Devanco Canada - Get The Right Garage Door Opener‎ and Parts

BOARD003

Manaras Repl. Circuit Board MA-50 110V Lite Duty

Used on model MDTB

MOD065B

Manaras Trolley Hoist #41 Brake Release Kit Includes 12' Shaft

Chain hoist for manual hand operation of standard lift doors equipped with trolley operators.
The 1" cross-header shaft (12' long) drives the front idler of the drawbar
For use with operators with #41 chain
When applicable it incorporates an electric cut-out and brake release cable
Hand chain for 14' high door is standard
Hoist assembly width is only 8.5"

.......more details

18212

Limit Switch LS2 G3M Female

For use with Rite-Hite dock levelers

BEARING047

Manaras Flange Bearing 2-Bolt Black for 1' bore

2 set-screw holes 1/4-28 at 90 degrees. Set-Screws NOT included
Replaces BEARING012

MA020T

LiftMaster Mega Arm Tower Replacement Cover

Mega Arm Tower Cover.
Compatible with LiftMaster® Barrier Gate Perimeter Access Systems Operators.

MA005

LiftMaster Gear Reducer 60:1

Replacement Gear Box (60:1).
Compatible with LiftMaster MADCBB MATDCBB MASTDCBB

2100-258-UPS

Linear Tension Bolt UPS 1/2 Chain

Used on various Linear Gate operators

XBA18

NICE Indicator Lights for L-BAR Arm 26.2ft

The Nice Apollo XBA18 is a 26.2 ft long line of indicator lights for the click fixture on the upper or lower side of the barrier arm of the L-Bar barrier gate openers.

25-42-320

Extension Spring 7' Door - 320 lbs Green w/ clip

Double - Loop
25" long 42" stretch 320 lb load
Sold individually
Rated for 10000 cycles

ETBHW-311-3/4HP

Doorlec 3/4 HP 115V-1Ph Waterproof Trolley OP

Trolley Industrial type operator with DC2000 Logic controller
Watertight/Dust tight

CP-BR-ASSY-115V

Lynx Brake Kit with 115V Solenoid CDJH

Complete brake kit with solenoid

CB14B0500-KOR

Cable 1/4" 7x19 500' Galvanized Supreme

Galvanized Cable 1/4" 7x19 500ft spool.
Cable break strength: 2000 lbs
A higher quality cable compared to the Chinese cable.
Meets endurance test requirements of over 35000 work cycles
Lubricated for flexability and longer service life

308301

Linear 2-Channel Multi-Code Key Ring Transmitter 300 MHz

Open/Close remote for 2 doors
Compatible with 300 MHz Multi-Code receivers and Model 109950 and 302850 receivers
Easy access to battery and coding switches - 10 dip switches
Power: 12-volt battery
Codes: 1024 codes for each channel (set by dip switches)
RF frequency: 300 MHz

.......more details

Programming instructions

E/BLOP/148

Automatic Systems Safety Edge for BL229 11'-6 (EABLOP/148)

EHJW-311-1/2

Doorlec Ind Jackshaft Op. Watertight ECB 1/2 HP 115V-1Ph

Heavy-Duty Industrial Operator with Waterproof Mod. for Sectional or Rolling Steel Doors
DC-2000 logic with adjustable Timer-To-Close Delay On Reverse and Traffic Light Control (monitored board optional)
Solenoid Brake prevents coasting and secures the door when closed
TEFC (sealed) continuous duty electric motor with overload protection
Automatic Friction Clutch protects the door and operator
Self-aligning Heavy Duty sealed Pillow Block bearings on all shafts for high cycle applications

.......more details

CDJH-12-115-ECB

Lynx CDJH Heavy-Duty Jackshaft 1/2 HP 115V with ECB UL325

New LX100 circuit board.
Built-in 3-channel 372 Mhz radio receiver accepts up to 20 remotes
4L V-belt primary reduction #41 drive chain and sprockets.
Adjustable friction clutch Inherent Mechanical Brake included
Solenoid brake optional **
Fully driven adjustable limit switches.

.......more details

MOTOR009-WIRED

Manaras Electric Motor1/2HP 120/240V 1PH

Instant reverse intermittent-duty electric motor only for MTBL MJ MJH MTH & MTBH models
1725 rpm built-in reset
Wired either 120V or 240V ECB

MOD114A

Manaras Synthetic Oil Upgrade Only

This Upgrade Mod. is only available when purchaed with a compatible operator
Synthetic oil is placed in the operator's reducer for improved performance stability and decreased sensitivity to temperature variances

E402-00-FM

Doorlec Ersce Utility Switch 6A/230V Roller Arm ** Indef. Delivery

Utility switch with a 'NO' and a 'NC' contact
Adjustable arm with roller
Made in Italy

HCT08

LiftMaster HCTDCU Rail Only

Yellow zinc dichromate premium rail finish offers maximum rust protection in open-air environments.
Heavy-duty 12-gauge C channel corrosion resistant steel track.
This DOES NOT include the head unit

27091A

Genie Limit Worm Gear for PMX500

Limit worm gear sits in the Limit switch plate and works with the Limit Worm Drive to activate the limit wheel
Works With Genie Models PMX 500-IC/B IC250/B

ACP00922

Nortek LCD Display Assembly AE5/AE1K ***NLA***

Replacement screen only

MA020

LiftMaster Mega Arm Replacement Cover

MA-020 is a Mega Arm Replacement Cover.
Compatible with LiftMaster® Mega Series (MA/MAS) Commercial Gate Operators ONLY

37557R

Genie Chain Drive Bullet Assembly

This Genie chain drive bullet assembly is the white piece that holds the chain for the garage door opener together.
Works with chain model Genie garage door openers that have a C-Channel rail.
The chain carriage assembly for these models also attaches to this chain bullet assembly allowing it to move the garage door open and closed up and down the rail.
Assembly contains: The 2 Bullet side white pieces and the four screws to install it
Compatible with Genie models that have a chain rail: 1028 2028 3020H 3020H-B 3024 4024 3022 3042 3120H 3120H-B 4022 4042 4124 4164 (ChainMax ReliaG IntellG and TriloG series with these model numbers)

85503

LiftMaster Belt Drive DC Battery Backup Wi-Fi W/Camera

Integrated Camera. Camera manually adjust 360 degrees to see everything that happens in the garage
HD-Quality Video. Glare-resistant night vision lens auto-adjusts to light levels in the garage to capture everything and anything that passes through the garage
Live Streaming and Video Storage. View a live-stream of your garage for free. 7-day and 30-day video storage options are available via a monthly subscription.
2-Way Audio. Communicate in real time between your garage and your smartphone
MyQ Technology now with Wi-Fi® enables secure monitoring and control of your garage door opener with a smartphone tablet or laptop.
DC Motor Belt System delivers powerful ultra-quiet performance.

.......more details

Receiver Logic Board Conversion List

RDO-321-3/4

Doorlec RDO Rolling Curtain Op. w/ECB 3/4HP 230V 1PH

Additional charge for doors over 14' high

91-00401

Truck Door Step Bolt 1/4"-20 x 1.50" (3/4" head)

Zinc plated finish
Cross Reference: T #80015-1610

41A2818

LiftMaster Limit Switch Drive Gear Kit

For use with various LiftMaster® and Chamberlain® Residential Garage Door Openers.
Complete replacement kit includes: helical gear e-clip and grease tube

VBELT_5L290

Manaras VBelt 5L 26" - repl. by B26

Used on OMJ OMH
Type B belt

R5213

Bearing Flangette Retainer Only Standard

Does not include bearing
For use with all C16-32F and C20-32F
Steel Zinc plated finish

SGP-311-1-115/1

Doorlec Gate Master 1 HP 115V 1 Phase with Heater

Post mount heavy-duty industrial slide gate operator
Max. gate weight: 2500 lbs
Gate travelling speed: 45 ft / minute
175 watt heater with thermostat included
Includes Omron reflective photocell

MB-01007

Micanan Electric Motor Only 1/2HP 220V 1PH

Limited duty motor
Used on Micanan's LT LJ LH LHA

RESET005

Manaras Resettable Overload Fuse 8A 1 Phase

41D0277-2

LiftMaster Transformer WiFi Non-Battery Backup

For Wi-Fi models without BBU garage door openers; manufactured after 2011
Same as #204D0277-2

BRAKEPART020

Manaras Brake Shoe Assembly Kit (SHOE021/022)

LOTBINIERE-R16

Garex Ready to Install Door Special Order

R16 Insulation - Overlay moldings positioned to create the Lotbiniere design - Moldings are factory white or can be factory painted to match door colour - Optional decorative hardware is available - Available in steel (std colours) or aluminum (white and grey) - A variety of decorative windows can be added - Custom colours can be factory painted - Multiple hardware configurations are available to accomodate site requirements - Composite end blocks eliminates corrosion and wood deterioration

URBAN-MR-R16

Garex Ready to Install Door Special Order

R16 Insulation - Narrow multi rib pattern - Available in steel (std colours) or aluminum (white and grey) - A variety of decorative windows can be added - Custom colours can be factory painted - Multiple hardware configurations are available to accomodate site requirements - Composite end blocks eliminates corrosion and wood deterioration

PREM-SEL-MX-R16

Garex Ready to Install Door Special Order Premium Select MX R16

R16 Insulation - Mix of short and long panels - Available in steel (std colours) or aluminum (white and grey) - A variety of decorative windows can be added - Custom colours can be factory painted - Multiple hardware configurations are available to accomodate site requirements - 7' to 9' wide doors will have 1 short and 1 long embossment - 10' to 11' wide doors will have 2 short and 1 long embossment - 12' to 18' wide doors will have 2 short and 2 long embossments - Composite end blocks eliminates corrosion and wood deterioation

2807.187*300

Whiting .187 x 2-3/16 x 30" Curbside with Cones

WHTG-COLDSAVER

Whiting Special Order ColdSaver Door ** POR

Special order to customer's specs
2-1/8” thick panels built with aluminum facings inside and out for easy cleaning and excellent acceptance of paint and decals.
No rivets on face of door to interfere with lettering or decals.
Aluminum extruded panels .070” thick resist puncture.
Foam-in-place urethane insulation.
Panel joints are double sealed.

.......more details

K44-1210-4XD

LiftMaster E-Box Enclosure N4

Plastic replacement box only

CA-151-412

Continuous Angle 1-1/2" x 4-1/2" x 151.5" L Sold per Piece

12-ga angle

ME00006

Micanan Intermediary Shaft 1" x 10-7/16" c/w KW

MGR20-Y-2R-04

Miller Edge Sensing Edge Round Yellow 2-Wire Right Hand Outlet 4ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

MX00218

Micanan Clutch Shaft Assembly for PRO-LH

E/1929/022

Automatic Systems Round Arm Ass'y 10' (BL229)

Used on the BL229 gate op.

12-3000

Flanged Bearing 1-1/4" x 1/8" **to extent of inventory

Fits SW470 gate operator

.289_3-3/4"-RH

Torsion Spring .289 x 3-3/4" x 12ft RH

Wire size: .289
Inside diameter: 3-3/4"
Length: 12 ft

CHW401-114-TFRCE

Chain Hoist Wall Mount 4:1 1-1/4" 2000R Torque Force (126658)

4:1 Reduced drive
Sprocket: 41B36x114 Bore: 1-1/4"
Includes: 26ft of hand chain 1/4" square key chain keeper and 3.6ft of #41 roller chain included with sprocket wheels.
Cross Reference: 2000R OMI 4006

Drawing Sell sheet

P-0128/LH

Autogate Retro Bracket Left Handed System

This is needed to change over to their current motor

422LMC

LiftMaster 2-Channel Co-Axial Receiver 390 MHz ***DISCONTINUED

Smart Garage Door Opener® electronics on each channel for fast programming
Bell wire attached for easy second channel hook-up
18 - 35VAC/DC
FCC certified 390MHz

MSC330V72-BULK

Motor Start Capacitor 330V 72-86MF

26117

Doorlec Limit Cam Retainer Plate with Fasteners

Fits Most Doorlec Commercial operators except Explosion-Proof Operators
Will not fit on waterproof operators with small electrical enclosure built before 1999

60-6560-C-YELLOW

Speed Bump Yellow 36" Econo Light Weight for Concrete *** NLA

A standard speed bump system section includes (2) main pieces (2) endcaps x 5” long and (1) connector clip.
Main pieces may be added and connected to form larger units.
36” long x 10.5” wide x 2” high (main piece)
EndCap: 5” Safety Snap On End Cap - sloped modular profile prevents tripping by pedestrians.
Yellow Plates: Each speed bump section is embedded with (6) yellow safety plates of weather resistant composite material for protection from salt freeze and thaw.
Can be used as a cable cover - bottom sides include 1” x 1½” channels for protecting temporary or permanent cables or hoses.

.......more details

MOTOR256

Manaras Electric Motor 1 HP 120/240V 1PH

Continous-duty base mount ODP 60Hz

ME117-M-BLK-U

Miller Edge 4-Wire Monitored Black Universal Outlet Sold by the Foot

Electromechanical slide in edge for 1" to 2" sectional doors.
Touch sensitive signaling allows for immediate stopping or reversing of motion. The ME117 is resistant to water flame and most common greases and oils.
Temperature range: -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Installation manual Sell sheet

Q076

LiftMaster Turn Buckle Kit K75-50132

For Liftmaster trolley operator HCT

JB-02P-W

Miller Edge Junction Box Nema 4

For use with commercial door operators and CPT sensing edges from Miller Edge
Waterproof
Accommodates wire .181 to .312

Installation instructions

M-0319

Autogate Groschopp Inline Motor 24V

P-0129/RH

Autogate Retro Bracket Right Handed System

This is needed to change over to their current motor

P-0130

Autogate Motor Belt Tensioner Upgrade Kit

This isneeded to change over to their current motor

050DCDDOWF

LiftMaster Receiver Logic Board WiFi Dock Door Jackshaft

050DCDDOWF is a Receiver Logic Board Replacement Kit.
Compatible with LiftMaster® Model DDO8900W DC Light-Duty Commercial Jackshaft Operators; featuring WiFi®

41A6689

LiftMaster Trolley Threaded Shaft D-Shape

For use with various LiftMaster® Belt Drive Garage Door Openers that utilize a T-rail.

D-67

Linear 1-Channel Digital Receiver 303 MHz

Designed for use in security systems and remote switching functions.
Typical applications for the receiver include adding a wireless zone a panic button or creating a remote arm/disarm feature for a hardwired alarm panel
Operates on 11-24 VDC or 12-16 VAC power
One channel
Standard digital format: 256 discrete codes
One form “C” relay output

.......more details

K1D8424-1CC

LiftMaster Power Board 3 Ph SL585U/SL595U

For use with LiftMaster® SL585U & SL595U Series; and various 3 Phase Commercial Slide Gate Operator Models.

7206

Whiting Balancer Bracket End - Curbside for Whiting Roll-Up Doors for #7176 Balancer

Steel construction
Plain finish
Whiting original

SPR41B36X11/4

Sprocket 41B36 x 1-1/4" Bore 1/4" Keyway

Same as MD-00322

J753L5

LiftMaster Industrial-Duty Jackshaft 3/4 HP 575V 3Ph L5

Doors used with this operator should be balanced with the ability to be manually lifted by hand in an emergency or power outage.
The operators are typically mounted to the wall when used with smaller sectional overhead doors with a vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
J operators are attached to the door jackshaft to indirectly drive the door
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Security+ 2.0® safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you

K20-1100-1T

LiftMaster Electric Motor 1/2 HP 115V 1Ph TEFC **DISCONTINUED

Compatible with LiftMaster® Model SW490GL Swing Gate Operators
Also known as: 20-1100-1T 2011001T G2011001T

GHX-6432-CONT-LH

Manaras Explosion Proof Gear Head 1/2HP 480V-3P Contactor Left Hand

Nema 7/9 control box
Electrical connections from motor to control box consists of hazardous location certified fittings and NEMA 7/9 O/C/S push-button station

H5NA12

Richards-Wilcox Hinge 5NA x 12 Gauge Roller Bracket

Galvanized 12 gauge hinge

ME120-BLK-2WIRE-E

Miller Edge Black 2-Wire End Outlet Sold per Foot

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

ME120-BLK-2WIRE-L

Miller Edge Black 2-Wire NM Left Hand Outlet Sold per Foot

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

601815

RG6 77% BR Coaxial Cable

Black coaxial cable
This price is for 1000 feet

TRACK-SET-2STD-12

2" Tracks Set 12'-0" Torsion 1-3/4" Door Clips for Wood Frame 12" Radius *** By quote only

SF514U-114-W

Spring Fitting 5-1/4" Winding Side Only for 1-1/4" shaft

Universal thread for use in either LH or RH wound springs.
Includes: (1) winding side only

TRACK-SET-2STD-10

2" Tracks Set 10'-0" Torsion 1-3/4" Door Clips for Wood Frame 12" Radius *** By quote only

