Devanco Canada - Get The Right Garage Door Opener‎ and Parts

6X16PO50

Devanco Loop 6' x 16' pave-over 50' lead-in

Ideal for use on with gravel driveways or sufaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation Instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

1003-2-8'

Aluminum Bottom Retainer L-Shaped 8' Long

For 2" thick doors.

MK-00051

Micanan Overload Reset 3-Phase 3.7 - 5.5 Amps

.283_6"-LH

Torsion Spring .283 x 6" x 12ft LH White

Wire size: .283
Inside diameter: 6"
Length: 12 ft

7001-12-W/B

Commercial Side & Top Weather-Strip 12' Long - White and Black (WB)

White galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (10)

26-14321

Truck Door Bottom Panel with Seal (11" x 98") for Todco Dryfreight Doors

These panels are cut to an extra wide width to fit wider vehicle applications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment
3/4" thick 7 ply exterior grade medium density plywood Primer finish
Comes only with bottom retainer and seal (installed)

T-53-S

FL-Allstar 3-btn 27-Door O/C/S Transmitter 107475-311 MHz ***NLA

This remote can control (open-close-stop) up to 27 doors.
It has a eight switches encoder with three positions: + 0 and - .
Manufacturer's model number: 535T (190-107475)
Dimensions: 6 1/4" x 3 3/8" x 1 3/8"

Programming Instructions

OSH-6433-M-N1-RH

Manaras Opera-SH 3/4HP 480V 3Ph Monitored w/ N1 Eyes Right Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation brake and a floor level engaging device
Clearence: side room required 16"

.192_2-3/16_60R

Spring Wire .192 x 2.188 x 60" CTD RAW RH

.192 x 2-3/16" x 12'

MB-01007

Micanan Electric Motor Only 1/2HP 220V 1PH

Limited duty motor
Used on Micanan's LT LJ LH LHA

R5210

Pulley 4" Zinc Plated Steel with Sheave Strap

Bored for 3/8" diameter bolt
Maximum cable diameter: 1/4"
Hardened inner race
Includes fork

TA-2-S/L-1200

Assembled Track Set 2" Comm 14g Bracket Mount for 1-3/4" Door Std Lift 12" Radius

Includes horizontal and vertical tracks

DHJ501L5-RH

LiftMaster Ind. Duty Hoist/Jackshaft Op. 1/2 HP 115/230 VAC Logic 5 Right Hand***Discontinued

Industrial-Duty Hoist/Jackshaft Operator with Internal Door Lock Sensor
Optimal for shopping mall applications with heavier rolling doors and grilles.
Provides a floor level chain hoist to ease manual operation in an emergency or power outage.
Includes a door lock sensor to prevent damage to the door and operator caused by attempts to automatically open a locked door.
Industrial Ball Bearings on 1" Output Shaft
Second Floor-Level Disconnect for Manual Lifting in an Emergency

.......more details

029-98290

W-Style Replacement Door White Stainless Steel Package 029-98290

Replacement door size between 96-1/4" - 98" wide x 72-90" high
Painted white
Stainless steel package

1104-7FT-WHITE

Residential Side & Top PVC Weather-Strip with cap 7' Long - White (W)

White rigid vinyl retainer with white flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

.363_5-1/4"-LH

Torsion Spring .363 x 5-1/4" x 12ft LH Green/White

Wire size: .363
Inside diameter: 5-1/4"
Length: 12 ft

1104-9FT-BROWN

Residential Side & Top PVC Weather-Strip with cap 9' Long - Brown (N)

Brown rigid vinyl retainer with brown flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

25E10272

Truck Door Stud Plate for Bottom Roller Black E-coat finish for Whiting Roll-Up Doors (2 Stud)

Steel construction Black E-coat finish
Stud plate for 2 stud
Cross Reference: W #2032

26CW94322-CUT

Truck Door Bottom Panel with Seal (12" x Cut-To-Size) Painted White for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes only with bottom retainer and seal (installed)

.......more details

220205-02

Linear Complete Hardware Kit for LDO LSO LCO

Includes all the hardware needed to install the operator in its entirety.
Includes the rail hardware (door bracket and header bracket) and hardware for installing the safety beams.

