Devanco Canada - Get The Right Garage Door Opener‎ and Parts

02-401

Push Button Control Station 1-Button Surface Mount NEMA 1

Die-cast metal enclosure
START may be used as OPEN with all LiftMaster operators.
May be used as OPEN and CLOSE on all operators with type B2 control wiring

5X10PO50

Devanco Loop 5' x 10' pave-over 50' lead-in

Ideal for use on with gravel driveways or sufaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation Instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

59LMC

LiftMaster Outside Keyswitch ** To Extent of Inventory

12 tumblers provide double locking action
Self cleaning barrel weather-resistant aluminum plate
Cannot be shorted out from exterior with key
One "NO" contact used to activate the door operator
Includes two keys

Installation Manual

BK110/PR

Light Duty End Bearing Plate 3-3/8" with Bearing - EBF 338 Residential Sold as a Pair - LH/RH

With C16-32F bearing
Galvanized steel
3-3/8" shaft offset
Flange allows plate to be bolted to the wall for additional support
Same as part number 209

7FT-RAIL-SCREW

LiftMaster 7' screw drive rail 3077SD

One piece rail

DTG

Linear Delta3 Safety Edge Transmitter 310 MHz

Activates one Delta-3 receiver for remote stop or reverse safety edge
No cables or coiled wires
Mounting screws (4) supplied
Power: 9-volt battery
Codes: 256 (set by dip switches)
RF frequency: 310 MHz

.......more details

Programming Instructions

ACT-31B

Linear 1-Channel Block Coded MegaCode Key Ring Transmitter 318 MHz (ACP00879)

Compatible with all Linear access receivers and controllers
Supplied with quick-disconnect key ring
Power: Two CR2016 batteries incl.
Codes: Factory block coded in MegaCode format
RF frequency: 318 MHz
Dimensions: 1.25" W x 2.25" H x .48" D

.......more details

Programming Instructions

V300-TS

Top Seal Weather Strip 100 ft per Roll

For use with bottom retainers installed on top of door.
Vinyl: Black

F539.90000

Bircher Infrared Programming Remote RC Duo 2 Red

Conveniently program all parameters from ground level
Backlighting of specific buttons provide instant confirmation of programmed parameter & value
Configure any Hercules 2 Hercules 2s Reflex 2 or UniScan sensor with the same remote
Multiple address feature allows programming of a single sensor even in close proximity to other sensors
Large highly visible buttons
Automatic off feature conserves battery life

.......more details

Programming Instructions F539.90000 Sell Sheet

975LMC

LiftMaster Laser Parking Assist ** To extent of inventory

Works with Chamberlain (LiftMaster) Garage Door Openers
Easily connects with two wires to the photocell terminals of the opener
The Laser light turns on as you drive into the garage
Simply Adjust the light to a specific spot on the dash

Installation Manual Manuel d'Installation

GREASE

Gear and Rail Grease 3/4 oz Tube *** No Longer Available

A low temperature lithium based grease
To avoid tooth wear premature failure and temperature rise caused by friction by promoting sliding between teeth

50-450

LiftMaster Interlock Switch for Sectional Door Nema 4 (Same as 50-13529)

Interlock switch is engaged by the door side lock and disables operator control.

.225-134-L

Cut-to-Length Torsion Spring .225 x 1-3/4" Left Hand Wound Orange/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

37220R

Genie Replacement Safety Beam Set

Works on all Genie model openers including Legacy with 2-pin connector safety beams
Not compatible with openers made before 1995
Brackets and wiring included
Will work with all Genie and Overhead Residential openers that were manufactured with photo-eyes

MV00077

Interlock Switch for Sectional Doors

Mounts on the door track to prevent the use of the operator when the door is locked

8FT-RAIL-CHAIN

LiftMaster 8' chain drive rail 1708LMC - colour code: Blue

#48 chain size
Price reflects cost if purchased with an opener

7FT-RAIL-CHAIN

LiftMaster 7' chain drive rail 1707LMC - colour code: Green

#48 chain size
Price reflects cost if purchased with an opener

CPS

LiftMaster Commercial Protector System Eyes

Universal commercial photo-eye kit for indoor use
Interface box allows CPS to work with all operators
24 volt AC/DC supply voltage
Mounting hardware included
Sensing distance of 30 feet
Receiving Eye - A: 001D6857-1 Sending Eye - A: 001D6857-2