KP-680-ETL

Koala Air Blower 1/2 HP *** Indef. Delivery

Powerful extra quiet and energy efficient 1/2 HP motor
115V / 1 Speed
Durable super lightweight and compact Polypropylene housing design
ETL/CETL Safety Certified

1224-2-BLACK

Elton Commercial Window for Flush Doors 2" thick 1224 Black Frame Sealed Glass

Screw together window kit
Thermal window
Frame size: 25-1/8" x 13-1/8"
Cut-out size: 24-1/16" x 12"
Vision area: 21-11/16" x 9-5/8"
Different glass options and frame colours are available upon request

.......more details

RSW12UL

LiftMaster Res. / Light Comm. DC Swing Gate Operator 12VDC Heater Not Incl.

Includes safety device LMRRUL Monitored Retroreflective Photo Eye enhanced retro-reflect
Features battery backup that provides up to 147 cycles or 63 days of standby power
Smooth Start/Stop Operation and mid-travel reversal extend operator and hardware life.
Heavy-Duty Commercial Gear-Driven Transmission provides unsurpassed reliability.
myQ® Technology enables you to securely control and monitor your gate operator from anywhere
Security+ 2.0® safeguards access with an encrypted tri-band signal to virtually eliminate interference and offer extended range.

.......more details

Sell sheet Brochure

LMTBUL

LiftMaster Monitored Through Beam Photo Eye w/ Heater Nema 4X

Tested and evaluated by UL and meet UL 325 requirements.
Long Range powerful beam provides reliable performance.
Sensing distance up to 90 ft.
Anti-Fogging Lens
NEMA 4X rated
Wireless network mode eliminates the need to wire between operators in dual-gate applications.

.......more details

Installation manual Manuel d'installation Product guide

12502

Doorlec Clutch Plate Aluminum 4" dia x 5/8" bore

Works with model LJ/LJH

HD3120-BLACK

Commercial 3" Inside Slide Lock Black Powder Coated

Track use: 2" or 3"
Throw: 2.62"
Slide bar: 0.138"
Individually wrapped

BK000-B/BLACK

Residential Top Roller Bracket Adjustable 2-Bolt Black Powder Coated Sold per Piece

Sold per piece - not sold as a pair
Meant for 2" hardware
Individually wrapped

GBUP412EF-1

Gate Roller 4-1/2" x 2-3/8" Polymer Sold Individually

Polymer gate roller with bracket for 4-1/2" upright post
Works with gate pipes that are 2-3/8" thick or less

E/1929/071

Automatic Systems Round Arm Ass'y 16'-5" (BL229)

Used on the BL229 gate op.

GAL.262-258-144L

delete

LZE500

Erone L & Z-Bracket for Maglock ESM500

CAP378

Capacitor 110/125VAC 378-454MFD

378-454 mF 125 VAC 50/60 Hz
Used on 1/2 HP LiftMaster operators

BTN-8L5-GR

Devanco green replacement button for 8L5-OCS

green replacement button for 8L5-OCS

SELECTOR-8L5

Devanco replacement rotating 8 position switch selector for 8L5-OCS

replacement rotating encoded 8 position selector for 8L5-OCS

1004-2-14'

Aluminum Bottom Retainer 2" U-Shape with Reinforcement 14 ft***Actual Length 14'2"***

For door thickness 2"

BCSI-PM10

Pivin Drapeau Clutch Plate for BCSI Gate Operator ** Price by Quote Only

Friction Plate

SF175-S

Spring Fitting 1-3/4" Stationary Side Only 1" shaft

8155W

LiftMaster 1/2HP AC Belt Drive Wi-Fi with one light ***No Longer Available

Free MyQ® Mobile App so users know their home is secure.
Built-In Wi-Fi® for the easiest way to connect the garage.
Real-Time Alerts indicate the status of the garage door via email or push notifications.
Monitors and Controls the opener from anywhere using mobile devices.
Belt Drive system for quiet maintenance-free performance.
Motor Vibration Isolation System (MVIS®) provides quiet reliable operation.

.......more details

Installation manual Sell sheet Brochure

MT22-MON-GRY-LH

Miller Edge 4-Wire Monitored Pressure Sensitive Edge Gray Sold per Foot

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

MT22-MON-GRY-RH

Miller Edge 4-Wire Monitored Pressure Sensitive Edge Gray Sold per Foot

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty