Devanco Canada - Get The Right Garage Door Opener‎ and Parts

TIMER031

Manaras Timer 24/240V 1s-100h *** To Extent of Inventory

This timer-to-close can be added to any Commercial garage door opener.
Use with RELAY022 (8-pin base) if required.
Schneider Elect. part no. RE88867215

Adding a timer

MA116RDOT

LiftMaster White Aluminum Arm with Retro-Reflective DOT Tape 17 ft

For use on Mega-Arm gate operator
Red White reflective DOT stripe

Additional arm accessories

.192_1-3/4"-LH

Torsion Spring .192 x 1-3/4" x 12ft LH Silver

Wire size: .192
Inside diameter: 1-3/4"
Length: 12 ft

.363_5-1/4"-LH

Torsion Spring .363 x 5-1/4" x 12ft LH Green/White

Wire size: .363
Inside diameter: 5-1/4"
Length: 12 ft

TS-1-159-GALV-KEY

Tube Shaft 1" x 159 (13'.25) Galv w/KW 1/4" x 3/8"

When ordering order one foot longer that actual door width
Comes with 3 keys 1/4-3/8-3'' long

MOUNTSHAFT001A

Manaras Clutch Shaft Kit for MJH

Input / clutch shaft kit for MJH built after 1999

Drawing

Q200

LiftMaster Chain Coupling Release K07-50215

For Liftmaster trolley operator HCT

CS303-FP-50

EMX Car Sense Direct Burial Sensor Flat Pack 50ft ** Replaced by LRS-FP-50

Lead probe ONLY. Requires the CS303-C-1 detector.
Easy installation above or below ground
Ignores cross traffic in tight spaces with DETECT-ON-STOP™ feature
Sensitivity display
Single cut installation with flat pack model

97-75000

DOT-C2 Reflective Tape 24" x 2" W 6" Red x 6" White Pattern

DOT-C2 certified exceeds NHTSA requirements
Highly reflective even up to a 90 degree angle
Quick and easy to apply

28002

Doorlec Flange Bearing F-360-13 5/8" (1.59cm) Hole

Fits model LJH/W

GALV-363-334-144-L

Torsion Spring .363 x 3-3/4" x 12ft LH Galvanized Green/White

Wire size: .363
Inside diameter: 3-3/4"
Length: 12 ft
Galvanized Stenciled

XP4040CUSH689

Heavy Duty Door Closer

Heavy Duty Door Closer with Spring Cush-N-Stop Arm

LB1212-18

Laminated Bumper Standard Black 12" L x 18" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

41D9044

LiftMaster Battery/ Logic Board Cover RJO

Compatible with 8500 and 8500W

.312_5-1/4"-LH

Torsion Spring .312 x 5-1/4" x 12ft LH Yellow

Wire size: .312
Inside diameter: 5-1/4"
Length: 12 ft

BK110/PR

Light Duty End Bearing Plate 3-3/8" with Bearing - EBF 338 Residential Sold as a Pair - LH/RH

With C16-32F bearing
Galvanized steel
3-3/8" shaft offset
Flange allows plate to be bolted to the wall for additional support
Same as part number 209

PRO-H-7543-U-RH

Micanan 3/4HP 460V 3P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

50690

Doorlec Clutch Assembly for ETBH

MV-00172

Micanan LCE-3 Nema-1 Pushbutton Control Station

Flush mount

MG00019

Micanan Flat Washer 13/16" ID x 1.5 OD (3/4" Shaft Size)

PRO-H/HB operator parts
2 required per operator

.234_1-3/4"-LH

Torsion Spring .234 x 1-3/4" x 12ft LH Blue/White

Wire size: .234
Inside diameter: 1-3/4"
Length: 12 ft

380LMC

LiftMaster Remote Work Light

For use exclusively with the LiftMaster Wall Mount Garage Door Opener (model 8500)
Provides 200 watts of light with adjustable light time delay
Lights are controlled by opener activation or control panel light button
Add as many lights as you wish – perfect for brightening up a dark garage or workspace