.......more details

Installation Manual

485LMC

LiftMaster Battery for Integrated BBU Units

For use in Liftmaster 8550 8500W 3850 and 8360 models
12V 4.5 AMP
Same as Part # 41A6357-1 41A5948
Battery back-up good for 20 cycles

Installation Manual Manuel d'Installation

.437_3-3/4"-LH

Torsion Spring .437 x 3-3/4" x 12ft LH Red/Green

Wire size: .437
Inside diameter: 3-3/4"
Length: 12 ft

.283_3-3/4"-LH

Torsion Spring .283 x 3-3/4" x 12ft LH White

Wire size: .283
Inside diameter: 3-3/4"
Length: 12 ft

.243_3-3/4"-LH

Torsion Spring .243 x 3-3/4" x 12ft LH White/Yellow

Wire size: .243
Inside diameter: 3-3/4"
Length: 12 ft

.273_2"-LH

Torsion Spring .273 x 2" x 12ft LH Orange/Red

Wire size: .273
Inside diameter: 2"
Length: 12 ft

.283_1-3/4"-LH

Torsion Spring .283 x 1-3/4" x 12ft LH White

Wire size: .283
Inside diameter: 1-3/4"
Length: 12 ft

829LM

LiftMaster Garage and Gate Monitor Sec+ 2.0 **to extent of inventory

This innovative monitor lets you check and close the garage door or gate from any room in the house.
Green and Red LED lights indicate whether the garage door or gate is open or closed.
Volume controlled audible alert lets you know when the garage door or gate is being opened.
Able to monitor and close up to four garage doors or gates.
Compatible only with new Sec+ 2.0 MyQ compatible garage door and gate operators.

Programming Instructions Instructions de programmation

30B363

Capacitor Motor Start 53 uF - 64 uF 220V *** No Longer Available

R-831-J

FL-Allstar 1-Door O/C/S Receiver in Oil Tight Case (JIC) 107478-311 MHz **NLA

This receiver is included in a JIC box.
Like the model R-831-P it has three isolated contacts to open close and stop the doors and a possibility of 6 561 operational codes to enhance the security level. If your operator can be controlled by three button station then our R-831-J receiver and commercial remote controls will work with your operator.
Manufacturer's model number: 190-107478
Dimensions: 9 1/4" x 6 7/8" x 1 1/4".

Programming Instructions - Dip Switch Version Programming Instructions - Learn Button Version

FL-KEYPAD

FL-Allstar Wireless Keypad 110927-311 MHz

This wireless keypad controls up to four doors.
Manufacturer's model number: (190-110927)
Dimensions: 6" x 2 3/8" x 1 1/4".

Programming Instructions

T-833-C

FL-Allstar 3-btn 9-Door Transmitter 109023-311 MHz***NLA

This nine channel transmitter controls up to nine doors (open-close) or three doors (open-close-stop).
It has a height switches encoder with three positions: + 0 and - .
Manufacturer's model number: 8833TC (190-109023)
Dimensions: 4 5/8" x 2 1/4" x 7/8"

Programming Instructions

144C56

LiftMaster Idler - Cable Pulley for chain drive

For square rail assemblies
Same as 144C0056

885LM

LiftMaster Wireless Control Panel Security+2.0

For use with Security+ 2.0 garage door openers that have a yellow Learn button.
The wireless control panel can be used as a secondary device to open & close the garage door and to turn on & off the lights on the opener.

885LM Manual

.437_6"-RH

Torsion Spring .437 x 6" x 12ft RH Red/Green

Wire size: .437
Inside diameter: 6"
Length: 12 ft

.393_6"-RH

Torsion Spring .393 x 6" x 12ft RH Orange

Wire size: .393
Inside diameter: 6"
Length: 12 ft

.295_5-1/4"-RH

Torsion Spring .295 x 5-1/4" x 12ft RH Blue

Wire size: .295
Inside diameter: 5-1/4"
Length: 12 ft

.375_3-3/4"-RH

Torsion Spring .375 x 3-3/4" x 12ft RH Yellow/Green

Wire size: .375
Inside diameter: 3-3/4"
Length: 12 ft

.273_3-3/4"-RH

Torsion Spring .273 x 3-3/4" x 12ft RH Orange/Red

Wire size: .273
Inside diameter: 3-3/4"
Length: 12 ft

.243_3-3/4"-RH

Torsion Spring .243 x 3-3/4" x 12ft RH White/Yellow

Wire size: .243
Inside diameter: 3-3/4"
Length: 12 ft

.319_2-5/8"-RH

Torsion Spring .319 x 2-5/8" x 12ft RH Blue/Green

Wire size: .319
Inside diameter: 2-5/8"
Length: 12 ft

.218_2-5/8"-RH

Torsion Spring .218 x 2-5/8" x 12ft RH Yellow/Orange

Wire size: .218
Inside diameter: 2-5/8"
Length: 12 ft

41A4373A

LiftMaster Safety Sensor Kit 1993-1998 ** Replaced by 041-0136 & 041-0155-000

For LiftMaster Chamberlain & Sears openers built from 1993-1998
Kit includes: Saftey sensors 24" wire and gel connectors
Replacement: 041-0136 with the 041-0155-000 brackets