OTBH-6232-M-N1

Manaras Trolley Operator 1/2HP 208V 3Ph Monitored w/N1 Photoeyes

The OTBH is a heavy-duty low headroom trolley operator
Designed for use on industrial standard lift sectional doors
It incorporates a drum-band type solenoid brake
25 cycles per hour 80 cycles per day
1/2 HP operators come with # 48 (410) roller chain
Includes PHOTO-070

.......more details

K40-35246-2

LiftMaster Warning Sign Kit English Pack of 10

UL325 requires that ALL installations MUST have warning signs placed in plain view to warn pedestrians of the dangers of motorized commercial door access systems

28-2103

Steel Bumper Extension Bracket 4"D x 20" Tall 12"W

4" deep (projection) x 20" tall x 12" wide

TDC1222-20

Liftmaster Comm. 20FT Trolley Angle set (10-5820-P x 2) and #41 chain pack (TDC41-20) and spacer pad (71-10324***Actual length 275"***

Double Angle Rails for doors up to 20'6" high
Includes #41 chain pack and Spacer pad part # 71-10324

RXTA-100

Pulse 2-Channel Receiver

Two-Channel Receiver: Can be programmed to operate one or two doors or for Open/Close or Open/Stop functions.
Universally Adaptable: Works with most available brands/models of transmitters (300-390MHz) including those with rolling code.
9-30Vac/dc input.
FCC approved.

TXTA-KYPD

Pulse Universal Wireless Keypad

Programmable 4-digit code for continuous use.
Programmable TEMPORARY 4-digit code for programmable number of uses.
Multi-Brand Adaptable: Works with all Pulse receivers LM receivers (GreenOrange Red Purple and Yellow learning codes) and other receivers with 315MHz or 390MHz.
Powered by 9V battery. (One included in package)

27121-600V

Doorlec Electric Motor 1-1/2 HP 600V 3PH DC223C

1676.98

Whiting Bottom Seal 96" for 1801 U-Channel ** Price by Quote

Special order item. Price by quote only

38252A.S

Genie Opto Wheel

The opt-wheel normally needs replaced if your garage door opener is short traveling in both directions (open and close) in the excess of 6 inches at a time then stopping.
Compatible with models: 1028 2028 1128 2128 1035 1055 2036 2035 2055 3035 3055 2033 3053 3155 7035 7055 7053 7135 7155

10TD900PB

BEA Wired Transmitter 900mhz Flagged Flag Connectors AAA Battery

Multi-colour LEDs on receiver provide installer with visual notification of signal strength and activation status.
Frequency: 908-918 MHz
Radio Control Type: Digital
Programmable Capacity (standard): 75/unlimited universal
Operating Temperature: -10-55C

PRO-HBH-10083U-L

Micanan 1 HP 208V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand

1 HP208V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

40629A.S

Genie Wire Harness for Door Lock

Includes 1 wiring harness only
Connects to the door lock for Genie Wall Mount garage door openers Overall length 10'
Compatible with models 6070H 6070H-B 6072H-BO 6072H-O 6170H 6170H-B 6172H-BO 6172H-BSV 6172H-BV 6172H-O

487135

Bircher Easy Loop Bracket

Bracket for part #487132

5-18-4

Tapered Angle Continuous 2" Heel x 129" L Sold in PAIRS

For 2" track up to 2" thick

MX000641

HySecurity Left Counterweight Mount for StrongArm

Compatible with StrongArm systems
Designed for left-hand configurations
Supports balanced gate movement
Reduces strain on gate operators

