Devanco Canada - Get The Right Garage Door Opener‎ and Parts

SBB-3

3" Safety Bottom Bracket Low Tension Sold as a Pair Torque Force

Includes 1-Right hand and 1-Left hand
Zinc plated Steel
Max Door Weight: 2200 LBS
Cable attachment: Fixed
Protective cover: No
Use with: Straight track 3"
Panel thickness: 3/4" minimum
Cable diameter: 1/4" max

Installation instructions Instructions d'installation Spec sheet

44-30703

LiftMaster Enclosure SL595

Replacement SL595 Enclosure
Also known as: 44-18491

BK111/PR

End Bearing Plate Flanged Heavy Duty 8-GA 3-3/8" without Bearing. Sold as a pair

They have 4 slots surrounding the hole to accommodate a regular bearing (with flange).
A pillow block bearing could be used if needed
Includes (1) RH and (1) LH plate

E/1929/071

Automatic Systems Round Arm Ass'y 16'-5" (BL229)

Used on the BL229 gate op.

30004

Doorlec Brake Solenoid 460V with wire leads

22010

Doorlec 1-22mm Cylinder Complete with Normally Open Contact Spring Return Includes 2 keys

2100-564

Linear Clutch Disk Facing HSL HSLG

MA041

LiftMaster Mega Arm Tower Lock & Keys (No Dust Cover)

Comes with two keys

RADIO-RE901A

Manaras 1-Channel 24V Dip-Switch (313MHz) & Rolling Code (390MHz) Receiver with Commercial Antenna

For Commercial/Industrial Garage Door Applications
Wall Mount
DIP Switch and Rolling Code Technology
Sixteen (16) Fixed Codes / Receiver
313 MHz & 390MHz Radio Frequency
Controls One (1) Door

.......more details

Programming instructions

SPRING040

Manaras Disconnect Spring

12501

Doorlec Clutch Plate Aluminum 4" dia x 1" bore

Works with models EHJ and ETBH

HAE00012

Linear Motor Cover LDO50

Replacement motor cover only

112561

Allstar MVP-RE 24V 8 Wire Receiver 288 MHz *** NLA

Three channels – three relay outputs
8-wire operator connection
Wire whip antenna with “F” connector
Compatible with Allstar Classic Allister and Pulsar dipswitch transmitters and MVP quik-code transmitters
Power: 24 VAC/VDC
Codes: 19683

.......more details

10-10191-GR

LiftMaster Brake Disc

For various Liftmaster commercial slide door operators
Also known as: 10-10191-GR 10-10191-GR 1010191 G105209 10-10191 105209

VMD202-50

EMX Vehicle Motion Detector Probe with 50ft Lead Wire

The VMD202 Vehicle Motion Detector is the most advanced single-piece vehicle motion sensor on the market today.
The probe and its electronics are housed in a slim design that is buried next to a driveway.
The VMD202-R Sensitivity Remote Control (sold separately) makes installation and fine tuning simple
Probe assembly and wire are water tight and direct burial compatible
Harness is pre-wired onto lead wire for easy installation
Settings are placed in a non-volatile memory in case of power failure

.......more details

LZE500

Erone L & Z-Bracket for Maglock ESM500

T-831

FL-Allstar Stationary TransmitterO/C/S 3-Btn 1-Door 311 MHz 107483

Open/Close/Stop stationary remote for 1 door.
Designed for commercial automatic door and gate operator applications.
This transmitter can operate a single receiver connected to one operator
Compatible with 3-channel Allstar and MVP receivers
Easy access to battery and coding switch
Power: 9-volt battery

.......more details

41A7618

LiftMaster End Panel with Battery Cover and Light Socket 8550W

BEARING006

Manaras Flange Sealed Bearing 5/8"

Flange sealed bearing for 5/8" shaft

CP-SH-58-1012

Lynx Center Shaft Only for MCJH 5/8" x 10-1/2"