17300

Doorlec DC-3000T3 3-btn Transmitter 313 MHz

One block of 10 dip-switches for programming
Will activate 3 Doorlec 17307 receivers (DC-3000R)
Includes visor clip and 9V battery

Programming Instructions

17307

Doorlec DC-3000R 1-Channel Receiver 313 MHz

10 dip-switches for programming
24VAC power input
1 N/O relay

Mounting Instructions

MK00488

Micanan Electronic Circuit Board Monitored

Replacement board for PRO-LH (50-11)
Board has terminals P1 & P2
Up to 20 transmitters can be programmed

Instructions Manual

MJ00002

Micanan Brake Shoe - Right **No Longer Available**

Only available in complete kit # MJ00013 or MJ00014 for PRO-GH

T3B-DS

Lynx 3-btn Transmitter Dip Switch 303 MHz

Ultra secure mid-size transmitter with 8 dip-switches for coding
3-buttons provides control for 3 Lynx operators
Compatible with HomeLink in-vehicle remote control
Can be mounted on visor with saddle clip or carried on a keychain
Visor clip and 12V battery included
Will work with Lynx residential operators built from 2000 and up.

.......more details

Compatibility chart

H14GHALF

Half Hinge #1 x 14 gauge

Bright zinc plated 14-gauge steel hinge
For use with 7/16" diameter stem rollers
Full body hinge 1-5/8" wide with slotted holes

SEL2641R433-IP

Erone 2-Relay Stand Alone Receiver Pulse/Latch or Delayed Relay Output 433MHz

Up to 85 transmitter keys
1 NO relay + 1 NO/NC relay (24VA)
Self-learning memorization
Standard pulse latched or timed relay output
Power requirements: 12/24Vac/dc
Dimensions: 105 x 45 x 28mm (4.3 x 1.75 x 1.1in)

.......more details

Instruction Manual Sell Sheet Wireless System Chart

CONTACTOR044

Manaras Schneider Reversing Contactor 12A-24VAC

Reversing contactor with 24V coil
Same as part # LC2K12107B7
Demensions: 3.5" long x 2.25" wide x 2.25" high
Use 03-8024K as possible replacement

TRANSF088

Manaras Transformer 480-24V 40VA

Transformer 480V Primary 24V Secondary 40VA

MH5011U-LH

LiftMaster 1/2 HP 120 Volt Medium Duty Jackshaft Operator

1/2 HP 120 volt 1 phase medium-duty hoist operator Logic board with integral 315 MHz radio receiver for Open/Close or Open/Stop/Close
CPSU commercial photoeyes included ( Nema 4 optional)
4L V-Belt #48 drive chain adjustable friction clutch
Emergency disconnect and chain hoist standard
Solenoid actuated disc brake
Door speed approximately 8" to 12" per second

.......more details

Installation Manual Manuel d'installation MH Sell Sheet MH Shop Drawing

8331.96

Whiting Brush Top Seal assembly 96"

Fits Coldsaver and Tempguard

AP5

Linear MegaCode Wireless Access Controller 318 MHz

Ideal for gated communities parking facilities and industrial sites
Easy to set-up and use up to 480 remotes can be programmed with a few keystrokes
Easy to add suspend and delete transmitters through programming mode no transmitter dipswitches to set
Supports 480 block coded transmitters or 238 individual transmitters/wireless keypad entry codes
Supports up to six fully supervised safety edge transmitters
AP-5 replaces Linear's AP-4; AP-5 available for replacement of existing AP-4 units only

.......more details

Programming Instructions

831-R

Allstar 1-Door O/C/S Receiver 107480 318 MHz ** To Extent of Inventory

Three channels - three relay outputs
Textured aluminum case
Terminal strip for wiring
Wire whip antenna with "F" connector
Compatible with Allstar Classic Allister and Pulsar dipswitch transmitters and MVP quik-code transmitters
Power: 24 VAC

.......more details

Programming Instructions - Dip Switch Version Programming Instructions - Learn Button Version

MGR

Linear 1-Channel MegaCode Gate Receiver 318 MHz

��Single Form ”A” (normally open) relay rated at 30 Volts AC/DC up to 5 Amps
Supplied with whip antenna three feet of coaxial cable and bulkhead connector
Memory: storage for up to 40 MegaCode transmitters
Power: 12 - 30 VAC or 10.5 - 30 VDC
Codes: 1000000+ (MegaCode format)
RF frequency: 318 MHz

.......more details

Installation Manual

1336.8

Whiting Stainless Steel Roadside Top Closure Bracket for 8" radius

1336.6

Whiting Stainless Steel Roadside Top Closure Bracket for 10" radius

RV-300

3" Vinyl Insert for Brush Retainer per foot

Color: Black

4006-6FT

Aluminum Retainer only for Light Brush 6' Long 45 degree

For angle application (45 degree)
For use with Light Brush or Vinyl Insert.

1016

Storm Shield Sold per Foot with 1 caulk tube of adhesive per 20ft

Installed underneath garage door to prevent water from flowing into garage.
Can be driven over with vehicle
Color: Black
Width: 3-3/16" Thickness: 0.5" (highest point)
Comes with 6 x 10.3oz caulk tubes per 100'

Installation Instructions

1019-1-3/8-12'

Rigid Vinyl Bottom Retainer Flat 12' Long

Black - for door thickness of 1-3/8"

1006-2-24'

Rigid Vinyl Bottom Retainer U-Shaped 24' Long

Black with flexible fin to touch door face.
For door thickness 2"

1006-2-12'

Rigid Vinyl Bottom Retainer U-Shaped 12' Long

Black with flexible fin to touch door face.
For door thickness 2"

1005-1-3/8-24'

Aluminum Bottom Retainer U-Shaped 24' Long *** 24' is DISC

For door thickness 1-3/8"

PATCH_6X12

Truck Door Aluminum Trailer Patch 6" x 12"

Adhesive back adheres to a wide variety of material easily covering holes or other blemishes on trailers.
Forms a shock resistant watertight seal.
Painted white

1003-1-5/8-12'

Aluminum Bottom Retainer L-Shaped

For 1-5/8" thick doors.

1003-1-3/8-10'

Aluminum Bottom Retainer L-Shaped

For 1-3/8" thick doors.

1104-8FT-BLACK

Residential Side & Top PVC Weather-Strip with cap 8' Long - Black (B)

Black rigid vinyl retainer with black flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

1104-10FT-SAND

Residential Side & Top PVC Weather-Strip with cap 10' Long - Sandstone (D)

Sandstone rigid vinyl retainer with sandstone flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Also known as Taupe

PULL-CHAIN

Pull Chain Spring Only 12" Long

Spring Only for pull chain device
Used with a hand chain for full vertical doors.
Eliminates the need for leaf bumpers

1106-10-BLACK

Commercial Side & Top Weather-Strip 10' Long - Black

Aluminum retainer with black dual fin vinyl

32-48-170

Extension Spring 8' Door - 170 lbs Orange ** Replaced by 27-48-170

Double - Loop
32" long 48" stretch 170 lb load
Springs sold individually
Rated for 10000 cycles

Spec Sheet

32-48-60

Extension Spring 8' Door - 60 lbs Brown ** check for availability

Double - Loop
32" long 48" stretch 60 lb load
Springs sold individually

973LMC*

LiftMaster 3-btn Security+ Transmitter 390MHz - DISCONTINUED

390 MHz Secruty+ three button visor tranmsitter
Compatible with Security+ systems including Chamberlain Sears Craftsman and Raynor Openers (Safety Signal) manufactured 1997-2005
Visor clip and battery included (part # CR2032)
Same as 973LM 96LM 953CB 956CB
Discontinued 12/31/13 - Replacement options 375LMC 890MAX 893MAX 892LT 894LT

28-02101

Truck Door 2" Vertical Track and Right Angle Assembly 106.5" Roadside (LH) for Whiting Roll-Up Doors

SPECS: Length: 106.5" Fits door sizes: 91" - 100" high
Assembly includes: Right angle mounting track Vertical track and Torsion bracket
Cross Reference: W #2275-2
Galvanized steel 14 gauge construction
Tongue and groove for proper alignment at joints

