Devanco Canada - Get The Right Garage Door Opener‎ and Parts

J751L5

LiftMaster Industrial-Duty Jackshaft 3/4 HP 115/230V 1Ph L5

Doors used with this operator should be balanced with the ability to be manually lifted by hand in an emergency or power outage.
The operators are typically mounted to the wall when used with smaller sectional overhead doors with a vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
J operators are attached to the door jackshaft to indirectly drive the door
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Security+ 2.0® safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you

Installation manual Manuel d'installation Sell sheet Brochure

15-19478

LiftMaster Sprocket Assembly

For model H (2005-present)
48B32T with hub

JDMG-LG-2030

GDI Jackshaft DC 115V

Brushless DC high reliability high efficiency and low maintenance motor
No maintenance GearMotor sealed stainless steel bearings no limits switches no belts or no hydraulic cylinders to maintain
Soft start soft stop

Sell sheet Technical document

.262-258-R

Cut-to-Length Torsion Spring .262 x 2-5/8" Right Hand Wound Red/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

MK-00157

Micanan Intrinsically Safe Modification (Safepack)

Modification available for add-on to certain models only

1007-1-5/8-8

Aluminum Bottom Retainer Flat Fits Doors 1-5/8 to 1-3/4" Thick

For door thickness of 1-5/8" to 1-3/4"

1104-ASFT-9FT

Elton Aluminum Stiffener for 1104 9ft

Prevents the 1104 from buckling in the hot sun

1458W

Fasteners Self-Tapping Stainless Steel Hinge Screw with Washer 1/4" x 5/8"

400 Series Stainless Steel
Self Threading
Washer Head with Rubber Seal
Use with Stainless Steel Garage Door Hinges

41A5507-B

LiftMaster Receiver Logic Board for 2500 (390 Mhz) ** Discontinued

With end-panel
Also known as 41A5507 41A5507B

27-48-240

Extension Spring 8' Door - 240 lbs Blue

Single - Loop
27" long 48" stretch 240 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

K94-36411

LiftMaster Piezo Alarm

For LA400DC

K1D8052-1CC

LiftMaster Control Board for LA500DC LA400 LA412

014D1270D

41DS002-2

LiftMaster Electronic Circuit Board Screw Drive Models 3840 *Discontinued*

Logic Control Board 315 MHz
Compatible with 3840 Screw Drive Purple Learn Button

JRGX1

Chain Hoist Jack Shaft JRG V2 1" Shaft Torque Force (126689)

Jack Shaft Mounting plastic guide 4.5:1 reduction
Gear drive
Fits 3-3/8" minimum offset
Includes: 26' of galvanized hand chain - doors higher than 15' require additional hand chain
1 chain keeper
2 shaft collars

.......more details

Sell sheet

EAST/STL-E3

Rolling Steel 3" Cast Eastern Steel Endlock

Endlocks are riveted to curtain slats ends of every other slat to prevent slats from shifting laterally and to prevent curtain wear in guides.
Continuous endlocks are both ends of every slat.
Rivets included with endlocks

ST316COP

Copper Stop 3/16" 100 Stops per Pkg *price on request

Stops ONLY
Sleeves sold separately part # SL316COP

.283-2-5/8-LH-C

Torsion Spring .283 x 2-5/8" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .283 ID: 2-5/8" Length: 12 ft

.262-1-3/4-LH-C

Torsion Spring .262 x 1-3/4" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .262 ID: 1-3/4" Length: 12 ft

.262-2-LH-C

Torsion Spring .262 x 2" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .262 ID: 2" Length: 12 ft

.250-2-5/8-LH-C

Torsion Spring .250 x 2-5/8" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .250 ID: 2-5/8" Length: 12 ft

.250-1-3/4-LH-C

Torsion Spring .250 x 1-3/4" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .250 ID: 1-3/4" Length: 12 ft

.243-2-RH-C

Torsion Spring .243 x 2" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .243 ID: 2" Length: 12 ft

.225-2-5/8-LH-C

Torsion Spring .225 x 2-5/8" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .225 ID: 2-5/8" Length: 12 ft

.225-1-3/4-LH-C

Torsion Spring .225 x 1-3/4" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .225 ID: 1-3/4" Length: 12 ft

.225-1-3/4-RH-C

Torsion Spring .225 x 1-3/4" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .225 ID: 1-3/4" Length: 12 ft

.207-2-5/8-LH-C

Torsion Spring .207 x 2-5/8" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .207 ID: 2-5/8" Length: 12 ft

.207-2-LH-C

Torsion Spring .207 x 2" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .207 ID: 2" Length: 12 ft

BOARD066R

Manaras Replacement Power Board ***No Longer Available

Used on all Manaras circuit board type operators

Installation Manual Manuel d'installation Replacement Chart Guide de remplacement

OPH-6113-CONT-R

Manaras Opera-H 3/4HP 120V 1Ph with Mechanical Contactor Right Hand

A heavy-duty industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a self-engaging chain hoist for manual operation
Clearence: side room required 15"

Installation Manual Sell Sheet

MB-02001

Micanan Electric Motor Only 3/4HP 110/220V 1PH

Base Mount motor O.D.P. FR56
Used on Micanan's T TB APT J EJ H EHJ HHD & SD

MR00007

Micanan Brake Disconnect Cable 1/16" x 12"L c/w Cable Stop

2 Required per operator

MGR20-Y-2U-04

Miller Edge Sensing Edge Round Yellow 2-Wire Universal Outlet 4ft Long

Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates.
3-sided activation allows for immediate stopping or reversing of motion
Contours to round or square posts.
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 6-8 PSI

.......more details

Installation Manual Sell Sheet

OPH-6114-ECB

Manaras Opera-H 1 HP 120V 1Ph with Electronic Circuit Board

A heavy-duty industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a self-engaging chain hoist for manual operation
Clearence: side room required 15"

Installation Manual Sell Sheet

K76-36398

LiftMaster Electric Motor 1/2HP 24VDC for CSL24V / CSW24V

Replacement motor with improved brush assembly for CSL24V and CSW24V gate operators

GH105-L5

LiftMaster Gearhead with Brake 1 HP 575V 3-Phase Logic 5

GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
GH operators are attached to the door jackshaft to indirectly drive the door.
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.
MyQ Mobile App is a free download with no annual activation fee.

.......more details

Installation Manual Manuel d'Installation Sell sheet Brochure

02-409B

LiftMaster Key Switch with Best Cylinder

Two Position Key Control Station
Outdoor Surface Mt. (NEMA 4/12)
Tamperproof
Die cast metal enclosure with BEST cylinder (construction core included)
OPEN/CLOSE spring return to center (OFF) key removable in center position only. Should only be used on operators wired for constant pressure to open and close (all LiftMaster industrial operators with type D control wiring).
Dimiensions: 3" x 3.2" x 4.2"

.......more details

MOTOR254-WIRED

Manaras Electric Motor 1/2HP 120/240V 1PH Wired (MOD025A04)

Continuous-duty base mount 60Hz
This item is compatible with BRAKE011

315-KEYLESS

Micanan Wireless Keypad for PRO-315 KP303 ***NLA

Guardian model

G90-503000

LiftMaster Non-Resettable Counter 24VAC (50-12862)

Increases one number each time current is applied
Connects to the 24 volts of contactor coil
Simple 2-wire connection
Same as 50-12862

SG10-24RG-LED

TriLite Stop & Go Traffic Signal 24V LED Yellow Housing

Red and Green LED traffic light
Approx. size: 11-1/2" High x 6-1/2" Wide x 4" Deep
24 volt DC input voltage only
Long lasting low power consumption
A simple reliable and cost-effective way to reduce accidents around the loading dock.
Available in two colors: safety yellow or black.

.......more details

Installation Instructions Instructions d'installation Wiring Diagram Schéma de connexion

TAC1

LiftMaster Single Line Telephone Access Control with Radio

The TAC1 can be connected to two devices such as a door or gate using the two independently controlled relays or wirelessly using Security+ technology standard or any combination of the two.
Provides wired communication and secure access control at the gate or door.
Measurements: 6" h x 8.75" w

Installation Manual Programming Instructions

GITR-3

Genie Intellicode 3-Button Remote 37517S 390 MHz *** To extent of Inventory

Replaces Series II GIT-1 GIT-2 & GIT-3
Battery Instructions Visor Clip Included
Note: Only the far right of the three buttons (1 dot button) will operate those older Genie Intellicode units built from 1995 through 1997.
If you have a Genie unit built in 1995 1996 or 1997 this is the only remote that Genie presently makes to operate the Genie garage door openers built during these years.
In this special case the remotes can only be used as 1 button remotes and no other multi-button Genie remote is compatible.

Programming Instructions Instructions de programmation

28-32085

Truck Door 2" Vertical Track with Holes 95.00" Long for Whiting Roll-Up Doors *** To extent of inventory

Galvanized steel 14-gauge construction
Tabbed at both ends for proper alignment at track joints and to allow universal fit for both left hand and right hand frame sides.
Holes drilled to allow for faster plug weld installation to frame
For use with 2" diameter steel or nylon rollers

STATION081

Manaras Push Button Control Station 1-Button Nema 4/12

1-button 1 N/O contact
Plastic

PRO-W_MOD

Micanan Nema 4/12 Modification

This modification provides a TEFC motor N4/12 watertight/oiltight control enclosure waterproof drive and limit chain NEMA4 thru-beam eyes and a watertight/oiltight three-button station.

41B7611

LiftMaster Filter Board w/Screws **to extent of inventory

For model: 8550

.225-258-L

Cut-to-Length Torsion Spring .225 x 2-5/8" Left Hand Wound Orange/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.207-258-R

Cut-to-Length Torsion Spring .207 x 2-5/8" Right Hand Wound Brown

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.225-134-R

Cut-to-Length Torsion Spring .225 x 1-3/4" Right Hand Wound Orange/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

.218-134-L

Cut-to-Length Torsion Spring .218 x 1-3/4" Left Hand Wound Yellow/Orange

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

.207-134-R

Cut-to-Length Torsion Spring .207 x 1-3/4" Right Hand Wound Brown

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

CPS-N4

LiftMaster Nema 4 Commercial Protector System Photo-Eyes with Interface box

Commercial Through Beam Photo Eyes includes:
50-15514 I/R Emmitter
50-15515 I/R Detector
77-16011 Hardware Kit N4-CPS
001C4629 CPI Housing Assembly
Receiving Eye - A: 50-50997 Sending Eye - A: 50-50998

.......more details

Installation Manual Manuel d'installation

PHOTO-061

Manaras Monitored Photoelectric Cells N4X (Fraba)

Monitored NEMA 4X enclosure through-beam type photocell
4-Wire
Suited for industrial environments
Range: 45 ft
Supplied with 3ft of wire

Installation Manual

ER100

Carlo Gavazzi Reflector 4" (100mm) Square

High quality reflector for retro-reflective photoelectric switches
Dimensions: 100 mm x 100 mm 9.2 mm thick

ME123-YELLOW-RH

Miller Edge Yellow Right Hand Outlet 2-Wire 2" wide x 1-1/2" high Sold by the Foot

Electromechanical slide in edge for sectional doors and sliding gates.
Touch sensitive singaling allows for immediate stopping and reversing of motion
Temperature range: -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Installation Manual Worksheet Sell Sheet

377LMC

LiftMaster Wireless Keyless Entry 315 MHz ***Replaced by 878MAX

Compatible with Liftmaster Sec+ garage door openers commercial door operators gate operators and radio control receivers
Mounts easily to the door jamb with two screws
Compatible with openers built 2005+
Replaces 376LMC and same as Chamberlain 956D same as 377LM
Includes 9V battery

Programming Instructions Instructions de programmation

886LM

LiftMaster Motion-Detecting Control Panel Sec+ 2.0 *** To extent of inventory

Push button for garage door operation
Motion-detector automatically turns on the light when movement is detected
150 degree sensing angle for motion sensor
Program remote controls directly from the control panel
Light run-time is 4 1/2 minutes with adjustable light timer option
On/Off switch for deactivation of motion-detecting function

.......more details

Installation Manual

.243_3-3/4"-LH

Torsion Spring .243 x 3-3/4" x 12ft LH White/Yellow

Wire size: .243
Inside diameter: 3-3/4"
Length: 12 ft

.273_2-5/8"-LH

Torsion Spring .273 x 2-5/8" x 12ft LH Orange/Red

Wire size: .273
Inside diameter: 2-5/8"
Length: 12 ft

.283_2-5/8"-LH

Torsion Spring .283 x 2-5/8" x 12ft LH White

Wire size: .283
Inside diameter: 2-5/8"
Length: 12 ft

.243_2-5/8"-LH

Torsion Spring .243 x 2-5/8" x 12ft LH White/Yellow

Wire size: .243
Inside diameter: 2-5/8"
Length: 12 ft

829LM

LiftMaster Garage and Gate Monitor Sec+ 2.0 **to extent of inventory

This innovative monitor lets you check and close the garage door or gate from any room in the house.
Green and Red LED lights indicate whether the garage door or gate is open or closed.
Volume controlled audible alert lets you know when the garage door or gate is being opened.
Able to monitor and close up to four garage doors or gates.
Compatible only with new Sec+ 2.0 MyQ compatible garage door and gate operators.

Programming Instructions Instructions de programmation

R-831-J

FL-Allstar 1-Door O/C/S Receiver in Oil Tight Case (JIC) 107478-311 MHz **NLA

This receiver is included in a JIC box.
Like the model R-831-P it has three isolated contacts to open close and stop the doors and a possibility of 6 561 operational codes to enhance the security level. If your operator can be controlled by three button station then our R-831-J receiver and commercial remote controls will work with your operator.
Manufacturer's model number: 190-107478
Dimensions: 9 1/4" x 6 7/8" x 1 1/4".

Programming Instructions - Dip Switch Version Programming Instructions - Learn Button Version

CP-SW-TD6A

Lynx Switch Light Delay

For the old Lynx 455 operators

.273_3-3/4"-RH

Torsion Spring .273 x 3-3/4" x 12ft RH Orange/Red

Wire size: .273
Inside diameter: 3-3/4"
Length: 12 ft

.243_3-3/4"-RH

Torsion Spring .243 x 3-3/4" x 12ft RH White/Yellow

Wire size: .243
Inside diameter: 3-3/4"
Length: 12 ft

.273_2-5/8"-RH

Torsion Spring .273 x 2-5/8" x 12ft RH Orange/Red

Wire size: .273
Inside diameter: 2-5/8"
Length: 12 ft

.243_2-5/8"-RH

Torsion Spring .243 x 2-5/8" x 12ft RH White/Yellow

Wire size: .243
Inside diameter: 2-5/8"
Length: 12 ft

.218_2-5/8"-RH

Torsion Spring .218 x 2-5/8" x 12ft RH Yellow/Orange

Wire size: .218
Inside diameter: 2-5/8"
Length: 12 ft

.250_2"-RH

Torsion Spring .250 x 2" x 12ft RH Green

Wire size: .250
Inside diameter: 2"
Length: 12 ft

.234_2"-RH

Torsion Spring .234 x 2" x 12ft RH Blue/White

Wire size: .234
Inside diameter: 2"
Length: 12 ft

.273_1-3/4"-RH

Torsion Spring .273 x 1-3/4" x 12ft RH Orange/Red

Wire size: .273
Inside diameter: 1-3/4"
Length: 12 ft

MI00006

Micanan VBelt 5L 32.5" 5L325

H14GHALF

Half Hinge #1 x 14 gauge

Bright zinc plated 14-gauge steel hinge
For use with 7/16" diameter stem rollers
Full body hinge 1-5/8" wide with slotted holes

LIMIT021

Manaras Single Limit Switch with Flat Lever

Single limit switch (SPDT) used to stop the door at top and bottom or as disconnect switch
Unimax
Snap-action

Limit Switch Chart

RADIO-47

Manaras MCT-1 3-btn O/C/S transmitter 1 door **Replaced by RADIO-EM932

Open/Close/Stop remote for 1 door
Comes with LED battery life indicator
9V battery included
Can be wall or post mounted
Must be used with MCR series receivers

Programming Instructions

7145.96

Whiting Bottom Seal For Coldsaver 96" long

Aluminum retainer sold separately

298601

Linear Wireless Multi-Code Keypad 310 MHz

Compatible with 310 MHz Stanley and Multi-Code receivers
4-digit access code
Backlit keys
Easy access to battery
Power: 9-volt battery
Codes: 1024 (set by dip switches)

.......more details

Installation Manual

111645

Allstar MVP 1-Channel 4-Wire Gate Receiver 318 MHz ***Replaced by P-9931R-4F

One channel
4-wire operator connection
Wire whip antenna with "F" connector
Compatible with Allstar Classic Allister and Pulsar dipswitch transmitters and MVP quik-code transmitters
Power: 24 VAC/VDC
Codes: 19683

.......more details

Programming Instructions

HAE00002

Linear Safety Beam Set *** No Longer Available

Set includes: Sender and Receiver photocells wire and connectors
Safety beams will work with all Linear operators that currently have safety beams installed.