WA10

NICE Red Adhesive Reflector Strips 24pcs/Pkg

SPGAP06400A

NICE Replacement Nylon Insert Kit

MX00128

Micanan Clutch Assembly for PRO-GOHD

30001

Doorlec Brake Solenoid 575V with wire leads

PTRR5-C

Telco Light Curtain Fastening Clips 3 pcs/Bag

DHJ501L5-LH

LiftMaster Ind. Duty Hoist/Jackshaft Op. 1/2 HP 115/230 VAC Logic 5 Left Hand***Discontinued

Industrial-Duty Hoist/Jackshaft Operator with Internal Door Lock Sensor
Optimal for shopping mall applications with heavier rolling doors and grilles.
Provides a floor level chain hoist to ease manual operation in an emergency or power outage.
Includes a door lock sensor to prevent damage to the door and operator caused by attempts to automatically open a locked door.
Industrial Ball Bearings on 1" Output Shaft
Second Floor-Level Disconnect for Manual Lifting in an Emergency

.......more details

50690

Doorlec Clutch Assembly for ETBH

HW-SP-BL

Lynx Disconnect Spring

CAM017

Manaras Synthetic Disconnect Cam Opera

L-14-50-0-D

Cable Tie Standard 50 LB Black 14" Nylon 500/pkg

Ultraviolet Resistant
Length: 14.56" / Width: .180" / Thickness: .052" / Diameter: 4.125"
Low insertion and pull through force
Advanced pawl and teeth design
Angled tail provides quicker initial insertion alignment
Tail finger grips allow easier handling and tightening

.......more details

37380

Doorlec Auxiliary Contacts BF9 Contactor

H-0168

Autogate VBelt Banded B-66

New Style Double Reduction

VPL-12

Autogate 12V Motor

MOUNTSHAFT018E

Manaras Limit Shaft Kit For Damp/Corrosive Env.

For operators with W or C Modification

K72-13912

LiftMaster Clutch Shaft Kit T GH

41D0277-1

LiftMaster Transformer WiFi Battery Backup

For Wi-Fi Battery backup garage door openers; manufactured after 2011
Same as #204D0277-1

K1D8389-1CCU

LiftMaster Upgrade Kit with Eyes DC Pad Mount for UL325

Upgrade Kit for models CSW24V CSW24VH CSW24VDC CSL24V CSL24VH and CSL24VDC UL325 Approved Gate Operators; manufactured 2012 to 2015.
Complete kit includes: Main Control Board Expansion Board LiftMaster® Monitored Retro-Reflective Photoelectric Sensor Kit UL Upgrade label and Adapter Harness (used with CSW24V CSL24V and CSL24VH only)

SGP-321-1-230/1

Doorlec Gate Master 1 HP 230V 1 Phase with Heater and Lights in Cabinet

Post mount heavy-duty industrial slide gate operator
Max. gate weight: 2500 lbs
Gate travelling speed: 45 ft / minute
175 watt heater included

31104

Doorlec Sprocket 41B23-5/8"

883LMW

LiftMaster Door Control Bell Button Wi-Fi

Controls garage door operation and garage door opener lights
On-board programming capability makes it easy to program remote controls and MyQ® enabled accessories
Compatible only with Security+2.0™ LiftMaster® garage door openers enabled by MyQ® technology
Note: If your door control has an image of a light bulb above the light button with 3 wavy lines above it the door control is capable of placing a Wi-Fi Garage Door Opener into Wi-Fi Learn mode.

