Mount c/w Pilot Light 24V ** DISC..

LVB1224-11

Laminated Bumper Black 12" Projection Vertical Installation 24" L x 11" W Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LVB1220-11

Laminated Bumper Black 12" Projection Vertical Installation 20" L x 11" W Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB1212-14

Laminated Bumper Standard Black 12" L x 14" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB912-24

Laminated Bumper Standard Black 12" x 24" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB912-12

Laminated Bumper Standard Black 12" x 12" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB812-12

Laminated Bumper Standard Black 12" x 12" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB424-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 24" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TVB620-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LB612-18SF

Steel Faced Laminated Bumper Black 12" x 18" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB610-14SF

Steel Faced Laminated Bumper Black 10" x 14" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

8010

LiftMaster DC Chain / Cable Drive Garage Door Opener ***Discontinued***

Customized DC Motor with soft start/stop action.
Chain/cable square steel rail (SSR) system for efficient operation and standard performance.
Security+2.0 increases remote control range and reduces interference for consistent operation.
PosiLock® electronically protects against forced openings.
The Protector System® invisible light beam auto-reverses the door if there is an obstruction.
Comes with: Door Control Button (883LM) 1-Button Remote Control (891LM)

.......more details

LB412-36

Laminated Bumper Standard Black 12" x 36" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

HINGE-911-PCG

Powdercoated Hinge #9 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #9 - 0.89 lbs
Powdercoated Grey
For use with 7/16" stem rollers

HINGE-411-PCG

Powdercoated Hinge #4 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #4 - 0.74 lbs
Powdercoated Grey
For use with 7/16" stem rollers

HINGE-311-PCG

Powdercoated Hinge #3 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #3 - 0.73 lbs
Powdercoated Grey
For use with 7/16" stem rollers

PRO-PL-INV-200-23

Micanan Wall Mounted Control Panel with Variable Frequency Drive Mod. 2HP 230V 3 PH

Additional charges apply for adding PBS on cover or if panel is not ordered with an operator

MD-00060

Sprocket 50B36 1-1/4" shaft 1/4" KW 2SS 5/16"

36 tooth sprocket for #50 chain

MD-00005

Sprocket 410B12 3/8" NO KW 2 SS 1/4"

ALUM-5P3

Aluminum 24" x 100' Spool Espresso # 5P3

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 5P3
Reverse side is #431 Bright White

Colour chart

2807.139*170

Whiting .139 x 2-3/16 x 17" L Curbside with Cones

For Roadside order part # 2806.139.170

OSH-6232-ECB-LH

Manaras Opera-SH 1/2 HP 208V 3 Ph with Electronic Circuit Board Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"

Installation Manual

VWS-34-BROWN

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Chocolate Brown

Pan head
S point

VWS-34-ZINC

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Zinc

Pan head

7-19-1

Lock Bar Guide Only

41C5497

LiftMaster Wiring Harness Kit High Voltage

For use with various LiftMaster® and Chamberlain® AC Chain Drive Garage Door Openers; manufactured after 2001

MP-00002-460V

Micanan Apartment Feature: Timer-to-Close Function and Light Control Modification only

Controlling action of two lights- sockets supplied on cover

5001-8-WHITE

Residential Side & Top Weather-Strip 8' Long - White

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

MGH-6214-CONT-RH

Manaras 1 HP 240V 1P Jackshaft Contactor Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

74-5FG3A-C

Fuse 3 Amp 250V 5mm x 20mm Glass 5/Pkg

Fast Acting
Sold in packs of 5

PRO-H-7553U-LH

Micanan 3/4HP 575V 3P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

MGH-6537-ECB-RH

Manaras 3 HP 600V 3P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

MU22-2WIRE-U-GRY

Miller Edge MU22 2-Wire Universal Gray - Sold per Foot

��Electromechanical edge for sectional doors and aircraft hangars. •The MU22 is a custom edge manufactured to exact specifications. •The MU22 is completely flexible and will contour to curved surfaces. It's profile can also be square rectangular or angled. •Touch sensitive signaling allows immediate reversal or stopping of motion. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •Vertical or horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

PRO-GH-10053U-L

Micanan 1 HP 575V 3P Gearhead Op. N1 Eyes Monitored ECB Left Hand

Designed for use on all rolling doors and grilles and for large sectional doors with high or vertical lift.
Full function smart 10.0 logic board featuring on-board receiver with antenna and enhanced program selections.
External radio control terminal strip
Three button O/C/S control station Nema-1
Supplied with Nema-1 photocells
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

5001-18-DK-BROWN

Residential Side & Top Weather-Strip 18' Long Commercial Brown

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

PRO-GH-5011U-L

Micanan 1/2HP 115V 1P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

SPECIAL-ORDR-US

Special Order Item USA

Ordered to customer's specs

RW-TS-OPTION

Richards Wilcox Top Seal & Retainer Option Sold per Foot

Available option when purchasing doors

MX00119

Micanan Trolley Hardware Bag Complete (MQ00012)

109435.0001

Overhead Limit Switch

PRO-HBH-7583U-R

Micanan 3/4HP 208V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand

3/4 HP208V 3PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

MH00097

Micanan Bearing 1/2"

MP00087

Micanan Track and #41 Chain for 7' h Door *Actual length 114"*

For 3/4 & 1 HP Micanan trolley operators

PRO-H-5011U-LH

Micanan 1/2HP 115V 1P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters