Devanco Canada - Get The Right Garage Door Opener‎ and Parts

PRO-J-10081-U-LH

Micanan 1HP 208V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft
Emergency disconnect with electrical cut-out switch for manual operation
Three button open-close-stop control station Nema-1
#41 roller chain & sprockets on all internal drives
#50 roller chain and sprockets on final drive
1" permanently lubricated & sealed ball bearings on final drive shaft
External radio control terminal strip

Specification Sheet

PRO-J-10011-U-RH

Micanan 1HP 115V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-10011-U-LH

Micanan 1HP 115V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Installation Manual (EN) Specification Sheet

.421-6-L

Cut-to-Length Torsion Spring .421 x 6" Left Hand Wound Gold

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

.421-514-R

Cut-to-Length Torsion Spring .421 x 5-1/4" Right Hand Wound Gold

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-514-INSTALLED

.437-514-R

Cut-to-Length Torsion Spring .437 x 5-1/4" Right Hand Wound Red/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.406-514-L

Cut-to-Length Torsion Spring .406 x 5-1/4" Left Hand Wound Blue/Yellow

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-514-INSTALLED

.406-334-L

Cut-to-Length Torsion Spring .406 x 3-3/4" Left Hand Wound Blue/Yellow

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

.406-334-R

Cut-to-Length Torsion Spring .406 x 3-3/4" Right Hand Wound Blue/Yellow

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

.343-258-L

Cut-to-Length Torsion Spring .343 x 2-5/8" Left Hand Wound Blue/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.331-258-R

Cut-to-Length Torsion Spring .331 x 2-5/8" Right Hand Wound Red/White

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.331-258-L

Cut-to-Length Torsion Spring .331 x 2-5/8" Left Hand Wound Red/White

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.319-514-R

Cut-to-Length Torsion Spring .319 x 5-1/4" Right Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-514-Installed

.319-514-L

Cut-to-Length Torsion Spring .319 x 5-1/4" Left Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-514-Installed

.312-514-R

Cut-to-Length Torsion Spring .312 x 5-1/4" Right Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.306-514-R

Cut-to-Length Torsion Spring .306 x 5-1/4" Right Hand Wound Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.306-514-L

Cut-to-Length Torsion Spring .306 x 5-1/4" Left Hand Wound Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.283-6-R

Cut-to-Length Torsion Spring .283 x 6" Right Hand Wound White

Priced per inch
For factory installed cones priced seperately - use part no. C-600-INSTALLED

.243-334-L

Cut-to-Length Torsion Spring .243 x 3-3/4" Left Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

.243-334-R

Cut-to-Length Torsion Spring .243 x 3-3/4" Right Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

PRO-J-7553-U-LH

Micanan 3/4HP 575V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

.375-334-L

Cut-to-Length Torsion Spring .375 x3-3/4" Left Hand Wound Yellow/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

PRO-J-7523-U-LH

Micanan 3/4HP 230V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

ME117-2W-BLK-U

Miller Edge 2-Wire Black Universal Outlet Sold by the Foot

Electromechanical slide in edge for 1" to 2" sectional doors.
Touch sensitive signaling allows for immediate stopping or reversing of motion. The ME117 is resistant to water flame and most common greases and oils.
Temperature range: -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Installation manual Sell sheet

PRO-J-7583-U-LH

Micanan 3/4HP 208V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-7521-U-LH

Micanan 3/4HP 230V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5053-U-RH

Micanan 1/2HP 575V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5043-U-RH

Micanan 1/2HP 460V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5043-U-LH

Micanan 1/2HP 460V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5021-U-LH

Micanan 1/2HP 230V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5081-U-LH

Micanan 1/2HP 208V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5011-U-RH

Micanan 1/2HP 115V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

BCH755L5-LH

LiftMaster Hoist Op. with Carwash Mod. 3/4 HP 575 VAC 3 Ph L5 Left Hand ***Replaced by CRBH755L5-LH

Industrial Duty Hoist Operator with Damp Environment modification
Comes with CPS-UN4 photoeyes
External brake included

