Devanco Canada - Get The Right Garage Door Opener‎ and Parts

2235.296-CUT

Whiting Coldsaver Bottom Panel 14-1/2" x 94-3/4" with lock Topcoat Long Pull Strap & SS package

Fits Coldsaver Roll-Up Doors
1-1/8" thick 96" wide
Includes Lock and keeper

97-75004

DOT-C2 Reflective Tape 150 ft x 2" W 11" White x 7" Red Pattern

DOT-C2 certified exceeds NHTSA requirements
Highly reflective even up to a 90 degree angle
Quick and easy to apply

DGPROX

Erone 1-Door Stand Alone Card Reader / Keypad

500 users (proximity badges and/or codes)
3 operating modes: - Mode 0: badge and code - Mode 1: badge only - Mode 2: badge or code
Audible & Visual feedback
1 request-to-exit input
Tamper switch
1 form C door relay output (3A/125V)

.......more details

Programming Instructions Instructions de programmation Sell Sheet Wireless System Chart

1104-8'-DES-SAN

Residential Side & Top PVC Weather-Strip with cap 8' Long - Desert Sandstone

Garaga desert sandstone rigid vinyl retainer with Garaga desert sandstone flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

27-48-320

Extension Spring 8' Door - 320 lbs Green

Single - Loop
27" long 48" stretch 320 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

MP00021

Micanan Up-Charge Track and #410 (#48) chain for 24' h Door *Actual length 318"*

For 1/3 HP and 1/2 HP operators only

MP00016

Micanan Up-Charge Track and #41 chain for 16' h Door *Actual length 222"*

For 3/4 HP and 1 HP operators only

M003

Rolling Steel Groove Mouth GM679

B014

Rolling Steel 2" Flat Bar 5/16" Sold per Foot

17JW

Rolling Steel 2" Flat Cast Windlock

Windlocks are especially used on rolling steel doors and shutters to prevent "blow-ins" from severe storms or winds.
A wind lock is a small metal device that is attached to each slat.
Its primary function is to reduce the amount of friction that occurs between the actual door & the guiding panel.
When the wind is strong the roller door may be dislodged bent or misaligned from the guide.
With a windlock your door can operate efficiently despite wind load or pressure.
Windlocks are easy to add on to any existing rolling steel or shutter door

.......more details

2522

Whiting Thrust Washer

Used on Whiting balancer assemblies

SLT4-22

Rolling Steel 3" Crowned Slat 22-ga Galvanized

SLT4-20

Rolling Steel 3" Crowned Slat 20-ga Galvanized

SEL2641R433-IP5

Erone 2-Relay Stand Alone Receiver Up to 500 Users 433MHz

2 transmitter keys per user
1 NO relay + 1 NO/NC relay (24VA)
Self-learning memorization
12/24V AC/DC

Wireless System Chart

CARRIAGE006

Manaras Trolley Carriage Aluminum Die Cast

OTBH-6233-1-ECB

Manaras Trolley Operator 3/4 HP 208V 3 Ph with Electronic Circuit Board

Heavy-duty low headroom trolley operator designed for use on industrial standard lift sectional door
25 cycles per hour 80 cycles per day
It incorporates a drum-band type solenoid brake.
Tracks are an extra 36 lbs per track
3/4 HP & 1 HP operators come with #41 full roller chain

Installation Manual Sell Sheet

OSH-6433-ECB

Manaras Opera-SH 3/4 HP 480V 3 Ph with Electronic Circuit Board

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual Sell Sheet

87-P-075

LiftMaster Turac 3/4" Push on Fastener

CLUTCHPAD008

Manaras Clutch Pad 1" ID 4" OD

Replaces CLUTCHPAD002

OPJ-6232-ECB

Manaras Heavy-Duty Jackshaft Operator 1/2 HP 208V 3 Ph with Elect Circuit Board

An industrial operator designed for use on standard high and vertical lift sectional doors
Can also be used on rolling doors and grills
It incorporates a floor level disconnect mechanism for manual operation
25 cycles per hour 100 cycles per day
Continuous-duty single phase capacitor start or 3 phase motor open drip proof
Mechanical brake

.......more details

Installation Manual Sell Sheet

V1104-WHITE

Replacement Vinyl Only for 1104-White 200ft Roll

Sold in 200 ft rolls only

75W-RS-BULB

Rough Service Bulb 75W ** Disc. to extent of inventory

9150000629

3/16" Stops ONLY 100/pkg

Stops only 100 per pack

34538S.S

Genie Magnetic Close Down Limit Switch Assembly 138"

For Chain Glide models

18007

Doorlec Reducer BHC-63 5/8' or 7/8" Input

Gearbox for GH operator

BL229-ARM-12-R

Automatic Systems Aluminum Barrier Gate Arm 12 ft Round

774

Fasteners Hex Head Bolt 5/16-18 x 3/4" 1000/Box

5/16" bolt has 1/2" head
Max torque = 12
Full thread
Grade 2/Grade 5 depending on availability

775

Fasteners Hex Head Bolt 1/4-20 x 3/4" 1000/Box

1/4" bolt has 7/16" head
Max torque = 6
Full thread

RBH501L5-LH

LiftMaster 1/2 HP 115/230 VAC 1 PH Commercial Hoist Operator Logic 5 ***Use RBH751L5-RH***

With the addition of the 828LM MyQ technology enables the user to monitor and control their operator and light with their smartphone tablet or computer.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.
Security+ 2.0™ safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you.
Brake standard on all RBH operators
#48 chain #50 output sprocket chain
Comes with CPS-U photoeyes and 02-103 O/C/S push button

.......more details

Installation Manual Manuel d'Installation Sell sheet

Q400MAU

LiftMaster Relay Module

5X10SC50

Devanco Loop 5' x 10' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation Instructions Instructions d'installation Loop Placement Guide Guide de positionnement des boucles

41B4103

LiftMaster Service Belt Tensioner

K001D8075-1

LiftMaster Logic Board - L5 ** USE K001D8395

14D1279E

Programming Instructions Instructions de programmation

K72-14130-1

LiftMaster Limit Shaft Kit H J and HJ Logic 3 Logic 4 and Logic 5 commercial operators

For models H J and HJ Logic 3 Logic 4 and Logic 5 commercial operators
Kit includes: Limit shaft Limit nuts Limit bearings Limit sprocket Interrupter cup Shim washers Compression ring Roll pin and E-rings.

111854.0002

Overhead Logic Board for RSX 3/4 & 1 HP 1PH

Description: KITPCB1PH3/4-1HPSX/HXUL10
For RSX ad RHX models 3/4 & 1 Hp Single phase operators

71-REDGRN-HCT

LiftMaster Red/Green Warning Light Box **DISCONTINUED

Signals if door is moving or stationary
Compatible with model HCT

Installation Manual

K75-10177

LiftMaster Brake Hub Assembly

Assembly includes: Brake hub set screw push-on fastener and feather key

K20-1075B-2LP

LiftMaster Electric Motor 3/4 HP 115/230V 1PH L3 L4 *** NLA Replaced by H24

Standard 3/4HP 115V Logic 3 or L4 model T J HJ SD & H

41C2735

LiftMaster Chain and Cable Assembly CMC84

Fits a Sears Craftman CMC84 operator

EL25G

LiftMaster Telephone Entry System Gray

Capable of accepting up to 2000 codes
4 assignable and programmable built-in relays
Mounting versatility and available in 3 colors: Gray Nickel or Silver

Installation Manual Sell Sheet

M3-3313

Marantec 3-Button Transmitter 315 MHz 97245 ** Discontinued

Same as part # 65894 97245
Includes battery CR2032
Made in Germany

Instructions

22405-KEYLOCK

Doorlec Weatherproof Pushbutton O/C/S Key Lock with On/Off Switch

22-00626

Truck Door Grab Handle 13" Zinc Plated ** This is no longer available

Steel construction Zinc plated
Cross ref: Eberhard 4300

08-11012

LiftMaster Bevel Gear 5/8" ID

Fits LiftMaster GH operator

DS-KIT

Linear Single Delta Radio Kit ** Discontinued

Kit includes one DT transmitter and one DR receiver
Same as: DNP00011
Operates on 24 VAC power
One channel
Codes: 1024 (set by dip switches)
RF frequency: 310 MHz

.......more details

Installation Manual

MX00149

Micanan Complete Clutch Shaft Assembly for PRO-H

M18

LiftMaster Remote Control Tester ** NLA

85LMC

LiftMaster Plug-In Power Supply

Plug-in jack for easy installation on Liftmaster receivers
Power input level: 105-135AC 24AC output

10-10355

LiftMaster Solenoid Link

C-200-INSTALLED

Cones 2" Factory Installed (Pair)

