Devanco Canada - Get The Right Garage Door Opener‎ and Parts

19-5118

LiftMaster Trolley Roller Chain Pack #41 for 18ft Door

For 3/4 & 1 HP trolley operators

20109

Doorlec Hoist Spring EHJ

C-600-114-INSTL

Cones 6" 1-1/4" bore Factory Installed (Pair)

For do-it-yourself installation use part no. SF600-114

SPRING027

Manaras Spring for Floor Level Disconnect Lever

spring for DISCONNECT001

19-5116-NP

LiftMaster Trolley Roller Chain Pack #41 for 16ft Door Nickel Plated

For 3/4 & 1 HP trolley operators

11202

Doorlec Cap Screw 1/4"-20 x 4"

PRO-HBH-7523U-R

Micanan 3/4HP 230V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand (Pro-HHD)

3/4 HP230V 3PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

MD00044

Micanan Spur Gear 12B60

102079

Flangette Retainer football style 2 pieces 2 hole PFL6Z PFL206

2 required per bearing # 101475
works with: 1-1/4" bore sealed insert bearing part # SB206-20

OSH-6213-ECB-LH

Manaras Opera-SH 3/4 HP 240V 1Ph with Electronic Circuit Board Left Hand *** To Extent of Inventory

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation manual Sell sheet

CP-BRG-1

Lynx Bearing 1" *** Replaced by HW-BRG-1

2 in total on a MCJH

K72-33873

LiftMaster Output Shaft Kit MT / BMT

Complete kit includes output shaft bearings sprockets chain roll pin and turac

MARED12

LiftMaster Red LED Light Stip 9.9ft Long ** Discontinued

Provides LED visibility on both sides to 12 ft. arm.

.250-334-L

Cut-to-Length Torsion Spring .250 x 3-3/4" Left Hand Wound Green

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

PRO-GH-10011-U

Micanan 1 HP 115V 1P Gearhead Operator N1 Eyes Monitored ECB

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

MOUNTSHAFT010

Manaras Hoist Shaft Kit for MJH (pre-1998)

Drawing

MOD064C

Manaras Trolley Hoist Kit #410 Chain for OTH

Modification when purchased with an operator
#410 CHAIN WITH FRONTIDLER ASSY
CHAIN HOIST ASSY
HOIST KIT FOR TROLLEY HOIST CHAIN

Drawing

R5996

Shaft Collar 1" Split Black Oxide

MK-00157

Micanan Intrinsically Safe Modification (Safepack)

Modification available for add-on to certain models only

D6375-164-125

Cable Drum High Lift 164" 1-1/4" Bore Torque Force Pair

Maximum hi-lift: 164"
Capacity: 800 lbs per drum
Cable length: Floor to shaft center 181" minus amount of Hi-Lift
Cross reference: DNS 410-164 OMI 164HL M162-4165

CP-PU-DRV-HDC

Lynx Drive Pulley 7/8" x 8" 5L HDC

7/8" shaft
8" diameter

1007-1-5/8-12

Aluminum Bottom Retainer Flat Fits Doors 1-5/8 to 1-3/4" Thick

For door thickness of 1-5/8" to 1-3/4"

8086.225.325

Whiting .225 x 2-5/8 IN x 32-1/2" Roadside with Cones

An original Whiting assembly

7001-WG-10-MO

Residential Wood Grain Side & Top W/S Medium Oak 10' Long - Painted Screws to Match

Medium Oak retainer with Medium Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

7001-WG-9-DO

Residential Wood Grain Side & Top W/S Dark Oak 9' Long - Painted Screws to Match

Dark Oak retainer with Dark Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

7001-WG-9-CO

Residential Wood Grain Side & Top W/S Cherry Oak 9' Long - Painted Screws to Match

Cherry Oak retainer with Cherry Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

ZT35081029

Firestar Fire Door No. 2 Slat 22-GA White

.295-258-L

Cut-to-Length Torsion Spring .295 x 2-5/8" Left Hand Wound Blue

Priced per inch
For factory installed cones priced seperately - use part no. C-258-INSTALLED

MD-00003

Sprocket 41B36 x 1" Bore 1/4" Keyway

2 set screw 5/16

84284

Marantec Logic Board for Non-EOS Models

For use on M Line- M-4500 and M-4700 models.
For use on Q Line - 7500 and 7700 models.
For use on Martin DC 3500E and DC 3700E models.
Replaces 8054216. Special programming needed. Instructions included

39-10541

LiftMaster Clutch Disc for SL595 (K39-10541)

MAW123-BLK-U

Miller Edge Air-Wave Edge Black Sold per Foot

This pressure sensitive air-wave edge can be adapted to suit a wide variety of applications.
When touch activated the MAW123 sends an immediate pulse of air through the extrusion to an air-wave switch which sends a signal to controls to stop and/or reverse operations.
It has been designed to fit most doors with double track bottom retainers.
With appropriate mounting channel this edge will fit nearly all doors from 11/2" to 2" thick.
The MAW123 is resistant to flame water and most common greases and oils.

MK00799

Micanan Smart 10.0 Full Feature Circuit Board Non- Monitored with H.D Relays (MK00701-NM)

For 1 HP 110/220V Single Phase 230/380/460V 3 Ph
The board does NOT have P1 & P2 terminals

Instructions Manual

1104-8'-DK-SAND

Residential Side & Top PVC Weather-Strip with cap 8' Long - Dark Sandstone (DDG)

Garaga dark sandstone rigid vinyl retainer with Garaga dark sandstone flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

41A5507-B

LiftMaster Receiver Logic Board for 2500 (390 Mhz) ** Discontinued

With end-panel
Also known as 41A5507 41A5507B

K1D8052-1CC

LiftMaster Control Board for LA500DC LA400 LA412

014D1270D

1224-GLASS-ONLY

Elton Sealed Glass for frame 1224-1-3/4"

Thermal replacement glass only

MP00022

Micanan Up-Charge Track and #41 chain for 24' h Door *Actual length 318"*

For 3/4 HP and 1 HP operators only

MP00014

Micanan Up-Charge Track and #41 chain for 14' h Door *Actual length 198"*

For 3/4 HP and 1 HP operators only

K72-12493

LiftMaster Limit Switch Kit

Complete kit with limit nut retainer switch plates backup plate depress plate limit switches (3) standoffs screws and locknuts
For logic control MT BMT MJ MH MHS

21-10340

Transformer 115-24V AC 20VA

120V Primary 24V Secondary 20VA

MD00009

Micanan Roller Chain #41 45 Pitch Drive with Link

Length: 4 ft

E076

Rolling Steel Aluminum Bottom Bar 679 Extrusion Sold per Foot

7097

Whiting Cable Drum Assembly for 2-5/8" ID Spring Wire Roadside (LH)

A Whiting original
Cable drum and bearing

SLT17-20P

Rolling Steel 2" Flat Slat 20-ga Primed

SLT2-22

Rolling Steel 2" Crowned Slat 22-ga Galvanized

340.115-CUT

Whiting Top Panel Tongue & Groove 11-1/2" h Cut to Exact Length

Primer only
Customer to specify exact length

UN201

LiftMaster Thermostat Controlled 500-Watt Heater & fan for MAT Gate Operators and more

For temperatures below 32 F
Designed for use with Mega Arm Tower gate operator
Can be used for other applications as required
Heater operates when termperatures are below freezing
Plugs into a standard 120V outlet
500 Watts with a circulating fan

.......more details

Installation Manual

MOD034

Manaras Monitored Photocell Upgrade N1 to N4

Ideal for industrial environments submersible and impact resistant.
Flexible design withstands and realigns after mechanical impact.
Max. range 45ft.
Incl. photoeyes 3ft of conductor wire and mounting hardware.
Applies to all operator models with electronic control "M" types.

D525-216-1

Cable Drum Standard Lift 18' 3-SS Torque Force Pair

18' standard Lift aluminum die cast alloy with 3 set screws.
Pair includes: (1) LH and (1) RH.
Color coded: Red=LH and Black=RH
Max. Door Height: 18'-1" Rated Lift per Drum: 750 lbs.
Max. Cable Diameter: 3/16". Mounting: 1" solid shaft with 1/4" keyway
Cross Reference: DM518 DNS 5-18 OMI 2200

.......more details

PROBE-100

EMX CARSENSE-101 Direct Burial Probe with 100' Lead Wire

Wand only
Requires CS101 (Carsense-101)

CS202S-5-100

EMX Car Sense Vehicle Motion Detector ** Discontinued Offer VMD202 instead

Low voltage used for automatically opening gate when exiting property without requiring the use of a remote control transmitter key pad or any other operator control device.
Can be located up to 150' from the gate. Senses automobiles on a driveway up to 12' wide moving more than 5 m.p.h.
A second probe can be connected in parallel for additional coverage or for automatic opening in or out.
Available in a five wire (recommended for use with GTO operators) and a three wire version.
The CarSense 202 is buried in the ground so it will not be noticed by a potential intruder or vandals.
The CarSense 202 accepts a wide range of power input of 9 - 41 VDC and 6-29 VAC. The low current consumption of 250uA and 12mA detected make the CarSense 202 Slim a great choice for solar applications

.......more details

Installation Manual Sell Sheet

Q311

LiftMaster Surge Protection for Master / Second *** No Longer Available

For the Miracle-One two arm gate operator - master/ slave
Same as part no. K74-50329

Q223

LiftMaster Control Board Master / Second (K001A5869) *** Discontinued

Replacement control board for the Miracle-One gate operator with two arms - Master / Slave.
Same as part no. K001A5869

.306-334-L

Cut-to-Length Torsion Spring .306 x 3-3/4" Left Hand Wound Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

BK304

Jamb bracket J-04 #4 12 gauge

Sold by the piece
Height 3.00" Length 1.9" Width 2.45"
Bright zinc plated 12 gauge steel
2" long track mounting slot
manufactured to accept ¼” fasteners when attaching to the track and 5/16” to lag to the wall.

.319-334-R

Cut-to-Length Torsion Spring .319 x 3-3/4" Right Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-375-Installed

109B33

LiftMaster Trolley Belt Clip

MR00007

Micanan Brake Disconnect Cable 1/16" x 12"L c/w Cable Stop

2 Required per operator

19-5814-NP

LiftMaster Trolley Chain Pack #48 for 14ft Door Nickel Plated

Chain pack only

15-48B10GXX

Sprocket 48B10T 0.750B

MOD050

Manaras Friction Clutch Mod. #50 Chain Gear Head Operators

Installed directly on the output shaft of the operator.
Provides added protection by causing the clutch to slip when the door systems requires adnormal torque to be operated.
Includes sprocket for #50 chain
Operator mounting side must be specified
A spreader bar cannot be used in conjunction with this modification
This modification applies to OGH and MGH operators

.......more details

SETR2641-TM

Erone 4-Channel Wireless Wall Switch Transmitter 433MHz

For sun-blinds and awnings.
Frequency: 433.92 MHz.
Range: Up to 200m (Open-field).
Dimensions (L x W X D): 80 x 80 x 25mm.
Input voltage: 3V Battery (CR2032).

User Manual Wireless System Chart

SSNT-1

Super Sneaky Low Headroom Garage Door Hinge No Tabs Sold as a Pair

SSNT version designed to accommodate top panel struts. Eliminates troublesome & costly double track kits.
No tab design for doors with built-in or requiring a top panel strut
100% effective in 6" headroom
Provides maximum headroom clearance & smooth operation
Self positioning easy install & works on all residential doors
Works with all draw bar type automatic operators

.......more details

12-10331

Flanged Bearing 3/4" x 1-1/2" x 1/8"

CLUTCHPAD007

Manaras Clutch Pad 1-3/4" ID 5" OD

K76-36398

LiftMaster Electric Motor 1/2HP 24VDC for CSL24V / CSW24V

Replacement motor with improved brush assembly for CSL24V and CSW24V gate operators