R2TAES

Erone Radium 2-Button AES128 Encrypted Mini Transmitter

Compatible with any high-security AES128 wireless receivers they were designed to prevent the cloning of remotes.
The code sent by the transmitter changes at each activation removing any scanning and copying risk.
A special algorithm ensures a continuous synchronization between the receiver and remote.
Includes AES128 encryption
Compatible with RADIUM AES128 receivers
Heavy-duty construction

.......more details

O02R9506

AirLift O Ring Orig. Op-AirLift

41A8910

LiftMaster Chain Idler Pulley

GHX-311-3/4HP-RH

Doorlec Explosion Proof Gear Head 3/4 HP 120V 1PH ECB Right Hand

Nema 7/9 control box
Electrical connections from motor to control box consists of hazardous location certified fittings
NEMA 7/9 O/C/S push-button station included

31120-112-3/8

Doorlec Sprocket 50B36 1-1/2" Bore 3/8" KW

36 tooth sprocket

1-0199

RW Hinge 700 03 x 7 18" (36" Open) Black

Straps: Formed steel 3/8" thick x 2-1/2" wide (basic width)
Pin: 3/4" dia steel Zinc plated. Pin loose with cotter pin
Bearings: 2 hardened steel disc bearings
Finish: Complete hinge black enamel
Fasteners are not included

114-0298

RW Support 18 x 33

Size: 18 x 33
Material: Formed Steel 3/16" thick
Finish Black Enamal

MULTI-GROOVE

Garex Ready to Install Door Multi-Grooved Special Order

Available with a choice of simple and varied colors this textured woodgrain door will meet your style and requirements for quality and durability
R-16

2807.192.290

Whiting .192 x 2-3/16 x 29" Curbside with Cones

GALV-319-6-R

Cut-to-Length Torsion Spring .319 x 6" Right Hand Galvanized Blue/Green

Spring wire only. Cones and Filler extra

2376.206.35.940

Whiting Torsion assembly .206 wire size 35" spring length 94" shaft

210264

Skylink Case Cover Atoms

1222_DUAL_TROLLEY_14'

LiftMaster Dual Trolley kit for 14' high door includes #41 Chain for 14ft High Door Angle tracks (2x) 14' (Actual length 227") and (1x) shaft

Provides a second drawbar-type operation on wide standard door
Includes 14ft tracks #41 chain hardware & Round Bar 1" x 20'
Works with TDC12 & TDC22 Maxum operators

2110-274

Linear Clutch Shaft Assembly HSLG UPS

LB610-102

Laminated Bumper Standard Black 102" x 10" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

27120-575V

Doorlec Electric Motor 1/2HP 575V 3PH DC221

OSHW-6112-M-N4-L

Manaras Opera-SH w/Carwash Mod 1/2HP 120V 1Ph Mon ECB w/N4 Photoeyes Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
Solenoid activated Brake

.......more details

H11G03-SS

Hinge #3 x 11 gauge Stainless Steel

Manufactured with 11ga. Rust-Resistant 304 Stainless Steel
Universal Design
Fits Most Overhead Sectional Doors
Priced Per Each

RB-TX10C

Miller Edge RBand Monitored Wireless Edge Transmitter

RBand transmitter only
On board diagnostics allows for easy set up and troubleshooting.
Offers pulsed and normally open outputs.
Ideal for commercial door operators manufactured after 2010.
Bi-directional link improves immunity to RF interference.
Nema 4

.......more details

GALV-306-6-L

Cut-to-Length Torsion Spring .306 x 6" Left Hand Wound Galvanized Red Price per Inch

Priced per inch - cones sold seperately
For factory installed cones use part no. C-6-INSTALLED

