Devanco Canada - Get The Right Garage Door Opener‎ and Parts

SEA868

Erone Tuned Antenna 868MHz

Increase reception and/or range
11.5ft (3.5m) coaxial cable (RG 58) included
L-Shaped bracket for wall-mounting

Wireless System Chart

MK-00666

Micanan RF Junction Connector for Antenna

MK-00017

Micanan Ground Lug

MK-00009

Micanan 9-Pole Control Terminal Strip

MK-00175

Micanan Transformer 200V-110V-100VA

MV-00214

Micanan Tele 8" Wand (For Utility Switch)

MK-00228

Micanan Transformer 230V-24V-50VA

MM-00319

Micanan PRO-GJ L-Bracket Right Angle Front of Coil For Rolling Steel Doors

MK-00235

Micanan Flasher 120V

In closing cycle door will stop for 1.5 seconds and reverse to fully open

RB709U-NB

Linear GTO Garage Door Receiver Adapter Mighty Mule

The RB709 Garage Door Opener Adapter enables the Mighty Mule transmitters to open and close almost any garage door opener
Made to be used with the FM134 (two button) and the RB743 (three button) remote control transmitters or F310 Keypad
Easy to install with almost any garage door opener
One RB709 is needed for each garage door opener that will be controlled by the Mighty Mule transmitters

MV-00272

Micanan Key Switch O/C Single Gang Nema 1 Flush Mount

MV-00015

Micanan Key Switch O/C w/Stop Btn Tamper Proof Nema 4 Surface Mount

MV-00304

Micanan Wireless Key Switch

MV-00008

Micanan 2-btn O/C Nema-4 Pushbutton Control Station

Surface mount
Non-Metallic

MV-00002

Micanan 2-btn O/C Nema-1 Pushbutton Control Station Metal

Surface mount

MV-00004

Micanan 2-btn O/C Nema-1 Pushbutton Control Station

Flush mount

ME110-2W-BLK-R

Miller Edge 2-Wire Black Right Hand Outlet 7/8" wide x 3/4" high Sold by the Foot

Electromechanical slide in edge for counter shutters rolling doors and barrier arm applications.
Touch sensitive signaling that allows for immediate stopping and reversing of motion.
Temperature range -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Worksheet

.375-334-R

Cut-to-Length Torsion Spring .375 x3-3/4" Right Hand Wound Yellow/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

42GRR-AB

Allen Bradley Thru-Beam Photocell RX/TX Long Range 42GRR9001+GRL9040

PRO-J-7511-U-RH

Micanan 3/4HP 115V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5053-U-LH

Micanan 1/2HP 575V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5011-U-RH

Micanan 1/2HP 115V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-LJ-5021-U-RH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Right Hand

On-Board receiver holds up to 20 transmitters

PRO-LJ-5011-U-RH

Micanan 1/2HP 115V 1P Jackshaft N1 Eyes Monitored ECB Right Hand

On-Board receiver holds up to 20 transmitters

PRO-GT-15053-U

Micanan 1-1/2HP 575V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-GT-5023-U

Micanan 1/2HP 230V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-APTB-7523-U

Micanan 3/4HP 230V 3P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

PRO-TB-10023-U

Micanan 1 HP 230V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

K001A6426-2

LiftMaster Control Board RSL12V/RSW12V

MB-05504

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 56C

Fits GT GH GHC & GSD

68-9U

Wheel Chock 68-9U Pyramid Rubber with U Handle

Handles for chain fastening
Long Lasting 80 Durometer rubber
Size: 8" wide x 9" long x 6" high

60-7248-689E

Wheel Chock Safety Pkg incl'd: pryamid chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) 68-9E Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Handles for chain fastening
Long Lasting 80 Durometer rubber
Size: 8" wide x 9" long x 6" high

60-7248-MWC32

Wheel Chock Safety Pkg incl'd: chock w eye hook wall bracket 15' chain 3/8"x1 7/8" anchors (4) 3/16" quick link (2) & English caution sign

System Includes (1) MWC-32 Chock Bracket Tie Back Chain English Caution Sign and (4) Wall Bracket Anchors
Good stability over others in this class
Long Lasting 80 Durometer rubber
Size: 6-1/2" wide x 9-1/2" long x 8-1/2" high

CP-SH-58-1212

Lynx Clutch Shaft Only for MCJH 5/8" x 12-1/2"

No pulley

MX00164

Micanan VFD Transformer Panel Mod. 575V pri / 230V sec (MX00216)

The primary power is connected to the transformer panel and 230V from the transformer panel gets connected to OMC VFD operator

MF00009

Micanan Hex Head Bolt 1/4" - 20 UNC x 2-1/4" Partial Thread

Used on PRO-HHD
1 required per operator

CP-IDLER-ASSY-MR

Lynx Front Idler Assembly Chain TC3

SRB-2

Standard Riser Bracket for 6" Above Dock or Less 2"

Standard 2" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

E/1929/031

Automatic Systems Installation Plate Ass'y BL229

Used on the BL229 gate op.

BB

Molded Rubber Bumper Black 24" L x 10" W 4" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles molded bumpers will not warp rust rot or harden.
Bumper comes with 2 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts
24" L x 10" W 4" Projection

.......more details

MM00447

Micanan Idler Wheel PRO-APTC

MV-00133

Micanan Control Station 3-Btn O/C/S Nema 4 Surface Mount c/w Pilot Light 24V ** DISC..

STRUT-2-1/4-14'-NH

Door Strut 2-1/4" Non Hemmed 14 ft Long ***No Longer Available

Reinforcement bar 2-1/4"
20G

LB1012-14

Laminated Bumper Standard Black 12" x 14" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB412-18SF

Steel Faced Laminated Bumper Black 12" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-14SF

Steel Faced Laminated Bumper Black 10" x 14" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB412-24SF

Steel Faced Laminated Bumper Black 12" x 24" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB612-36SF

Steel Faced Laminated Bumper Black 12" x 36" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB612-14SF

Steel Faced Laminated Bumper Black 12" x 14" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB610-14SF

Steel Faced Laminated Bumper Black 10" x 14" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

2376.182.29.870

Whiting Torsion assembly .182 wire size 29" spring length 87" shaft ** price by quote only

This is a full balancer assembly
Twin springs one road one curb with a shaft through it

T007

Manaras Trolley Track 7ft for 1/2HP models *Actual length 114"*

For models MLT/OTH/OTBH 1/2hp only with Chain #48 (#410)

MK-00694

Micanan 10K OHM Resistor *** DISC Repl by MK00713

K94-36934

LiftMaster Main Wiring Harness L5

K20-1050C-2TLP

LiftMaster Electric Motor 1/2 HP 115/230V 1Ph TEFC Logic

MM-00126

Micanan Wall Mounting Plate (Reducer 80/100)

MH00003

Micanan Oilite Flange Bushing 3/4 ID x 7/8" OD Sold Individually

2 required per machine

MV-00296

Micanan Wireless Push Button Station OCS for Logic 10.0

Used only on Logic 10.0 program 3.2.5

CABLE_364SS-250

Cable 3/64" 7x7 250' Stainless Steel

Not for use in aircraft applications
Type: T304

LIMIT023

Manaras Single Limit Switch with 46 degree Lever

Single limit switch (SPDT) used to stop the door at top and bottom or as disconnect switch
Unimax
Snap-action

CP-HU-LDT-12-115/1

Lynx LDT Medium Duty Trolley Op. 1/2 HP 115V 1P UL325

For standard lift sectional doors
Available in 1/2 HP only
Equipped with instant reversing motor heavy duty ball bearings on all line shafts logic board
Max door height: 14 ft
Solenoid brake optional

MH00006

Micanan Shaft Collar 3/8" I.D

FMB01DW24

Timer Multifunction 11-Pin

Carlo Gavazzi multi-function timer
Time range 0.05 s to 300 h
Knob selection of time range
Knob adjustable time setting
Knob selection of operating mode (6 functions): A - delay on operate B - symmetrical recycler OFF first B2 - symmetrical recycler ON first C - signal ON/OFF delay D - delay on release E - interval
Manual start

.......more details

MP-00002-575V

Micanan Apartment Feature: Timer-to-Close Function and Light Control Modification only

Controlling action of two lights- sockets supplied on cover

33223A

Genie Bushing

Drive shaft bushing on PMX500 Chain Glide

E/BLOP/122

Automatic Systems Red Arm Light - 2 Sets

Increases visibility of the arm on BL229 gate operator

HW0775

Low Headroom Quick Close Device 2" track Sold as a Pair

Includes 1 RH & 1 LH bracket
Heavy Duty for doors up to 16' x 16'

Diagram

.393-514-R

Cut-to-Length Torsion Spring .393 x 5-1/4" Right Hand Wound Orange

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-514-INSTALLED

4X12SC50

Devanco Loop 4' x 12' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation manual Manuel d'installation Loop placement guide Guide de positionnement des boucles

MD-00280

Sprocket 41B32 x 1" 1/4" Keyway 2SS 5/16 Small Hub

2 set screw 5/16

MGH-6214-ECB-LH

Manaras 1 HP 240V 1P Jackshaft with Elect. Circuit Board Left Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

TRACK-GUARD-72

Track Guard 72" Tall Safety Yellow With Base Sold as a Pair ** Special-Order

Provides impact protection to vertical track
45° angle flange adds strength protects from side impact.
7-gauge steel construction powder coated safety yellow for high visibility.
1/4” foot plate drilled with slotted holes for three 1/2” anchors.
Wall flange drilled with slotted holes for four 3/8” anchors
Includes: 60-5094 (right) and 60-5095 (left) sides

.......more details

72"Track Guard Shop Drawing - Left 72"Track Guard Shop Drawing - Right

MGH-6214-ECB-RH

Manaras 1 HP 240V 1P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

5001-12-WHITE

Residential Side & Top Weather-Strip 12' Long - White

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

6X24SC50

Devanco Loop 6' x 24' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation manual Manuel d'installation Loop placement guide Guide de positionnement des boucles

MB-15204

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 145TC

Fits GT GH GHC & GSD

COLLAR002

Manaras Steel Collar 0.375" ID

BUSHING055

Manaras Limit Shaft Bushing

OSH-6114-ECB-LH

Manaras Opera-SH 1HP 120V 1Ph with Electronic Circuit Board Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual

BCH101L5L-BZ

LiftMaster 1 HP 115/230 VAC 1 PH Commercial Hoist Op L5 Carwash and Roller Bearing Mod. LH ***No Longer Available

H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door.
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.
Security+ 2.0™ safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you.

.......more details

PRO-HHD10021U-L

Micanan 1 HP 230V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand

1 HP230V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

Installation Manual (EN)Specification Sheet

OCDFX4

Overhead Door 4-Btn Transmitter 315/390 Mhz

Dual Frequency transmitter that will work on all OHD/Genie brand 315 or 390 rolling code commercial openers including the the RX OHD commercial opener.
Part Number: OCDFX4.S GIDFX4.S

MG020-Y-2E-03

Miller Edge Sensing Edge Yellow 2-Wire End Outlet 3 ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

STRUT-2-1/4-10'-NH

Door Strut 2-1/4" Non Hemmed 10 ft Long *** To extent of inventory

Reinforcement bar 2-1/4"

7001-14-BRONZE

Commercial Side & Top Weather-Strip 14' Long - Bronze (BZ)

Bronze galvanized steel with bronze dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (10)

Q230

LiftMaster Mounting Bracket (2 pcs) MIR-1 (K77-50240)

Steel Bracket Mounting Plates (2) For Elite Miracle and LA500 Operators
Dimensions: 9" x 2-1/4" (1/2" holes) and 6" x 2-1/4" (5/8" hole)

PRO-HBH10053U-R

Micanan 1 HP 575V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand

1 HP575V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

ME113-4WIRE-E

Miller Edge Black End Outlet 4-Wire Monitored 1-1/2" wide x 1-1/2" high Sold by the Foot

Slide in edge designed for commercial sectional doors
Retrofits easily to 1-1/4" to 1-1/2" sectional doors
Touch sensitive signaling allows for immedita stopping or reversing of motion
For a sectional door: measure the daylight opening of the door or measure the panel width of the door
This gives you the "active length" of the edge - the length to order.
Lead wire: 22 gauge universal

.......more details

Worksheet Installation manual Sell sheet

.207-3-7.5-LHW

Mini Storage Spring .207 x 3" x 7.5" long Left Hand

CUSTOM-8X40SC100

Devanco Loop 8 x 40 Saw-Cut 100' Lead-In

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation manual Manuel d'installation Loop placement guide Guide de positionnement des boucles

VBELT_5L370

Manaras VBelt 5L 37" - repl. by B34

5L370

BRAKE012

Manaras Band Brake Retrofit Kit Old GH/MGH

Does not include the solenoid
Replaces BRAKEPART012

30257T

Genie Coupler Screw Drive Units

Used for attaching the screw of Genie screw drive rail to the motor head.
This coupler is made to break away if the door hits a hard obstruction thereby protecting the motor.
If the motor of the screw drive Genie runs but the screw is not turning this coupler needs replaced.
To check and replace that part remove the two screws holding the rail to the main power head
Mounts on rear of opener rail and fits in motor head.

V1102-BLACK

Replacement Vinyl Only for 1102-Black 200ft Roll

Sold in 200 ft rolls only

760130

FAAC Capacitor 115V 25 MFD

APOW1

LiftMaster Transformer For Roboswing & Roboslide Gate Operators *** To extent of Inventory

Elite Robo plug in transformer was 18VAC now replaced by 25V California energy compliant
As of March 2008 transformer has been changed to a 25 VAC self resetting unit that is to be used as direct replacement for the old 18vac units