27-20305

Truck Door Balancer Bracket Center for Whiting Roll-Up Doors

Steel construction
Plain finish
Cross Reference: W #2525

27-20300

Truck Door Cable Drum Roadside (LH) for Todco Roll-Up Doors

Cast aluminum construction
Large die cast cable drums are grooved to prevent cables from binding or wearing prematurely.
Angle of cable slot determines left or right drum.
Holds up to 130" door cable
Cross Reference: T #59033-2 T #59129-2 W #4014 330000

26-40402

Truck Door Reefer Side Seal 98" Long for Whiting Coldsaver

Co-extruded using PVC backing with flexible PVC seal against the door.
Cross Reference: W #7470

26-40400

Truck Door Dual Durometer Side Seal 5/16" Track Spacing 114" Long for Whiting Dryfreight Doors

Allows for easy door operation.
Seal protects cargo area from dirt and moisture
Will not bunch up as bottom panel goes around top curve.
Co-extruded using rigid PVC backing with flexible PVC seal against the door.
For use with right angle vertical track
Fits only right angle vertical track assembly.

.......more details

26-40027

Truck Door Bottom Seal 98" Long for Whiting Dryfreight Doors

Flexible PVC material
Cross Reference: W #1676

26-40026

Truck Door U-Channel Seal Retainer 96" Long for Whiting DryFreight Doors *** DISCONTINUED

Aluminum extrusion construction
Cross Reference: W #1801

26-40001

Truck Door Bottom Seal Standard 98" Long for Todco Roll-Up Doors

Extruded from long lasting rubber
Prevents dirt and moisture from entering cargo bay.
Cross Reference: T #80840 W #3257 610200

DM4X8

Cable Drum Standard Lift 8' 400-8 Pair

8' Standard Lift aluminum die cast alloy.
Pair includes: (1) LH and (1) RH Color coded: Red=LH and Black=RH
Max. Door Height: 8'-1".
Rated Lift per Drum: 265 lbs
Max. Cable Diameter: 1/8"
Mounting: 1" tube or solid shaft with 1/4" keyway

.......more details

25E10002

Truck Door End Hinge & Roller Cover Black E-coat finish for Whiting Roll-Up Doors

Steel construction Black E-coat finish
Removable cover allows roller change without hinge removal
Cross Reference: W #1209 T #70162
Box quantity: 50

R5115

Bearing 1" Commercial with Flanged Retainer Football Style

1" Commercial bearing pressed in a Flanged Retainer Football Style
Type: Steel Bore: 1"
Inner Race Offest: 13/64"
Rated Load Cycles: 250 lb @ 10000 cycles (8')

RN1124

Roller 2" Nylon 4" stem 11 ball White

White Nylon Roller Wheel Diameter: 2"
Working Length: 3.75" Overall Length: 4.69"
Box qty: 150 Box weight: 49 lbs (2-4-11 White Nylon)

R5209

Cast Iron Pulley 4"

Bored for 3/8" diameter bolt
Maximum cable diameter: 1/4"
Cast iron pulley mounted on two pressed sealed bearings
300lb load rating

S-HOOK_SMALL

S Hook #8 Small 1/8" x 1-3/8"

HD3080

Step Lift Plate Curled

Step Plate/Lift Handle

HD3120

Commercial Inside Slide Lock for 2" or 3" track

Track use: 2" or 3"
Throw: 2-11/16"
Offset from inside face of door to lockbar: 1/2"
Bright zinc plated steel with spring actuated lock bar.
Same as part number 270

25-10113**DISC

Truck Door 2" Steel Roller Long Stem for Whiting Roll-Up Doors Use Part # 94-61180-33-84

Unplated shaft 10 roller ball design
Shaft Length: 6.5" Overall Length: 7.5"
Long stem roller has a staked collar design versus machined collar on others.

25-10100

Truck Door 1" Steel Roller 2.5" Shaft Length for Todco Roll-Up Doors

Zinc plated Hardened shaft and raceways
Seven roller ball design
Cross Reference: T #61174 T #69162 W #4026 W #4027 291000
Box quantity: 25

25-10001

Truck Door End Hinge for Todco Roll-Up Doors

Zinc plated steel construction
Four-knuckled to ensure smooth door operation
Cross Reference: T #69035 W #4007 220000

4X8SC50

Devanco Loop 4' x 8' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation Instructions Instructions d'installation Loop Placement Guide Guide de positionnement des boucles

6X16PO50

Devanco Loop 6' x 16' pave-over 50' lead-in

Ideal for use on with gravel driveways or sufaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep