Devanco Canada - Get The Right Garage Door Opener‎ and Parts

4X10PO50

Devanco Loop 4' x 10' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation Instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

25-01431

Truck Door Stainless Cables 105" 5/16 eye 7x19 Pair for Roll-Up Doors

Works with both Whiting and Todco doors
Cable size: 1/8 "

1104-12FT-WHITE

Residential Side & Top PVC Weather-Strip with cap 12' Long - White (W)

White rigid retainer with white flexible vinyl.
Dual fin vinyl.
Comes with cap to hide screws.

6X12PO50

Devanco Loop 6' x 12' pave-over 50' lead-in

Ideal for use on with gravel driveways or sufaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation Instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

19-5810

LiftMaster Trolley Chain Pack #48 for 10ft Door

Chain pack only

H11G05

Hinge #5 x 11 gauge

11 gauge # 5 hinge - 0.76 lbs
Bright zinc-plated steel construction
For use with 7/16" stem rollers

.363-6-R

Cut-to-Length Torsion Spring .362 x 6" Right Hand Wound Green/White

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

26-945255

Truck Door Intermediate Panel (15.5" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish

MODKIT027B1

Manaras Universal Aux. Output Module B070 Field Install

MODKIT027B1 for field install simply plugs into the control board
Controls traffic lights
Works with BOARD070
Order MOD027B1 when ordered in conjunction with a commercial operator

Wiring instructions

OSH-6812-ECB

Manaras Opera-SH 1/2 HP 208V 1Ph with Electronic Circuit Board

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

1001-16-BLACK

Commercial Side & Top Weather-Strip 16' Long - Black

Aluminum retainer with black dual-fin vinyl

MA116

LiftMaster 17 ft Aluminum Arm Round Yellow/Black Stripes ***NLA Repl. by MA116RDOT

Used on Mega Arm gate operators
Requires counterweight model MA117 - sold separately.
Size: 17 feet long x 3" round
Arm opening area: 14ft (end of cabinet to arm tip)
Replaced by MA116RDOT

Q222

LiftMaster Control Board for MIR-1 (K001A5868) ** NLA

For Miracle-One single operator - one arm
Same as K001A5868

8010-3FT

Bottom Sweep for Entrance Door White ** No Longer Available

Height adjustable
Vinyl: White
Length: 3 ft

SNRKPMKR

LiftMaster MiniKey Keypad White

Also known as: SNRKPVP SNRKPOLP SN1610016-B

4002-12FT

45 Degree Aluminum Retainer for Light Brush 12' Long 45 degree

For angle application (45 degree)
For use with Light Brush or Vinyl Insert.

H12G11-SS

Hinge #11 x 12 gauge Stainless Steel

Manufactured with 12ga. Rust-Resistant Stainless Steel
Universal Design
Fits Most Overhead Sectional Doors
Priced Per Each

MT21-GRAY-RH

Miller Edge 2-Wire Pressure Sensitive Edge Gray Right Hand Outlet Sold per Foot

��Electromechanical medium profile edge for rolling fire door applications. •Touch sensitive signaling allows for immediate reversing or stopping of motion. •The MT21 is completely felixible and will contour to curved surfaces. The MT21 will also act as weatherstrip. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual

COAX-RG6-ASBLY

Coax Cable Assembly Sold per Foot

Assembly includes union

91568

Marantec Sprocket Holder Assembly for Chain Rail *** NLA No Replacement

Compatible with Marantec Chain Standard Rail.
Same as #8030339 (old part number)

271723

Rolling Steel Slide Bolts for Bottom Bar D679

RADIO-22

Manaras MT3-1000 3-btn transmitter 313 MHz

Open/Close remote for 2 doors
Comes with LED battery life indicator
9V battery included
Sunvisor clip included
To extent of inventory replaced by RADIO-EM903

Programming Instructions

111645

Allstar MVP 1-Channel 4-Wire Gate Receiver 318 MHz ***Replaced by P-9931R-4F

One channel
4-wire operator connection
Wire whip antenna with "F" connector
Compatible with Allstar Classic Allister and Pulsar dipswitch transmitters and MVP quik-code transmitters
Power: 24 VAC/VDC
Codes: 19683

.......more details

Programming Instructions

1104-16FT-SAND

Residential Side & Top PVC Weather-Strip with cap 16' Long - Sandstone (D)

Sandstone rigid vinyl retainer with sandstone flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Also known as Taupe

MK-00002

Micanan Timer Module (2 wire)

MA007

LiftMaster Cogged Belt 4L290

Used on Mega Arm gate operators

OPJ-6434-ECB

Manaras Heavy-Duty Jackshaft Operator 1 HP 480V 3 Ph with Elect Circuit Board

An industrial operator designed for use on standard high and vertical lift sectional doors
Can also be used on rolling doors and grills
It incorporates a floor level disconnect mechanism for manual operation
25 cycles per hour 100 cycles per day
Continuous-duty single phase capacitor start or 3 phase motor open drip proof
Mechanical brake

.......more details

Installation Manual Sell Sheet

PREMIUM-R12

Garex Ready to Install Door Special Order

R12 Insulation - Short Panel - Available in white or black steel - A variety of decorative windows can be added - Custom colours can be factory painted - Multiple hardware configurations are available to accomodate site requirements

08-9098

LiftMaster Angle Mount Bracket Mounting Clip

7001-16-WHITE

Commercial Side & Top Weather-Strip 16' Long - White (W)

White galvanized steel with white dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

DECO-FASTNR-HNDL

Decorative Handle (Carriage-Style) Fastener 3/4" Stainless Steel Black 100/pkg

Self drilling metal screw
Stainless Steel all black

E/1929/071

Automatic Systems Round Arm Ass'y 16'-5" (BL229)

Used on the BL229 gate op.

1003-1-5/8-8'

Aluminum Bottom Retainer L-Shaped

For 1-5/8" thick doors.

32-48-60

Extension Spring 8' Door - 60 lbs Brown ** check for availability

Double - Loop
32" long 48" stretch 60 lb load
Springs sold individually

26-942255

Truck Door Bottom Panel with Hardware (15.5" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Primer Finish
Comes with 18" pull strap assembly two bottom roller shaft covers and stud plates standard lift handle two u-bolts flexible PVC bottom seal and aluminum seal retainer.

.......more details

P294-K

Heddolf 4-Wire Single Channel Receiver with F-Connector 318 MHz

Controls one gate or garage door.
318MHz
12 or 24VAC or VDC
9 three position dipswitches (+/0/-) •Switchable relay for pulse to continuous
5 wires: 2 for power 3 for relay contacts
Coax antenna not included. Please see MK-00719 86LM.

.......more details

CLUTCH005

Manaras Friction Clutch 1-3/8" #50 MGH

For MGH 2/3/5HP

LB812-18

Laminated Bumper Standard Black 12" x 18" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

K75-12584

LiftMaster Complete Brake Assembly GH 115V

Complete assembly includes: Brake hub kit Brake release lever Brake disk Spring cup Studs Compression springs Brake solenoid Solenoid cover Spacers Mounting plate Pressure plate Feather key and Fastener.

510.1184.00

Whiting Hold Open Device 1184 Light Duty

Upgrade option when buying a truck door aka Positive Stop Assembly
This is installed onto the panel when the door is opened it is engaged and will keep the door open above the header so there is no hang down of the door.
The door will stay open above the header to eliminated the door being damaged.

DRUM006

Manaras Steel Brake Drum Flat Track - replaces DRUM001

Replaces DRUM001
Brake drum for all operators except Gear Head models prior to 1999.
Use with BRAKEPART018

PRO-TB-7511-E

Micanan 3/4HP 115V 1P Trolley Operator with Brake NM ECB No Eyes

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Non-Monitored board NO photoeyes

PMR10RIT

Carlo Gavazzi Retro-Reflective Sensor with Imperial Connector

PMR series sensors have a sensing range up to 32.81 feet and a fixed sensitivity.
Immune to ambient light Selectable output function.
The plastic housing is IP 67 rated and allows cable or screw terminal connections.
Optional timing features include: Delay on operate delay on release or one shot (triggered on leading or trailing edge).
24-240 VAC or 12~240 VDC
Relay Output

.......more details

K72-19979

LiftMaster Clutch Shaft Kit 2005 +

Assembly includes: Clutch shaft keyed flange bearing dual sprocket 32/14 14-tooth sprocket E-ring compression sprocket chain wheel assembly pulley assembly chain guide assembly shim & thrust washers copper bushing 12-10882 and roll pins

MOD034

Manaras Monitored Photocell Upgrade N1 to N4

Ideal for industrial environments submersible and impact resistant.
Flexible design withstands and realigns after mechanical impact.
Max. range 45ft.
Incl. photoeyes 3ft of conductor wire and mounting hardware.
Applies to all operator models with electronic control "M" types.

27-20112

Truck Door W-Style Spring Assembly Curbside 33" Long

Wire thickness: .182
Spring length: 33 inches long (assembled length)
Inside diameter: 1.188
Includes cable drum and bearing assembly winding cone wound onto spring for stronger desgn and internal spring spacer.

38001404

Tork Winch CW 1800 Curtain Winch Formally TW1200 *** Price by Quote Only

Special Order item

35616R

Genie Dual Frequancy Intellicode Receiver Board

For models: PCG500ML PCG700ML GCG350ML 2020L
Works on 315Mhz and 390Mhz

BK313

Jamb bracket J-13 #13 12 gauge

Sold by the piece
Height 5.25" Length 1.9" Width 2.45"
Bright zinc plated 12 gauge steel
2" long track mounting slot
manufactured to accept ¼” fasteners when attaching to the track and 5/16” to lag to the wall.

4X16PO50

Devanco Loop 4' x 16' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation Instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

D800-120-125

Cable Drum High Lift 800-120 1-1/4" HL Pair

Adjustable cable attachment with screw
Made of aluminum
High Lift capacity: 120" max
Flat capacity: 266" max
Rating: 2200 lb per door max
Keyway: 1 KW of 1/4" width

.......more details

LIMIT015

Manaras Single Limit Switch without Lever

No action limit switch - Cherry
Used on Manaras operators built from 2002 to Feb. 2009
Also used as disconnect switch on Opera models

Limit Switch Chart

26-14325

Truck Door Bottom Panel with Seal (15" x 98") for Todco DryFreight Doors

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish
Comes only with bottom retainer and seal (installed)

K72-12487

LiftMaster Limit Shaft Kit MT BMT MJ mechanical operators

For models MT BMT MJ mechanical operators
Includes limit shaft bearings limit nut sprocket. RPM sensor roll pin & e-ring

PRO-HB-7538U-RH

Micanan 3/4HP 380V 3P Hoist Op. with Brake N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

.312_2-5/8"-RH

Torsion Spring .312 x 2-5/8" x 12ft RH Yellow

Wire size: .312
Inside diameter: 2-5/8"
Length: 12 ft

CAP425

Capacitor 125VAC 425MFD

Motor Start Capacitor 125V 425 MFD

D525-54-HL

Cable Drum High Lift 54" D525-54HL Torque Force Pair

Maximum hi-lift: 54"
Capacity: 500 lbs per drum
Max. cable size: 3/16"
Cable length: Floor to shaft center 66" minus amount of Hi-Lift
Cross reference: DNS 54 OMI 54HL M134-1375

109007

Allstar Slide Switch Only Ivory *** Discontinued

ABC selector switch only

28-2103

Steel Bumper Extension Bracket 4"D x 20" Tall 12"W

4" deep (projection) x 20" tall x 12" wide

OPH-6532-0M00

Manaras Opera-H 1/2HP 600V 3Ph Monitored ECB and N1 Photoeyes Right Hand

A heavy-duty industrial jackshaft operator.
For use on Standard High and Vertical Lift sectional doors.
Can also be used on Rolling doors or Grilles.
Comes with a self-engaging chain hoist for manual operation.
Clearence: side room required 15"

OSHW-6113-1M00

Manaras Opera-SH w/Carwash Mod 3/4HP 120V 1Ph Mon ECB w/N4 Photoeyes Left Hand

A heavy-duty V-belt drive industrial jackshaft operator with Damp Area Modification
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
Solenoid activated Brake

.......more details

1222_DUAL_TROLLEY_20'

LiftMaster Additional Trolley kit for TDC operators for 20' high door includes #41 Chain for 20ft High Door Angle tracks (2x) 20' (Actual length 275") and (1x) shaft

Provides a second drawbar-type operation on wide standard door
Includes 20ft tracks #41 chain hardware & Round Bar 1" x 12'
Works with TDC12 & TDC22 Maxum operators

22DUALTROLLEY16

LiftMaster Dual Trolley Mod for TDC12 TDC22 to 16ft high **includes (TDC41-16) CHAIN PACK (10-5816) 16 FT RAILS x (11-52102) 1" Solid Shaft 12ft (DualAuxTrolley41) Hardware kit

Includes: TDC48-20 CHAIN PACK #41 16 FT RAILS x 1 11-5220 CRSBARROUND1" X 12' x 1 10-5820-P TRACKTROLLEYFOR 16FT DOORPRE-PUNCHED x 2 DUALTROLLEYMOD41 MOD-KITDUAL TROLLEY41 CHN x 1

26004A.S

Genie Bolt Retainer

The bolt retainer is used with the bolt that secures the pulley bracket to the pulley support

MKTG-1031-1

EMX Pastic Screw for IRB-4X2

Replacement screw only

K41-0479-000

LiftMaster Hoist Assembly JH 700 1200 2200

For Maxum JHDC models only
Replaces previous service kit K41-0465-000

PRO-HBH-7581U-L

Micanan 3/4HP 208V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand

3/4 HP208V 1PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

041-0186-000

LiftMaster LED Light Pod Kit for 87504-267 model

Light Pod Replacement Kit. For use with various Chamberlain® Single Lens Belt Drive and Chain Drive Garage Door Openers featuring myQ® technology and no video camera; manufactured after 2021 only.

B/CDJH-34-575-UL

Lynx CDJH Heavy-Duty Jackshaft 3/4 HP 575V w/ ECB and Solenoid Brake Right Hand UL325

3 Button station (NEMA 1) Photoeyes 1-Btn Transmitter
1650 RPM high starting torque motor with overload protection
Inherent Mechanical Brake (I.M.B)
B2 Mode C2 Mode D1 Mode E2 Mode T Mode TS Mode
On board Open Close & Stop for ease of setting limits
Pre-wired to accept sensing devices

.......more details

26130

Doorlec Hoist Shaft Threaded 5/8" x 12" GH/GHX

Works on GH/GHX

RXTA-100

Pulse 2-Channel Receiver

Two-Channel Receiver: Can be programmed to operate one or two doors or for Open/Close or Open/Stop functions.
Universally Adaptable: Works with most available brands/models of transmitters (300-390MHz) including those with rolling code.
9-30Vac/dc input.
FCC approved.

86-925

Gel Connectors Red 19-26 AWG 100/Pkg

Internal moisture-resistant sealant protects wires from corrosion (indoor/outdoor use)
Quick one-step splicing – insert unstripped conductors and crimp
Use with solid copper single-conductor wire 19-26 AWG
Maximum insulated O.D. of .066 in. (1.68 mm)
Permanent connection- once crimped they cannot be reused
Use 12 or 3 ports as needed

.......more details

MYQ-KH1VXXW

LiftMaster Smart Garage Video Keypad Power Adapter Kit

Worry-Free Operation: Plug in using the 25-foot power cord for uninterrupted monitoring.
Never needing to charge or replace batteries means your garage is always accessible and secure.
Easy Installation: Set up in minutes with minimal tools required
Whole-Garage Visibility: Use the adjustable swivel mount to position your Video Keypad for maximum visibility.
See more of what you want and thanks to the discrete and concealable power cord see less of what you don’t.
Extended Reach: Position your Smart Garage Video Keypad wherever you want it and use the 25-foot power cord to connect to any standard outlet.

.......more details

SR-9004-WHITE

Elton Reverse Angle Clip-On Vinyl White 200ft Roll

Side Use – Clips onto Steel Jamb
Also for Residential Use

GALV-331-6-144-L

Torsion Spring .331 x 6" x 12ft LH Galvanized Red/White

Wire size: .331
Inside diameter: 6"
Length: 12 ft
Galvanized

GALV-331-6-R

Cut-to-Length Torsion Spring .331 x 6" Right Hand Wound Galvanized Red/White

Priced per inch - cones and filler sold seperately
For factory installed cones use part no. C-600-INSTALLED
For spring filler use part no. SPRING-FILLER
Galvanized

OTBH-6533-AM05

Manaras Trolley Operator 3/4 HP 600V 3Ph Monitored Board w/N4 Eyes Apt. Model

The Silencio model is a low headroom apartment type operator designed for use on industrial standard lift sectional doors with high daily use requirements
100 cycles per day
It incorporates a drum-shoe type solenoid brake.
Tracks are an extra 36 lbs per track
#41 full roller chain
Includes monitored N4X eyes (PHOTO 061)

.......more details

OTBH-6532-AM05

Manaras Trolley Operator 1/2 HP 600V 3Ph Monitored Board w/N4 Eyes Apt. Model

The Silencio model is a low headroom apartment type operator designed for use on industrial standard lift sectional doors with high daily use requirements
100 cycles per day
It incorporates a drum-shoe type solenoid brake.
Tracks are an extra 36 lbs per track
#41 full roller chain
Includes monitored N4X eyes (PHOTO 061)

.......more details

SM102

Miller Edge Signature Module w/Junction Box for 10K (T2) Sensing Edges

SM-102: Converts a 10K resistive signal
Module: 1.8”H x 1.25”W x 0.8”D (46 x 32 x 20 mm)
Junction box: 1.5”H x 4”W x 2”D (38 x 102 x 51 mm)
Module: ABS plastic with epoxy
Junction box: Galvanized steel
Module: NEMA 4

.......more details

40629A.S

Genie Wire Harness for Door Lock

Includes 1 wiring harness only
Connects to the door lock for Genie Wall Mount garage door openers Overall length 10'
Compatible with models 6070H 6070H-B 6072H-BO 6072H-O 6170H 6170H-B 6172H-BO 6172H-BSV 6172H-BV 6172H-O

PRO-HBH-7553U-R

Micanan 3/4HP 575V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand

3/4 HP575V 3PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

L991S

LiftMaster 1-btn Standard Visor Remote Control Sec+ 3.0

Compatible with LiftMaster® Security+ 3.0™ garage door openers.
Up to 1300 ft. range (conditions permitting).
New and improved seamless set up.
Control one Security+ 3.0 garage door opener.
NEW! Set up and manage your remote in the myQ app for a more personalized experience.
Ultra-secure encryption.

.......more details

Installation Manual Manual d'installation Compatibility Chart 2025 Comparison Chart 2025

1-0418

RW Bow Handle Black Steel

Size: 191
Steel drilled for 1/2" dia bolt
Overall size: 13-1/2" h x 2" w. Handle projects 2-3/4" from doorface
Length of Grip: 8"
Depth: 1-7/8"

2400-201

Linear Key 1/4" x 1/4" x 1-1/2"

2100-917-UPS

Linear Shaft Output 1" HSLG UPS

502290

Trac-Rite Tube Astragal 502290 Sold per Foot

PDC300-34-1-40-20

Pulse300 Direct Drive Opener 3/4 HP 110/240V 1ph 1" Shaft 40:1 20' Cable ** Price by Quote Only

the PULSE 300 Series is recommended for large high-cycle sectional doors rolling steel doors and light springless applications.
It’s an ideal solution for balanced doors up to 1580 lb./500 ft²
The 40:1 ratio is recommended for most balanced commercial applications.
90V horsepower rated DC motor
If power fails the included 9Ah batteries takeover for continued door function
The built-in battery backup system eliminates the need for a chain-hoist but one can still be ordered as an option if desired.

.......more details

D0MKTRP001

DURULITE STD-IND ROLLER KIT

oller kit for Chase Doors Standard DURALITE model doors. Fits 90 X 90 and 180 X 90

RB-G-K10C

Miller Edge RBand Monitored Wireless Gate Edge System

RBand Gate Edge Transmitter/Receiver System
The system is intended to provide a wireless connection between a monitored sensing edge and a motorized operator that controls the associated gate
The RBand Receiver is compatible with up to 3 RBand Transmitters on 2 channels; 6 total transmitters.
RBand meets the 2016 UL 325 requirements for monitored devices and has been certified as a UL 325 Recognized Component.
It is designed for use with operators that comply with 2016 UL 325 using a Miller Edge 10K Sensing Edge.

2200-150

Linear Chain #41 Sold per Foot

GALV-319-6-144-R

Torsion Spring .319 x 6" x 12ft RH Galvanized Blue/Green

Wire size: .319
Inside diameter: 6"
Length: 12 ft

GALV-319-6-144-L

Torsion Spring .319 x 6" x 12ft LH Galvanized Blue/Green

Wire size: .319
Inside diameter: 6"
Length: 12 ft

R5993

Shaft Collar 1" Stainless Steel with 1 Set Screw

Set Screw: 5/16 x 18
1" ID

BGARM12

LiftMaster TECHNA Barrier Gate Arm 12 ft without LED

3” Aluminum arm with integrated LED lights channel designed exclusively TECHNA barrier gate operators
Ships in manageable 6-foot sections for streamlined transport and storage enabling easy on-site assembly
Strong aluminum extrusion with reenforced male/female joining sections and fasteners for a secure fit
The arm features a bottom channel designed to hold BGARMFOAM thereby minimizing the chance of scratching the vehicle. Additionally it is compatible with the S50L a wireless edge safety device.
(Optional) LEDs are easily installed by sliding them into the arm's center channel and securing them with the included press-in clip
IP68 rated waterproof LED lights

.......more details