Installation Manual Manuel d'Installation Troubleshooting

CP-MO-12-115/1

Lynx Electric Motor 1/2 HP 115V 1 Ph *** NLA

Electric motor only

LVB620-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

MHS5011U-RH

LiftMaster 1/2 HP 120 Volt Medium Duty Slow-Speed Jackshaft Operator

Designed for use on rolling sheet doors.
It features an adjustable friction clutch high-starting torque motor with overload protection emergency chain hoist with electric interlock and emergency disconnect chain.
Easy emergency manual operation using a floor level disconnect and an electrically interlocked chain hoist mechanism
Floor level disconnect
24V NEC Class 2
Wiring is factory present to C2 mode

.......more details

Installation manual Sell sheet

25-42-260

Extension Spring 7' Door - 260 lbs Brown w/ clip

Double - Loop end for strength
25" long 42" stretch 260 lb load
Sold individually
Rated for 10000 cycles

K75-19985

LiftMaster Clutch Pulley Assembly

Fits model H operator with Logic 5

MS00005

Micanan Trolley Track 12-ga 14'-6" L Per Set ( Includes 2 Angles Only)

Track only- no chain or hardware

.225_2"-LH

Torsion Spring .225 x 2" x 12ft LH Orange/Green

Wire size: .225
Inside diameter: 2"
Length: 12 ft

.406_3-3/4"-LH

Torsion Spring .406 x 3-3/4" x 12ft LH Blue/Yellow

Wire size: .406
Inside diameter: 3-3/4"
Length: 12 ft

65_52091-14

LiftMaster Manual Hoist Mod. M8 #41 Chain for 14ft High Door

For 3/4 Hp & 1 Hp Trolley operators
Includes floor level brake release cable 1" x 12' round bar.

Installation Manual

811LM

LiftMaster 1-btn Dip-Style Transmitter Sec+ 2.0 ***No Longer Available

Extreme range 1-btn encrypted DIP style remote control.
Easy to code 12 position dip switch offers up to 4 096 codes.
NOT compatible with the new Liftmaster 8550 and 8360 garage door openers.
Compatible with the 850LM Universal Receiver.

Programming Instructions Instructions de programmation Sell Sheet

.306-258-R-C

Cut-to-Length Torsion Spring .306 x 2-5/8" Right Hand Wound Coated ** Price by Quote Only

Priced per inch
For factory installed cones priced seperately - use part no. C-258-INSTALLED

CP-CRG-OLD

Lynx Auto Re-Connect Carriage 20-1/2" Arm Sold Separately *** Discontinued

Will work on most brands of commercial trolley operators using 2" angle tracks.

.262-334-L

Cut-to-Length Torsion Spring .262 x 3-3/4" Left Hand Wound Red/Yellow

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

MOUNTSHAFT015

Manaras Hoist Shaft Kit for OGH

EHJ-353-1

Doorlec Industrial Jackshaft Op. 1 HP 575V-3Ph

Heavy-Duty Industrial Operator for Sectional or Rolling Steel Doors
DC-2000 logic with adjustable Timer To Close Delay On Reverse and Traffic Light Control
Solenoid Brake prevents coasting and secures the door when closed
TEFC (sealed) continuous-duty electric motor with overload protection
Automatic Friction Clutch protects the door and operator
Self-aligning Heavy Duty sealed Pillow Block bearings on all shafts for high cycle applications

.......more details

MD00420

Micanan Flex Coupling Lovejoy 3J x 3/8"

1016-ADHESIVE

Adhesive for Storm Shield 6oz tube

For use with 1016

Safety data sheet

1104-18FT-DK-BN

Residential Side & Top PVC Weather-Strip with cap 18' Long - Commercial Brown (DN)

Commercial brown rigid vinyl retainer with commercial brown flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Full case quantity only (12).