PRO-LJ-5021-U-LH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

PRO-LJ-5011-U

Micanan 1/2HP 115V 1P Jackshaft N1 Eyes Monitored ECB Universal Mount

On-Board receiver holds up to 20 transmitters

PRO-LJ-5011-U-LH

Micanan 1/2HP 115V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

PRO-GT-10023-U

Micanan 1HP 230V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

MA026

LiftMaster Pad Only Yellow For 12' Arm

Pad only - arm not included

PRO-GT-7553-U

Micanan 3/4HP 575V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-7543-U

Micanan 3/4HP 460V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

SPRAY-5P6

Aluminum Touch Up Spray Paint 350g Iron Ore / Minerai de Fer #5P6

140g

SPRAY-468

Aluminum Touch Up Spray Paint 350g Nutmeg / Brun Muscade #468

350g can

K29-FDCL-500CCB

LiftMaster FDCL Receiver Logic Board with Battery Rev 500

Replacement kit charging circuit board firmware and battery for FDCL

ALUM-568

Aluminum 24" x 100' Spool Nutmeg / Brun Muscade # 568

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 565
Reverse side is #431 Bright White

Colour chart

.393-334-R

Cut-to-Length Torsion Spring .393 x 3-3/4" Right Hand Wound Orange

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

.406-6-L

Cut-to-Length Torsion Spring .406 x 6" Left Hand Wound Blue/Yellow

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

.319-258-L

Cut-to-Length Torsion Spring .319 x 2-5/8" Left Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-258-Installed

PRO-T-5038-U

Micanan 1/2HP 380V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-5043-U

Micanan 1/2HP 460V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board

60-7248-81111

Wheel Chock Safety Pkg incl'd: orange urethane chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) 811-11 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Not For Use on Ice
High Visibility
Orange Urethane
Size: 11" wide x 8" long x 8" high

60-7248-888

Wheel Chock Safety Pkg incl'd: laminated chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) 88-8 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Fabric Reinforced Tire Rubber
Galvanized Steel Sides
Size: 8" wide x 8" long x 8" high

88-8

Wheel Chock 88-8 Laminated Rubber Galv. Steel Sides

Fabric Reinforced Tire Rubber
Galvanized Steel Sides
Size: 8" wide x 8" long x 8" high

88-8XL

Wheel Chock 88-8XL Laminated Rubber Galv. Steel Sides

Made From Used Truck Tire Laminates Compressed and Fastened Under High Pressure
Galvanized Steel Sides
Size: 11-1/4" wide x 14" long x 14" high

60-7248-CBI29

Wheel Chock Safety Pkg incl'd: cast ductile iron wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) CBI-29 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Made from Cast Ductile Iron for Impressive Strength
Painted Blue for good Visibility
Completely Reversible for Simple Use
Size: 8" wide x 12" long x 9" high

60-7248-CC07

Wheel Chock Safety Pkg incl'd: cast alum. alloy chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) CC-07 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Reversible Chock Design
One-Piece Cast Construction
Cast Aluminum Alloy
Size: 10" Base x 9" high x 6-1/4" wide

CC-07

Wheel Chock CC-07 Cast Aluminum Alloy

Reversible Chock Design
One-Piece Cast Construction
Cast Aluminum Alloy
Size: 10" Base x 9" high x 6-1/4" wide

MOTOR271

Manaras Electric Motor1/2HP 208/460V 3PH

This item is compatible with BRAKE011

27122

Doorlec Electric Motor 1/3HP 208/480/575V 3PH DC321

CGH755-L5

LiftMaster Gearhead with Brake and Carwash Mod 3/4HP 575V 3P L5

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting.
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

Damp Environment Modification

K23-30716

LiftMaster Stop Switch 120VAC 6A

Same as 20-30716

DM120-125-T/FORCE

Cable Drum High Lift 120" D575-120-1-1/4" Pair Torque Force

120" High Lift aluminum die cast alloy cable drums.
3/8"-16 x 2" hardened cup point set screws installed with red heads.
Pair includes: (1) LH and (1) RH. Color coded: Red=LH and Black=RH.
Maximum high lift: 120".
Maximum door height: 144" + High Lift.
Rated lift per drum: 500 lbs.

.......more details

MK-00033

Micanan Transformer 575V-24V-40VA

31D380

LiftMaster Sprocket Cover

Sprocket Cover Replacement Kit for use with various LiftMaster® and Chamberlain® Chain Drive Garage Door Openers

27-24416

Truck Door Dual Torsion Spring Assembly 96/33 for Whiting Roll-Up Doors

Assembly includes: shaft LH & RH springs winding cones cable drums with bearings and spring spacers.
Springs are treated with rust preventative
Roadside cable drum is color coded RED
Specs: Shaft Length: 96" Spring Length: 33" Wire diameter: .182 Winding cone color: Green

HRB-12

High Riser Bracket for 7" Above Dock or Higher 12"

High Riser 12" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

HRB-11

High Riser Bracket for 7" Above Dock or Higher 11"

High Riser 11" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

HRB-10

High Riser Bracket for 7" Above Dock or Higher 10"

High Riser 10" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

HRB-9

High Riser Bracket for 7" Above Dock or Higher 9"

High Riser 9" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

HRB-7

High Riser Bracket for 7" Above Dock or Higher 7"

High Riser 7" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

C-RING

Contact Ring for Centrifugal Switch in Single Phase Motor

MOUNTSHAFT010A

Manaras Hoist Shaft Kit for MJH (after-1998)

For MJH MJHW/C/X built from 1999-2003

MK01065

Micanan Light Duty Resistor 2 OHM 25W c/w Wire Leads

T

Molded Rubber Bumper Black 22" L x 10" W x 12" W 3" Projection Centered Reflector 3-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 3 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

B

Molded Rubber Bumper Black 24" L x 12" W 3" Projection 4-Hole 2 Reflectors Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 6 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

DBE-30

Molded Rubber Bumper Black 30" L x 4 1/2" W 3" Projection 6-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 6 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

DBE-20

Molded Rubber Bumper Black 20" L x 4 1/2" W 3" Projection 4-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 4 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

DBE-10

Molded Rubber Bumper Black 10" L x 4 1/2" W 3" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles molded bumpers will not warp rust rot or harden.
Bumper comes with 2 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts
10" L x 4 1/2" W 3" Projection

.......more details

LVB1224-11

Laminated Bumper Black 12" Projection Vertical Installation 24" L x 11" W Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

STRUT-2-1/4-9'-NH

Door Strut 2-1/4" Non Hemmed 9 ft Long *** To Extent of Inventory

Reinforcement bar 2-1/4"
20-GA

LB1212-24

Laminated Bumper Standard Black 12" L x 24" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1212-12

Laminated Bumper Standard Black 12" L x 12" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1210-24

Laminated Bumper Standard Black 10" x 24" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1210-36

Laminated Bumper Standard Black 10" x 36" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1012-14

Laminated Bumper Standard Black 12" x 14" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1012-12

Laminated Bumper Standard Black 12" x 12" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB912-36

Laminated Bumper Standard Black 12" x 36" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB912-18

Laminated Bumper Standard Black 12" x 18" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB910-24

Laminated Bumper Standard Black 10" x 24" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB810-36

Laminated Bumper Standard Black 10" x 36" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB436-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TVB420-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

Drawing

LVB436-11SF

Steel-Faced Laminated Bumper Black 4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TB412-24SF

Steel Faced Laminated Bumper Black 12" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB412-18SF

Steel Faced Laminated Bumper Black 12" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-24SF

Steel Faced Laminated Bumper Black 10" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-18SF

Steel Faced Laminated Bumper Black 10" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-14SF

Steel Faced Laminated Bumper Black 10" x 14" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB406-24SF

Steel Faced Laminated Bumper Black 6" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

STRUT-2-1/4-12'-NH

Door Strut 2-1/4" Non Hemmed 12 ft Long

Reinforcement bar 2-1/4"

LB412-24SF

Steel Faced Laminated Bumper Black 12" x 24" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details


User Name:
Password:
Remember Me:

	Forgot your password
Request a Login