GALV-343-6-144-R

Torsion Spring .343 x 6" x 12ft RH Galvanized Blue/Red

Wire size: .343
Inside diameter: 6"
Length: 12 ft
Galvanized

GALV-306-6-144-L

Torsion Spring .306 x 6" x 12ft LH Galvanized Red

Wire size: .306
Inside diameter: 6"
Length: 12 ft
Galvanized Stenciled

CP-SH-34-MC3-65

Lynx Complete Limit Shaft Assembly #65 Chain

For trolley operator

TDC48-08

LiftMaster Trolley Chain Pack #48 700LBS 8ft Door

Chain pack only
TDC48-08 is a #48 Chain Pack Kit for 8 Ft. Trolley Rail Assemblies.
For use with LiftMaster® MAXUM TDC 700 Series Standard-Duty Trolley Commercial Door Operators; installed on 8' commercial doors.

OPJ-6433-M-N1

Manaras Heavy-Duty Jackshaft Operator 3/4 HP 480V 3 Ph Monitored ECB w/N1 Photoeyes

An industrial operator designed for use on standard high and vertical lift sectional doors
Can also be used on rolling doors and grills
It incorporates a floor level disconnect mechanism for manual operation
25 cycles per hour 100 cycles per day
Continuous-duty single phase capacitor start or 3 phase motor open drip proof
Mechanical brake

.......more details

BCSI-PM19

Pivin Drapeau Keyway 1/4 x 1" *** Price by Quote Only

086565.1013.S

Overhead Door Chain RLR #25 x 62P Loop

29140

Doorlec Transformer 230V pr 120V sec 50VA

230V primary 120V secondary 50VA

GALV-331-334-R

Cut-to-Length Torsion Spring .331 x 3-3/4" Right Hand Wound Galvanized Red/White

Priced per inch - cones sold seperately
For factory installed cones use part no. C-334-INSTALLED
Galvanized

GALV-319-334-L

Cut-to-Length Torsion Spring .319 x 3-3/4" Left Hand Wound Galvanized Blue/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-334-INSTALLED
Galvanized

99119671-PER-FOOT

Amarr Bottom U-Seal 3.5" Black Double Dovetail Vinyl 1/4" T Sold per Foot

1/4" T width
Used on Amarr Residential Open Back Doors and Classica models

041D8993

LiftMaster Cover Silver 8365W 83650-267

Replacement LiftMaster® Cover.
Compatible with various LiftMaster® 8365W Series WiFi® AC Chain Drive Garage Door Openers; powered by myQ

GALV-283-2-R

Cut-to-Length Torsion Spring .283 x 2" Right Hand Wound Galvanized White Price per Inch

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

GSD103L5R

LiftMaster Heavy Ind-Duty Slide Operator 1HP 208/230/460VAC 3PH

GALV-406-6-144-L

Torsion Spring .406 x 6" x 12ft LH Galvanized Blue/Yellow

Wire size: .406
Inside diameter: 6"
Length: 12 ft
Galvanized Stenciled

CP-MO-34R-123/1

Lynx Electric Motor 3/4 HP-IR 115/230V 1 Ph

Electric motor only with instant reverse

GALV-225-2-L

Cut-to-Length Torsion Spring .225 x 2" Left Hand Wound Galvanized Ornage/Green Price per Inch

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

K72-12532

LiftMaster Output Shaft Kit J

Also known as: 308116010J 310-116010J 308116010JK 310116010J
Compatible with LiftMaster® Model J Commercial Door Operators

41D3485

LiftMaster Chain Kit 10'

For use with various chain drive garage door openers that utilize a T-rail and have a 10' garage door
Same as 041D3485

2237.1

Whiting Coldsaver Intermediate Panel 13-1/2" x 93-3/4" *** Price by Quote Only

Fits Coldsaver Roll-Up Doors
1-1/8" thick 96" wide

E/1929/023

Automatic Systems Balance Spring Ass'y 5.5 MM BL229

Used on the BL229 gate op.