PRO-GH-10081U-L

Micanan 1 HP 208V 1P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

7001-WG-10-CO

Residential Wood Grain Side & Top W/S Cherry Oak 10' Long - Painted Screws to Match

Cherry Oak retainer with Cherry Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

.225-2-L-C

Cut-to-Length Torsion Spring .225 x 2" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

OPH-6114-M-N1-RH

Manaras Opera-H 1 HP 120V 1Ph Monitored Board w/N1 Eyes RH

A heavy-duty industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a self-engaging chain hoist for manual operation
Clearence: side room required 15"

1104-7FT-WHITE

Residential Side & Top PVC Weather-Strip with cap 7' Long - White (W)

White rigid vinyl retainer with white flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

2376.177_27.830

Whiting Torsion assembly .177 wire size 27" spring length 83" shaft

K20-1050B-2LP-H24

LiftMaster Electric Motor 1/2 HP 115V 1Ph Logic 3 Logic 4 Logic 5

Standard 1/2 hp motor for new L5 operators

EHJW-383-3/4

Doorlec Ind Jackshaft Op. Watertight ECB 3/4 HP 208V-3Ph

Equipped with: 3-btn control Adjustable Automatic Friction Clutch Emergency Chain Hoist and Heavy-Duty Solenoid Brake.
With DC-2000 controller
Watertight and Dust Tight EEMAC Type 4/12

K004-KEY

Replacement Key for 3BXLT Key #4

Replacement key only for key #K004

7001-14-CREAM

Commercial Side & Top Weather-Strip 14' Long - Cream (C)

Cream galvanized steel with cream dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Also known as Almond
Full case quantity only (10)

.218-2-R-C

Cut-to-Length Torsion Spring .218 x 2" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

1006-1-3/8-14'

Rigid Vinyl Bottom Retainer U-Shaped 14' Long

Black with flexible fin to touch door face.
For door thickness 1-3/8"

26-94322

Truck Door Bottom Panel with Seal (12" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood. Primer Finish
Comes only with bottom retainer and seal (installed)

620-101416

Linear GTO Alarm 24VDC Non-Pulsed Apex

1006-1-3/8-16'

Rigid Vinyl Bottom Retainer U-Shaped 16' Long

Black with flexible fin to touch door face.
For door thickness 1-3/8"

MK500GS

LiftMaster MiniKey Stand-Alone Keypad System ** No Longer Available

Self-Contained Keypad System for Door and Gated Entrances
500 Code capacity
Grained stainless steel Surface Mount
Dimension: 4-1/2" H x 4-1/2" W x 3-1/2" D
Same as SN7000255
Sentex Keypad

.......more details

Installation Instructions Programming Instructions Sell sheet

LMPK3-ST

LiftMaster HID ProxKey III 1346 Key Fob Price Per Fob

HID 26 Bit Format
125 kHz
Sold in Lots of 100 - Price Shown is Price per Card
Small enough to fit on a key ring
Universal compatibility with HID proximity card readers
Provides an external number for easy identification and control

.......more details

218954-03

Linear Pulley & Bracket Assembly - Belt (HBT)

050ACTWFATS

LiftMaster Receiver Logic Board AC WiFi for ATSW

050ACTWFATS is a Receiver Logic Board featuring Wi-Fi® with myQ® technology.
For use with LiftMaster® Model ATSW AC Chain Drive Light-Duty Commercial/Residential Door Operators; manufactured after 2018.
Unit will feature a yellow learn button

.283-2-RH-C

Torsion Spring .283 x 2" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .283 ID: 2" Length: 12 ft

M3-3313

Marantec 3-Button Transmitter 315 MHz 97245 ** Discontinued

Same as part # 65894 97245
Includes battery CR2032
Made in Germany

Instructions

2200-938

Linear VBelt 28 4L Cogged

26-945215

Truck Door Intermediate Panel (11.5" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish

TDC1222-20

Liftmaster Comm. 20FT Trolley Angle set (10-5820-P x 2) and #41 chain pack (TDC41-20) and spacer pad (71-10324***Actual length 275"***

