Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MK-00048

Micanan Overload Reset 3-Phase 1.2 - 1.8 Amps

MK-00223

Micanan Transformer 460V-110V-100VA

MK-00099

Micanan Utility Limit Switch (Telemecanique) w/Roller

MV-00012

Micanan 3-btn O/C/S w/Key Lock-Out Metal Housing Nema-4 Pushbutton Control Station

Surface mount
Metal Housing

MV-00002

Micanan 2-btn O/C Nema-1 Pushbutton Control Station Metal

Surface mount

1005-1-3/8-12'

Aluminum Bottom Retainer U-Shaped 12' Long

For door thickness 1-3/8"

SD105L5-RH

LiftMaster Heavy-Duty Slide Door Operator 1 HP 575V 3PH Right Hand (Must include hardware box)

Perfect for split and sliding doors involved with industrial applications.
It is installed above the door and corresponds with the direction the door will be traveling.
Comes equipped with an emergency disconnect and for manual lifting in an emergency and automatic reconnect.
The new logic 5 commercial operators come with MyQ Technology built in. * 828LM required
Built In Security+ 2.0 radio receiver
Solenoid brake included

.......more details

HAML-MOUNTING-BRKT

GDI Side Mounting Bracket N/C When Ordered w/Operator

OSH-6434-ECB-LH

Manaras Opera-SH 1 HP 480V 3 Ph with Electronic Circuit Board Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual

PRO-J-10011-U-LH

Micanan 1HP 115V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Installation Manual (EN) Specification Sheet

.319-514-L

Cut-to-Length Torsion Spring .319 x 5-1/4" Left Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-514-Installed

.295-514-L

Cut-to-Length Torsion Spring .295 x 5-1/4" Left Hand Wound Blue

Priced per inch
For factory installed cones priced seperately - use part no. C-514-INSTALLED

2996.3

Truck Door 2" Steel Roller 5" Long Stem Enclosed Bearing for Whiting Roll-Up Doors

A Whiting original

PRO-J-7581-U-RH

Micanan 3/4HP 208V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5023-U-RH

Micanan 1/2HP 230V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5021-U-RH

Micanan 1/2HP 230V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5081-U-LH

Micanan 1/2HP 208V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-LJ-5021-U-LH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

PRO-GT-15081-U

Micanan 1-1/2HP 208V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-GT-15011-U

Micanan 1-1/2HP 115V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-GT-10081-U

Micanan 1HP 208V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-7581-U

Micanan 3/4HP 208V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-5021-U

Micanan 1/2HP 230V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-APTB-7553-U

Micanan 3/4HP 575V 3P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

PRO-APTB-5011-U

Micanan 1/2HP 115V 1P Apartment Trolley Operator With Brake N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-7523-U

Micanan 3/4HP 230V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-T-5038-U

Micanan 1/2HP 380V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-5083-U

Micanan 1/2HP 208V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

MB-05504

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 56C

Fits GT GH GHC & GSD

PRO-LT-5021-U

Micanan 1/2HP 230V 1P Commercial Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial doors with standard lift tracks that require no more than 15 cycles per hour
Trolley track for door up to 12ft standard upcharge for 14' & 16'
Door speed 9 inches per second
UL325
On-Board receiver holds up to 20 transmitters

60-7242

Econo Caution Sign English 14" x 10"

60-7248-CMH94

Wheel Chock Safety Pkg incl'd: chock with integral handle wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) CMH-94 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
One Piece Solid Rubber
Integral Handle
Long Lasting 80 Durometer rubber
Size: 7-1/4" wide x 9-3/4" long x 7-3/4" high

CP-SH-58-1212

Lynx Clutch Shaft Only for MCJH 5/8" x 12-1/2"

No pulley

LR110LTB3815

Telco Thru Beam Receiver M12

Remote receiver Series 110
M12 x 1 Housing Size
Nickel Plated Brass Housing Material
15 m Cable Cable Connection
IP 67 Sealing Class

SRB-5

Standard Riser Bracket for 6" Above Dock or Less 5"

Standard 5" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

T

Molded Rubber Bumper Black 22" L x 10" W x 12" W 3" Projection Centered Reflector 3-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 3 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

DBE-20

Molded Rubber Bumper Black 20" L x 4 1/2" W 3" Projection 4-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 4 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

MM00447

Micanan Idler Wheel PRO-APTC

LVB1220-11

Laminated Bumper Black 12" Projection Vertical Installation 20" L x 11" W Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB1212-14

Laminated Bumper Standard Black 12" L x 14" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1012-24

Laminated Bumper Standard Black 12" x 24" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1010-14

Laminated Bumper Standard Black 10" x 14" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB912-36

Laminated Bumper Standard Black 12" x 36" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB910-36

Laminated Bumper Standard Black 10" x 36" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB820-11

Laminated Bumper Black 8" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB810-36

Laminated Bumper Standard Black 10" x 36" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB810-14

Laminated Bumper Standard Black 10" x 14" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

Drawing

TB412-36SF

Steel Faced Laminated Bumper Black 12" x 36" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB412-24SF

Steel Faced Laminated Bumper Black 12" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-24SF

Steel Faced Laminated Bumper Black 10" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB410-36SF

Steel Faced Laminated Bumper Black 10" x 36" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB636-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TB612-18SF

Steel Faced Laminated Bumper Black 12" x 18" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB612-14SF

Steel Faced Laminated Bumper Black 12" x 14" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB610-14SF

Steel Faced Laminated Bumper Black 10" x 14" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB610-36SF

Steel Faced Laminated Bumper Black 10" x 36" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

8010

LiftMaster DC Chain / Cable Drive Garage Door Opener ***Discontinued***

Customized DC Motor with soft start/stop action.
Chain/cable square steel rail (SSR) system for efficient operation and standard performance.
Security+2.0 increases remote control range and reduces interference for consistent operation.
PosiLock® electronically protects against forced openings.
The Protector System® invisible light beam auto-reverses the door if there is an obstruction.
Comes with: Door Control Button (883LM) 1-Button Remote Control (891LM)

.......more details

44-60-280

Extension Spring 10' Door - 280 lbs Gold ** By Quote Only

Clipped ends
44" long 60" stretch 280 lb load

PRO-GHC-30053

Micanan 3 HP 575V 3P Gearhead Operator No Controls

Specification sheet

34115

Doorlec Awning Pulley 194 x 1"

Used on model LDJ & LDJ-3

T007

Manaras Trolley Track 7ft for 1/2HP models *Actual length 114"*

For models MLT/OTH/OTBH 1/2hp only with Chain #48 (#410)

BTM-BK-PCG/PR

Powdercoated Commercial 3" LHR Bottom Brackets Grey Sold as a Pair (L & R) *** NLA

EZ123 UPWARDOR
Powdercoated grey
Use with: 3" straight track
Sold as a pair (includes one left and one right).

HINGE-411-PCG

Powdercoated Hinge #4 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #4 - 0.74 lbs
Powdercoated Grey
For use with 7/16" stem rollers

WRW

Erone Wiegand Wireless Receiver 433MHz

433 MHz radio frequency systems offer longer range (up to 250m (820ft) less interference jamming and excellent reliability.
KeeLoq® Rolling Code technology ensure ultra-secure transactions.
Output: Wiegand 26 bit
Power requirements: 12 or 24V (AC or DC)
Dimensions: 105 x 45 x 28mm (4.3 x 1.75 x 1.1in)
Compatible with Centaur and any 26 bit Wiegand-capable systems

.......more details

Wireless System Chart

02-404

LiftMaster Key Switch Assembly On/Off Nema 4/12 **DISCONTINUED

Two Position Key Control Station
Outdoor Surface Mt. (NEMA 4/12)
Non-Tamperproof
OPEN/CLOSE spring return to center (OFF) key removable in center position only.
Should only be used on operators wired for constant pressure to open and close (all LiftMaster industrial operators with type D control wiring).
Die cast metal enclosure

.......more details

RP-TRF-110-2415VA

Lynx Transformer 110/24 15VA *** NLA

For old 455 Automatic Doorman opener

MB-03202

Micanan Electric Motor Only 1 HP 575V 3PH Base Mount O.D.P FR56

Fits T TB APT APTC J EJ H EHJ HHD SD

MG00013

Micanan Ribbed Hex Nut 3/8" - 16 UNC

PRO-GHC operator parts
8 required per operator

MD-00005

Sprocket 410B12 3/8" NO KW 2 SS 1/4"

SL585103U

LiftMaster Industrial Slide Gate Op.1 HP 208/230/460V 3 Phase - Heater NOT Incl.

POWER: 115/208/230 VAC. Single Phase
ACCESSORY POWER: 24VAC 500mA max.
MONITORED SAFETY INPUTS: 3 Main Board 3 Expansion Board.
TEMPERATURE SPECIFICATIONS: Without Heater: -4°F (-20°C) to 140°F (60°C). With optional heater -40°F (-40°C) to 140°F (60°C).
Heater option: HTRNB or NTR460 for 460V operators
UL USAGE CLASSIFICATION I II III and IV.

.......more details

Installation manual Manuel d'installation First step for installation Première étape pour l'installation Sell sheet Brochure Wiring diagram Schéma câblage

7-21-1A

Lynx Barlock Latch

Comes with screws

Assembly Manual

37355

Reversing Contactor 120V Coil

ME00037

Micanan Clutch Shaft Only for PRO-LH

LAGS141W

Fasteners Lag Screw Stainless Steel 1/4" x 1" Hex Washer Head 3/8" Sold Individually

DM120-T/FORCE

Cable Drum High Lift 120" D575-120-1 Pair Torque Force

120" High Lift aluminum die cast alloy cable drums.
3/8"-16 x 2" hardened cup point set screws installed with red heads.
Pair includes: (1) LH and (1) RH. Color coded: Red=LH and Black=RH.
Maximum high lift: 120".
Maximum door height: 144" + High Lift.
Rated lift per drum: 500 lbs.

.......more details

BI-004

Astragal Bottom Cloth Black PVC Sold by the Foot

MP-00002-575V

Micanan Apartment Feature: Timer-to-Close Function and Light Control Modification only

Controlling action of two lights- sockets supplied on cover

OPH-6213-ECB-LH

Manaras Opera-H 3/4HP 240V 1Ph with Electronic Circuit Board Left Hand

A heavy-duty industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a self-engaging chain hoist for manual operation
Clearence: side room required 15"

BL229-EX1929/G45

Automatic Systems Rising Barrier Gate with 14'9" Round Arm Left Hand

22000

Doorlec Enclosure EEMAC 12 and 4 1 Hole 22MM

Works with selector switch #22016 (sold separately)

CB380500

Cable 3/8" 7x19 500' Galvanized

Galvanized Cable 3/8" 7x19 500ft spool.
Cable break strength: 14000 lbs

1KXL-BC

Key Switch N4 Exterior Lockout Control with Best Cylinder Surface Mount

Two position ON-OFF
Dimensions: H=4-3/8" W=4-1/8" D=2-5/8"

PRO-GHB50053-PNL

Micanan 5 HP 575V 3 Ph Gearhead with Brake No Controls

Special Order only
No controls in operator- separate panel is required

MK-00519

Micanan Surface Mount Fused Disconnect Modification

Mounted to control panel cover in lieu of primary fuse block inside panel

26CW94323-CUT

Truck Door Bottom Panel with Seal (13" x Cut-To-Size Painted White for Whiting Dryfreight

These panels are cut to customer's specifications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes only with bottom retainer and seal (installed)

.......more details

1005-1-3/8-10'

Aluminum Bottom Retainer U-Shaped 10' Long

For door thickness 1-3/8"

MB-15202

Micanan Electric Baldor Motor Only 2 HP 575V 3PH C-Flange TEFC 145TC (Severe Duty)

MB-15204

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 145TC

Fits GT GH GHC & GSD

5-30-8A

3" Vertical Track 12-GA 14'-4" (15' door) Sold per Pair

Pierced track

MU33-2WIRE-LH-Y

Miller Edge MU33 2-Wire NM Left Hand Yellow - Sold per Foot

MU style bumpers are designed for use with aircraft hanger doors and large specialty doors.
Must specify the exact length in feet and inches when ordering.
Mounts vertically or horizontally
Sensitivity: nominal 8-13 ibf

Worksheet

41A5483-2C

LiftMaster Circuit Board Assembly *** To extent of inventory

Assembly includes: Circuit board and end panel
For chain drive units with one light
Fits models 2245 & 2255
Last letter of the part # indicates revision date the most recent product will be sent out

OCDFX3

Overhead Door 3-Btn Transmitter 315/390 Mhz

Dual Frequency transmitter that will work on all OHD/Genie brand 315 or 390 rolling code commercial openers including the the RX OHD commercial opener.
Part Number: OCDFX3.S GIDFX3.S