OSH-6114-M-N1-RH

Manaras Opera-SH 1 HP 120V 1 Ph Monitored w/N1 Eyes Right Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual

MODKIT027

Manaras Universal Aux. Output Module B060 Field Install

MODKIT027 for field install simply plugs into the control board
Controls traffic lights
Works with BOARD060
Can only be used on operators with BOARD060 pre-installed for operators built prior to October 14 2010.

OTBH-6532-M-N1

Manaras Trolley Operator 1/2 HP 600V 3 Ph Monitored w/N1 Photoeyes

The OTBH is a heavy-duty low headroom trolley operator
Designed for use on industrial standard lift sectional doors
It incorporates a drum-band type solenoid brake
25 cycles per hour 80 cycles per day
1/2 HP operators come with # 48 (410) roller chain

GUSSET-MOUNT

Doorlec Gusset Mount Plate Up-Charge (L Bracket) GH

Mounting plate for GH op

OSH-6434-M-N1-LH

Manaras Opera-SH 1 HP 480V 3 Ph Monitored Board w/N1 Eyes Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual

MD00093

Micanan #410 Roller Chain 45 Pitch c/w Connecting Link

GHX-353-1HP-RH

Doorlec Explosion Proof Gear Head 1 HP 575V 3PH ECB Right Hand

Nema 7/9 control box
Electrical connections from motor to control box consists of hazardous location certified fittings
NEMA 7/9 O/C/S push-button station included

RSH-6814-MON-RH

Manaras Rapido Jackshaft Operator 1 HP 208V 1PH W/ Elect. Board N4X Thru Beam Eyes Right Hand

High speed heavy-duty v-belt drive industrial operator.
Designed for use on properly counter-balanced standard high and vertical lift sectional doors weighing a maximum of 750 lbs.
Two times the speed of the standard jackshaft operator
Manages soft-starts and soft-stops
Can be wall or shelf mounted on either side of the door
Cast iron pillow block bearings

.......more details

RSH-6814-MON-LH

Manaras Rapido Jackshaft Operator 1 HP 208V 1PH W/ Elect. Board N4X Thru Beam Eyes LH

High speed heavy-duty v-belt drive industrial operator.
Designed for use on properly counter-balanced standard high and vertical lift sectional doors weighing a maximum of 750 lbs.
Two times the speed of the standard jackshaft operator
Manages soft-starts and soft-stops
Can be wall or shelf mounted on either side of the door
Cast iron pillow block bearings

.......more details

2376.156.19.780

Whiting Torsion assembly .156 wire size 19" spring length 78" shaft

19-50ML-SS

Master Link #50 Stainless Steel

CGH205L5-RH

LiftMaster Gearhead with Brake & Carwash Mod. 2 HP 575V 3P L5 Right Hand

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting.
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

CGH205L5-LH

LiftMaster Gearhead with Brake & Carwash Mod. 2 HP 575V 3P L5 Left Hand

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting.
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

GALV-343-334-144-R

Torsion Spring .343 x 3-3/4" x 12ft RH Galvanized Blue/Red

Wire size: .343
Inside diameter: 3-3/4"
Length: 12 ft
Galvanized

GALV-306-334-144-L

Torsion Spring .306 x 3-3/4" x 12ft LH Galvanized Red

Wire size: .306
Inside diameter: 3-3/4"
Length: 12 ft
Galvanized Stenciled

GALV-250-2-144-L

Torsion Spring .250 x 2" x 12ft LH Galvanized Green

Wire size: .250
Inside diameter: 2"
Length: 12 ft
Galvanized Stenciled

XF208VAC12

LiftMaster 208V Transformer Kit 1200

BEA-10LIGHT-TG

BEA Modular LED Signal Light Segment Green

Signal lights for industrial and vehicle flow management applications.
LED signal modular lights offer customizable configurations with “build-your-own” lighting elements that share a common base and bracket.
These LED signal units are available in red green yellow and an audible alarm cap and can be stacked in a tower configuration with up to six modules.
Operating temperature: -40 to 122F
Nema 4/IP65
Base sold separately

.......more details