For do-it-yourself installation use part no. SF200

.234_2"-LH

Torsion Spring .234 x 2" x 12ft LH Blue/White

Wire size: .234
Inside diameter: 2"
Length: 12 ft

.192_2"-LH

Torsion Spring .192 x 2" x 12ft LH Silver

Wire size: .192
Inside diameter: 2"
Length: 12 ft

41A5668

LiftMaster Gear & Sprocket Assembly for ATS211X

For models: ATS211X ATS2113X
For older model ATS211 use part number 41C4470

Installation Manual Manuel d'Installation

23-2017

LiftMaster Limit Switch SPDT

19-50HL

Half (Offset) Link #50

Half link for #50 chain
ANSI Standard Carbon Steel

41A5483-1C

LiftMaster Circuit Board Assembly *** Discontinued

Assembly includes: Circuit board and end panel
For chain drive units with one light
Fits models 2245 & 2255
Last letter of the part # indicates revision date the most recent product will be sent out
Also known as 41A5483-1 41A5483-1B

CP-SW-TD6A

Lynx Switch Light Delay

For the old Lynx 455 operators

50307

Doorlec Cam Shaft Sub-Assembly EHJ ETH ETBH LJH

For models; EHJ ETBH and ETH
Assembly includes: Cam shaft (26140) Oilite (11801) x 2 Sprocket 41B12-5/8" (31118) Flange Bearing (28002) x 2 and nuts.

VBELT_4L360

Manaras VBelt 4L 36" - repl. by A34

Used on MJ / MJH models
New belt type A replaces old 4L360. Part number VBELTA34

RADIO-15

Manaras MRX-1000 1-Channel 24V Receiver with Commercial Antenna 313 MHz ** To extent of inventory

Controls one operator with MT series transmitters.
Operates on 24VAC.
A LED indicates that the unit has been activated.
Can be installed directly onto the control box of a Manaras operator.
Includes a commercial receiver antenna for increased range.
Will be replaced by RADIO-RE901A

.......more details

Installation Instructions

2235.296

Whiting Coldsaver Bottom Panel 14-1/2" x xxx" with lock seal and retainer (Max 96")

Fits Coldsaver Roll-Up Doors
1-1/8" thick max 96" wide
Includes Lock and keeper

1336.3

Whiting CurbSide Top Panel Closure Bracket for 8" radius track

5600.3

Whiting Truck Door Stainless Steel Bottom Roller Bracket Assy Complete

4010-6FT

Aluminum Retainer only for Light Brush 6' Long 180 degree

For angle application (180 degree)
For use with Light Brush or Vinyl Insert

1008-1-3/8"

Bottom Nail-On for Wood Door Light Duty per foot

For 1-3/8" doors.
Color: Black

1006-1-1/2-16'

Rigid Vinyl Bottom Retainer U-Shaped 16' Long

Black with flexible fin to touch door face.
For door thickness 1-1/2"

1104-18FT-DK-BN

Residential Side & Top PVC Weather-Strip with cap 18' Long - Commercial Brown (DN)

Commercial brown rigid vinyl retainer with commercial brown flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Full case quantity only (12).

1104-8FT-DK-BRN

Residential Side & Top PVC Weather-Strip with cap 8' Long - Commercial Brown (DN)

Commercial brown rigid vinyl retainer with commercial brown flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

1104-16FT-WHITE

Residential Side & Top PVC Weather-Strip with cap 16' Long - White (W)

White rigid retainer with white flexible vinyl.
Dual fin vinyl.
Comes with cap to hide screws.

7001-8-WHITE

Commercial Side & Top Weather-Strip 8' Long - White (W)

White galvanized steel with white dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

1001-24-BLACK

Commercial Side & Top Weather-Strip 24' Long - Black

Aluminum retainer with black dual-fin vinyl

25-42-220

Extension Spring 7' Door - 220 lbs Green w/ clip

Double - Loop
25" long 42" stretch 220 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

95-00114

Truck Door Rivet 1" Stainless Steel

Stainless steel construction
Round head design
Cross Reference: T #89217-0032

27-20127

Truck Door Spring Spacer 35" long for Whiting Roll-Up Doors

Extruded PVC construction with zinc plated thrust washer.
Cross Reference: 2471

DM18-125

Cable Drum Vertical Lift 18' 1100-18 (1-1/4") Pair

18' Vertical Lift aluminum die cast alloy cable drums for 1-1/4" shaft.
3/8"-16 x2" hardened cup point set screws installed with red heads.
Color coded: Red=LH and Black=RH. Pair includes (1) LH and (1) RH.
Max. Door Height: 18'-1".
Rated Lift per Drum: 660 lbs.
Max. Cable Diameter: 3/16".

.......more details

SF600U

Spring Fitting 6" Pair Universal Thread Stationary + Winding for 1" Shaft

Universal thread and is available for 1" or 1.25" Bore - must specify when ordering.
Pair includes: (1) winding & (1) stationary.
Not single thread.
Winding bar hole 5/8"

EP2984

Exhaust Port 4" with latch long barrel ** Discontinued**

4" inside diameter 2" sleeve with latch.
Includes fasteners & gaskets.
Polished aluminum finish.

CB3160500

Cable 3/16" 7x19 500' Galvanized

Galvanized cable 3/16" 7x19 500ft spool.
Cable break strength: 4200 lbs

Comparison charts

R5211

Cast Iron Pulley 5" with stud

5" Cast Iron Pulley with double stud
cast iron pulley mounted on two pressed sealed bearings
Maximum cable diameter: 1/4"

BK021/PR

Commercial 3" Safety Bottom Bracket ** Indef Delivery

Maximum cable diameter: 1/4"
Maximum door weight: 1650 lbs Zinc
Plated Steel
Sold as a pair

HD3076

Lift Handle Roll Grip Round Zinc Plated 5-1/2"-5-3/4"

Measures 7" from end to end
Measures 5.5" from eyelet to eyelet

1003-1-3/8-10'

Aluminum Bottom Retainer L-Shaped

For 1-3/8" thick doors.

MD-00247

Double Sprocket 41B14 / 41A32 with 3/4" Bushing

Double sprocket for clutch shaft on PRO-H/HB
includes 3/4" ID brass bushing

PRO-LJ-5011-U-LH

Micanan 1/2HP 115V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

MOUNTSHAFT014

Manaras Clutch Shaft Kit for Opera-H (OPH)

Input / clutch shaft kit for Manaras Opera-H

Drawing

RELAY043

Manaras Relay 4-Pole 24VAC

Used on Manaras MLJ MLH MLT Models

.205-3.5-10-RHW

Mini Storage Spring .205 x 3.5" x 10" long Right Hand

27-20400

Truck Door Bracket for Torsion Assembly RoadSide (LH) for Todco Roll-Up Doors

Steel construction
Zinc plated finish
Cross Reference: T #51036-2 W #4028 360000

232168

Capacitor 3/4 HP 220V 65 MFD

For LCO75 only

ME113-L

Miller Edge Black Left Hand Outlet 2-Wire 1-1/2" wide x 1-1/2" high Sold by the Foot

Slide in edge designed for commercial sectional doors
Retrofits easily to 1-1/4" to 1-1/2" sectional doors
Touch sensitive signaling allows for immedita stopping or reversing of motion
For a sectional door: measure the daylight opening of the door or measure the panel width of the door
This gives you the "active length" of the edge - the length to order.
Lead wire: 22 gauge universal

.......more details

Installation Manual Worksheet Sell Sheet

LVB636-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

ALUM-571

Aluminum 24" x 100' Spool Brownstone / Beige Antique # 571

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 571
Reverse side is #431 Bright White

Colour chart

10TD433HH2

BEA 2-Button Digital Transmitter 433 MHz

Transmitter offering means of activation of automatic doors with extended hold feature.
Delay and no-delay learn modes for either instant of delayed activation for sequencing doors.
Operating temperature: -10 to 55C
Controls one 10RD433 receiver.

K07-2706

LiftMaster Arm Hub

Also known as: 072706 07-2706 07-2706-1 G072706
For use with various LiftMaster® SW420 Series Swing Gate Operators

1-1093

RW Track Bracket #333

22 x 333

1-0243

RW Stay Roller 153 Galvanized

For use on #31 square track

RB-G-K10C

Miller Edge RBand Monitored Wireless Gate Edge System

RBand Gate Edge Transmitter/Receiver System
The system is intended to provide a wireless connection between a monitored sensing edge and a motorized operator that controls the associated gate
The RBand Receiver is compatible with up to 3 RBand Transmitters on 2 channels; 6 total transmitters.
RBand meets the 2016 UL 325 requirements for monitored devices and has been certified as a UL 325 Recognized Component.
It is designed for use with operators that comply with 2016 UL 325 using a Miller Edge 10K Sensing Edge.