Double Angle Rails for doors up to 20'6" high
Includes #41 chain pack and Spacer pad part # 71-10324

206-5017

Blue Giant Side Weather Seal 58"Auminum/Rubber Fits 6ft Dock Set of 2 *** Price by Quote Only

Gaps of up to 1" (25mm) can exist between the pit wall and the dock leveler sides
58" long weather seal made to fit 6ft dock leveler

RGHW-6214-MON-L

Manaras 1 HP 240V 1Ph Rapido Gear Head Carwash Mod Monitored ECB w/Eyes Left Hand

Rapido version of model OGHW
Includes Monitored Waterproof photocells

026-M12-F5

Blue Giant Cable M12-4 5M Female Leads

5 Meter Cable for Proximity Sensor

026-G019

Blue Giant Proximity Sensor M30 M12 Connector

(30mm Unshielded) Home/Lip Sensor

20111

Doorlec Cam Retainer Plate Springs *** Replaced by 26117

Works on GH/GHX

26130

Doorlec Hoist Shaft Threaded 5/8" x 12" GH/GHX

Works on GH/GHX

TXTA-KYPD

Pulse Universal Wireless Keypad

Programmable 4-digit code for continuous use.
Programmable TEMPORARY 4-digit code for programmable number of uses.
Multi-Brand Adaptable: Works with all Pulse receivers LM receivers (GreenOrange Red Purple and Yellow learning codes) and other receivers with 315MHz or 390MHz.
Powered by 9V battery. (One included in package)

BPPN17510

Garex Bottom PVC Moulding Black for 1 3/4" Door U shaped 120" (10')

026-122

Blue Giant Heater Element **Special Order

Price by Quote Only

SA1929/A18

Automatic Systems Feig Double Channel Loop Detector BL229

For AS1620 BL229

E/1929/025

Automatic Systems Bumper and Limit Switch Ass'y (BL229)

Used on the BL229 gate op.

1326-112-BLK-PLEXI

Elton Commercial Window 1-1/2" thick 1326 Black Frame Sealed Plexi Glass

Screw together window kit
Frame size: 26-1/8" x 13-9/16" (Tip to Tip)
Cut-out size: 25-1/16" x 12-9/16"
Vision area: 23-7/16" x 10-13/16" Corner Cut 4" Radius
Different glass options and frame colours are available upon request

1676.98

Whiting Bottom Seal 96" for 1801 U-Channel ** Price by Quote

Special order item. Price by quote only

1-1785

RW Spring Bolt 514 x 2

Housing: Cast iron 5-1/2" H x 2-7/8" W
Bolt: Cast iron bevelled
Keeper: Surface mount
Chain: Zinc plated 36" long with ring Finish: Zinc plated

OTBH-6532-AM05

Manaras Trolley Operator 1/2 HP 600V 3Ph Monitored Board w/N4 Eyes Apt. Model

The Silencio model is a low headroom apartment type operator designed for use on industrial standard lift sectional doors with high daily use requirements
100 cycles per day
It incorporates a drum-shoe type solenoid brake.
Tracks are an extra 36 lbs per track
#41 full roller chain
Includes monitored N4X eyes (PHOTO 061)

.......more details

K94-36992

LiftMaster Brake Cable Harness 1PH L5

Compatible with various LiftMaster® Logic 5.0 Commercial Gate Operators

K41-0071-000

LiftMaster HD Power Board Service Kit for HDSL24UL/HDSW24UL

Compatible with the following models: HDSL24UL HDSL24ULMC HDSW24UL HDSW24ULMC

10TD900PB

BEA Wired Transmitter 900mhz Flagged Flag Connectors AAA Battery

Multi-colour LEDs on receiver provide installer with visual notification of signal strength and activation status.
Frequency: 908-918 MHz
Radio Control Type: Digital
Programmable Capacity (standard): 75/unlimited universal
Operating Temperature: -10-55C