PPLK1-10

LiftMaster Passport Lite 1-Button Mini Remote with Sec+ 2.0 Technology 10/PKG

Passport Lite Remote Controls provide cost-effective single button access solutions for gate access only or high-capacity commercial properties applications such as employee parking lots and tenant garages.
These remote controls are specifically designed for gate access control and are not compatible with LiftMaster Garage Door Openers.
2x the range of standard remote controls
Narrow-band transmission on 3 simultaneous frequencies (310 MHz 315 MHz 390 MHz)
Compatible with LiftMaster® commercial receivers (850LM 860LM PPWR STAR1000) and Security+ 2.0™ Gate Operators
Keychain remote control sold in a 10 pack

.......more details

Programming Instructions Instructions de programmation Sell Sheet Brochure

V1104-WHITE

Replacement Vinyl Only for 1104-White 200ft Roll

Sold in 200 ft rolls only

20386R

Genie Sequencer Board AC Screw Drive

For Genie Screw Drive garage door opener models: PRO95 CM8600 CM7600 Series II ISL950A IS550
Replaces part number 31184R

HSC-600-JAWS

Replacement Jaws for Hand Swager

Can be used as replacement jaws for both the HSC-600 hand model and the HSC-600-B bench model

MX00150

Micanan Complete Clutch Shaft Assembly for PRO-HHD

7001-10-W/B

Commercial Side & Top Weather-Strip 10' Long - White/Black (WB)

White galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

7001-7-W/B

Commercial Side & Top Weather-Strip 7' Long - White and Black (WB)

White galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

GHX-6112-CONT-L

Manaras Explosion Proof Gear Head 1/2HP 120V Contactor Left Hand

Nema 7/9 control box
Electrical connections from motor to control box consists of hazardous location certified fittings and NEMA 7/9 O/C/S push-button station

Installation Manual Sell Sheet

APOW3

LiftMaster Transformer 120V input 34VDC output

Plug-in AC/DC converter
Used as a replacement transformer for all LA400 models

735

Fasteners Flat Washer 3/8" USS Zinc 1000/Box

ID: 0.40625’’
OD: 0.8125’’
THK: 0.066’’

MK-00648

Micanan 1-Channel 24V Receiver with Antenna

Comes with antenna MK00719
Total of 20 regular remotes can be programmed or 200 of the block coded remotes MK-00660

Programming Instructions

G65-19084

LiftMaster Thermostat Control Heater Fin Type for 208V-460V Gate Operators ** Discontinued

Heater used in BG type gate operators

Installation Manual

761

Fasteners Flat Head Carriage Bolt 1/4-20 x 1-7/8" 1000/Box

Full length thread
Max torque = 6

756

Fasteners Slotted Track Bolt 1/4-20 x 5/8" 1000/Box *** Temp Unavailable *** Offer 734

Knurled shank
Max torque = 6

23-2016

LiftMaster Limit Switch

Limit Switch for the VSL595

99553NYHNG

Nylon Hinge Black #3 *** To extent of inventory

Equivalent to 14-ga in strenght

29-31229

LiftMaster Relay 24VDC 30A SPDT 1-Phase only

C-relay for model T operators 10A

SSZP17-1

Solid Shaft 1" Keyed Zinc Plated 17'-1" ** to extent of inventory

SSZP9-6

Solid Shaft 1" Keyed Zinc Plated 9'-6"

SSZP7-6

Solid Shaft 1" Keyed Zinc Plated 7'-6"

6X42PO50

Devanco Loop 6' x 42' pave-over 50' lead-in

Ideal for use on with gravel driveways or sufaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation Instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

MK-00002

Micanan Timer Module (2 wire)

19-5810

LiftMaster Trolley Chain Pack #48 for 10ft Door

Chain pack only

772

Fasteners Lag Screw Hex Washer High Profile 5/16" x 2" 1000/Box *** No Longer Available

7/16" Head
Hex washer high profile head

751

Fasteners Self Drill & Tap Tek Screw 1/4-20 x 1" (#2PT) 1000/Box

7/16" Head
Indented hex washer head
Max RPM = 2000

H755L5-LH

LiftMaster Ind. Duty Hoist Op. 3/4 HP 575 VAC 3 Ph Logic 5 Left Hand

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details