Q028

LiftMaster Manual Crank for SL3000 (K07-50303) **DISCONTINUED

Hand crank for SL3000

PRO-SD-10011-U-RH

Micanan 1 HP 115V 1P Horizontal Sliding Door Op. Monitored ECB N1 Eyes Right Hand

Designed for use on commercial / industrial sliding doors or sliding fire doors
External radio control terminal strip
3-btn O/C/S control station Nema 1
#41 roller chain & sprockets on all internal drives
Heavy duty 5L v-belt
Solenoid brake standard

.......more details

PRO-SD-10011-U-LH

Micanan 1 HP 115V 1P Horizontal Sliding Door Op. Monitored ECB N1 Eyes Left Hand

Designed for use on commercial / industrial sliding doors or sliding fire doors
External radio control terminal strip
3-btn O/C/S control station Nema 1
#41 roller chain & sprockets on all internal drives
Heavy duty 5L v-belt
Solenoid brake standard

.......more details

1005-1-1/2-14'

Aluminum Bottom Retainer U-Shaped 14' Long

For door thickness 1-1/2"

FEP100N

Pneumatic Safety Edge End Caps Included Sold by the Foot

Must specify if L-retainer is required

K32-37560-3

LiftMaster Gear Reducer 28:1

This is a replacement Gear Reducer (28:1). Compatible with LiftMaster® HCTDCU Overhead Gate Operators.

510.2996.07

Whiting Steel Roller Upgrade Option for 7 Panel DF Door

Upgrade option only - must accompany a door order

C-26-1/2X14-134-W

Thermal Window 26-1/2" x 14" for 1-3/4" Cedo Door White

For 1-3/4" thick door

ME00054

Micanan Clutch (Input) Shaft Only for Pro-H/HHD N4 3/4" x 17-5/8" (3/4 HP-1 HP)

3/4" x 17-5/8"

C-26-1/4X14-134-W

Thermal Window 26-1/4" x 14" for 1-3/4" Cedo Door White

For 1-3/4" thick door

MOTOR258

Manaras Electric Motor TEFC 3/4HP 120/240V 1PH

C184-24B

Coil Cord 4 Wire 18-Gauge Black Extends 24ft

2500-1980

Linear 3-Phase Motor Board

Motor board for "green board" generation OSCO gate operators.
For HSLG BGU GSLG VS-GSLG SLC and their variants

PRO-APTC-5083-U

Micanan 1/2HP 208V 3P Apartment Trolley Op. Photo Eyes Monitored ECB

Low clearance design for APT applications (8.5")
Door speed: 7" per second
N-4 Micanan compatible monitored photocells included
Monitored board
Side access hinged cover for easy access to controls
Three button open-close-stop control station Nema-1

.......more details

Installation manual

TRMC38E

Telco Light Curtain Bracket 4/pkg

33102

Doorlec Overload 1.20 to 2.00 Amps

PRO-GHC-10053U-L

Micanan 1 HP 575V 3P Gearhead Operator with N1 Eyes Monitored ECB Left Hand

External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation
Full function Smart 10.0 logic board and on-board receiver

.......more details

CP-SH-58-1038-HDC

Lynx Complete Limit Shaft Assembly for HDC

5/8" x 10-3/8"
Same kit used for MCJH except the HCT has 1 extra nut

MG020-B-2E-03

Miller Edge Sensing Edge Black 2-Wire End Outlet 3 ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

SPRAY-431

Aluminum Touch Up Spray Paint 350g Bright White / Blanc Pur #431

350g
Replaces Gentek #801

20104

Doorlec Coupling Spring 5/8" LJH

26CW94623-CUT

Truck Door Top Panel Painted White (13" x Cut-to-Size) for Whiting DryFreight

These panels are cut to an extra wide width to fit wider vehicle applications
Interlocking tongue and groove design for weather-tight joint and proper alignment.
Non-routed
.75" thick 7 ply exterior grade medium density plywood
Painted white

OSH-6212-ECB-LH

Manaras Opera-SH 1/2 HP 240V 1Ph with Electronic Circuit Board Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"

Installation Manual

ALUM-5P5

Aluminum 24" x 100' Spool Graphite # 5P5

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 5P5
Reverse side is #431 Bright White

Colour chart

93D341

LiftMaster Cover Only Silver for EL25

Also known as 041D0341 41D341
Replacement cover for EL25

MOTOR272

Manaras Electric Motor 1/2HP 600V 3PH

Continuous-duty base mount ODP 60Hz •This item is compatible with BRAKE011

PRO-GH-7543U-R

Micanan 3/4HP 460V 3P Gearhead Operator N1 Eyes Monitored ECB Right Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-GH-7523U-R

Micanan 3/4HP 230V 3P Gearhead Operator N1 Eyes Monitored ECB Right Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-X_MOD-5HP

Micanan Explosion-Proof Modification N-7/N-9 for 5HP

Modification includes an explosion-proof motor explosion proof fittings operator mounted explosion-proof electrical control enclosure and n explosion-proof three button station.

PRO-4X_MOD_3HP

Micanan Nema 4X Modification 3HP

This modification provides a washdown motor N-4X corrosion proof stainless steel control box enclosure waterproof drive and limit chain and a corrosion proof three-button station.
For options M & U Micanan N-4X photocells are supplied
For 3HP motors

K1D7078

LiftMaster EMI Board

This is a replacement EMI Board. Compatible with LiftMaster® Model HCT Overhead Gate Operators

.437-514-R-C

Cut-to-Length Torsion Spring .437 x 5-1/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.437-6-R-C

Cut-to-Length Torsion Spring .437 x 6" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED

.393-6-L-C

Cut-to-Length Torsion Spring .393 x 6" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

.406-514-L-C

Cut-to-Length Torsion Spring .406 x 5-1/4" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-514-INSTALLED

.363-514-L-C

Cut-to-Length Torsion Spring .362 x 5-1/4" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold separately
For factory installed cones use part no. C-514-INSTALLED

.343-334-R-C

Cut-to-Length Torsion Spring .343 x 3-3/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

.331-258-L-C

Cut-to-Length Torsion Spring .331 x 2-5/8" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.319-334-R-C

Cut-to-Length Torsion Spring .319 x 3-3/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-375-Installed

.319-258-R-C

Cut-to-Length Torsion Spring .319 x 2-5/8" Right Hand Wound Coated ** Price by Quote Only

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-258-Installed

.283-2-L-C

Cut-to-Length Torsion Spring .283 x 2" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.250-2-R-C

Cut-to-Length Torsion Spring .250 x 2" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.243-258-R-C

Cut-to-Length Torsion Spring .243 x 2-5/8" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.243-258-L-C

Cut-to-Length Torsion Spring .243 x 2-5/8" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.225-258-R-C

Cut-to-Length Torsion Spring .225 x 2-5/8" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.207-258-L-C

Cut-to-Length Torsion Spring .207 x 2-5/8" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.207-2-L-C

Cut-to-Length Torsion Spring .207 x 2" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

PRO-GH-7521U-L

Micanan 3/4HP 230V 1P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

2807.148.180

Whiting .148 x 2-3/16 x 18" Curbside with Cones

218758

Torque Force Spring Failure Device 1-1/4" Shaft Left Hand Side

For springs 2" up to 6"
This device can be applied on Industrial OH doors that are manual or motor operated
Must be installed on a keyed shaft

PRO-GH-5053U-L

Micanan 1/2HP 575V 3P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-GH-5043U-L

Micanan 1/2HP 460V 3P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-GH-5023U-R

Micanan 1/2HP 230V 3P Gearhead Operator N1 Eyes Monitored ECB Right Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

91568

Marantec Sprocket Holder Assembly for Chain Rail *** NLA No Replacement

Compatible with Marantec Chain Standard Rail.
Same as #8030339 (old part number)

PRO-GH-5023U-L

Micanan 1/2HP 230V 3P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-GH-5083U-L

Micanan 1/2HP 208V 3P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-GH-5081U-R

Micanan 1/2HP 208V 1P Gearhead Operator N1 Eyes Monitored ECB Right Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-HHD-10043U-R

Micanan 1 HP 460V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand

1 HP460V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details