7-6093

RW Bottom Cane Bolt 524 x 2 Zinc Plated

Zinc plated

487135

Bircher Easy Loop Bracket

Bracket for part #487132

PRO-HBH-7511U-R

Micanan 3/4HP 115V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand (Pro-HHD)

3/4 HP115V 1PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

3-5273

Serco Pusher Assembly AB1000

MX001100

HySecurity Crankshaft w/Crank Bearing Zerk for StrongArm

Compatible with StrongArm systems
Includes crank pin bearing and zerk fitting
Two key stock for secure arm mounting
Supports smooth and efficient gate operation

MX000585-0

HySecurity Smart Touch Controller Board

Easy Installation Configuration
Warning Buzzer and Alarm System
Ethernet Connectivity via HyNet Gateway
Security Monitoring and Breach Reporting
Allows for the configuration of over 70 different settings for a reliable and highly customized gate operator

MX001777

HySecurity Limit Switch D2VW-5L3-1HS

Switch type: mechanical limit switch
Model: D2VW-5L3-1HS
Activates on contact to trigger gate control logic
Sealed housing for environmental resistance

02-401M

LiftMaster 1-Button Control Station

For use with various LiftMaster® Logic 4.0/5.0 and MAXUM Series Commercial Door Operator Applications
Sends the door to the full open position. Perfect for time sensitive situations.

7909212

FAAC Control Panel Main Circuit Board for FAAC 844

111-1899

RW End Blind/Cover 31 track Sold Individually

Covers the end of the track to help keep out dirt and debris

F210B

NICE Adjustable Synchronised Photocells w/Blue BUS Technology Sold as a Pair

Pair of synchronised Photocells with built in transmitter for 8k2 resistive safety edges.
Transmitter is powered by one 3.6 V battery.
Receiver with BUS Connection.
210 degrees horizontal adjustment and 30 degrees vertical.
F210B can only be connected to 'BlueBUS' networks

OSH-6433-M-N1-RH

Manaras Opera-SH 3/4HP 480V 3Ph Monitored w/ N1 Eyes Right Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation brake and a floor level engaging device
Clearence: side room required 16"

OSH-6433-M-N1-LH

Manaras Opera-SH 3/4HP 480V 3Ph Monitored w/ N1 Eyes Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation brake and a floor level engaging device
Clearence: side room required 16"

K15-48B18AXX

LiftMaster Sprocket 48B18T 3/8" Bore

Sprocket for #48 chain
Also known as: 15-9014 G159014 15-48B18AXX 159014

GHX-311-3/4HP-RH

Doorlec Explosion Proof Gear Head 3/4 HP 120V 1PH ECB Right Hand

Nema 7/9 control box
Electrical connections from motor to control box consists of hazardous location certified fittings
NEMA 7/9 O/C/S push-button station included

PDC300-12-1-40-20

Pulse300 Direct Drive Opener 1/2 HP 110/240V 1ph 1" Shaft 40:1 20' Cable ** Price by Quote Only

Advanced speed control: up to 24"/s opening up to 16"/s closing
Built-in 24V 9Ah battery backup
Soft start/stop functionality
Universal single-phase power compatibility: 110-240V 50/60Hz
Adjustable force monitoring
Programmable closing timer: 1-99s A high-performance direct-drive door operator with a 90V DC horsepowerrated motor engineered for balanced commercial and industrial doors

.......more details

MM00310

Micanan Sliding Door Carriage

Fits model GSD

MG123-BLACK-NM-U

Miller Edge Black Non-Monitored Universal Outlet 2 -Wire 2" wide x 1-1/2" high Sold by the Foot

The MG123 sensing edge is identical to the ME123 in shape and dimensions
The only difference is the rubber compound softer which makes it a bit more sensitive than ME123 (4-7 lbf vs 6-11 lbf).
Easy to install
Optimum size for 2 inch gate surfaces
Double-T design for added stability
Mounts vertically or horizontally

.......more details


User Name:
Password:
Remember Me:

	Forgot your password
Request a Login