Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MW-00057

Micanan Splash Proof Cover Light Duty Fully Assembled

Splash proof cover for models: PRO-LJ J LH LHA and GJ
Same as MP-00253

MM-00319

Micanan PRO-GJ L-Bracket Right Angle Front of Coil For Rolling Steel Doors

MV-00304

Micanan Wireless Key Switch

MK-00785

Micanan 3-btn O/C/S Nema-7/9 Pushbutton Control Station

Surface mount
Killark

MV-00006

Micanan 3-btn O/C/S w/Key Lock-Out Nema-1 Pushbutton Control Station

Flush mount

PRO-H-5083U-RH

Micanan 1/2HP 208V 3P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

1005-1-3/8-12'

Aluminum Bottom Retainer U-Shaped 12' Long

For door thickness 1-3/8"

ME110-2W-BLK-R

Miller Edge 2-Wire Black Right Hand Outlet 7/8" wide x 3/4" high Sold by the Foot

Electromechanical slide in edge for counter shutters rolling doors and barrier arm applications.
Touch sensitive signaling that allows for immediate stopping and reversing of motion.
Temperature range -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Worksheet

50740

Doorlec On/Off Switch 575V 3Ph Gate Op

20amp

.363-514-L

Cut-to-Length Torsion Spring .362 x 5-1/4" Left Hand Wound Green/White

Priced per inch - cones sold separately
For factory installed cones use part no. C-514-INSTALLED

.312-258-L

Cut-to-Length Torsion Spring .312 x 2-5/8" Left Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.243-334-R

Cut-to-Length Torsion Spring .243 x 3-3/4" Right Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

2X4PO50

Devanco Loop 2' x 4' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

PRO-J-7583-U-LH

Micanan 3/4HP 208V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5043-U-LH

Micanan 1/2HP 460V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5081-U-LH

Micanan 1/2HP 208V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-LJ-5021-U-RH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Right Hand

On-Board receiver holds up to 20 transmitters

PRO-GT-10053-U

Micanan 1HP 575V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-7521-U

Micanan 3/4HP 230V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

SPRAY-5P6

Aluminum Touch Up Spray Paint 350g Iron Ore / Minerai de Fer #5P6

140g

ALUM-568

Aluminum 24" x 100' Spool Nutmeg / Brun Muscade # 568

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 565
Reverse side is #431 Bright White

Colour chart

.273-258-L

Cut-to-Length Torsion Spring .273 x 2-5/8" Left Hand Wound Orange/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

PRO-APTB-7543-U

Micanan 3/4HP 460V 3P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

PRO-T-7553-U

Micanan 3/4HP 575V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

60-7244

Econo Caution Sign French 14" x 10"

2806.206.325

Whiting .206 x 2-3/16 x 32-1/2" Roadside with Cones

60-7242

Econo Caution Sign English 14" x 10"

60-7248-SC6

Wheel Chock Safety Pkg incl'd: alum. chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) SC-6 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Excellent Surface Grip on Tire and Ground
Lightweight Aluminum
Size: 6" wide x 6-1/2" long x 6" high

68-9U

Wheel Chock 68-9U Pyramid Rubber with U Handle

Handles for chain fastening
Long Lasting 80 Durometer rubber
Size: 8" wide x 9" long x 6" high

60-7248-MWC32

Wheel Chock Safety Pkg incl'd: chock w eye hook wall bracket 15' chain 3/8"x1 7/8" anchors (4) 3/16" quick link (2) & English caution sign

System Includes (1) MWC-32 Chock Bracket Tie Back Chain English Caution Sign and (4) Wall Bracket Anchors
Good stability over others in this class
Long Lasting 80 Durometer rubber
Size: 6-1/2" wide x 9-1/2" long x 8-1/2" high

RELAY043

Manaras Relay 4-Pole 24VAC

Used on Manaras MLJ MLH MLT Models

42GRR-9001

Allen Bradley Series 9000 Photoelectric Sensor Thru-Beam Receiver Unit

nput: 20-40VAC 10-55VDC 4VA

31D380

LiftMaster Sprocket Cover

Sprocket Cover Replacement Kit for use with various LiftMaster® and Chamberlain® Chain Drive Garage Door Openers

D4-120

Extruded Bumper Black 120" L x 4 1/2" W x 3 3/4" H w/Metal Insert

Sold in 10' Lengths and cut to measure
Includes 10' Metal Washer Insert
Comes with 5 Holes for mounting or none - Please Specify When Ordering Bumper

.205-3.5-10-LHW

Mini Storage Spring .205 x 3.5" x 10" long Left Hand

748

Fasteners Self Drill & Tap Tek Screw 1/4-20 x 3/4" (#2PT) 1000/Box

Indented Hex Washer Head
7/16" Head
Max RPM = 2000
#2 point = shorter cutting edge (more thread)

LB1210-36

Laminated Bumper Standard Black 10" x 36" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1210-24

Laminated Bumper Standard Black 10" x 24" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

STATION080

Manaras 3-btn Push-Button Control Station with Key Lock-Out and Pilot Light Nema 4/12

2 N/O contacts and 1 N/C contact for stop.
Surface mount.
Schneider Elect. part no. XALD04H7

LB1010-14

Laminated Bumper Standard Black 10" x 14" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB910-24

Laminated Bumper Standard Black 10" x 24" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB812-36

Laminated Bumper Standard Black 12" x 36" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB812-18

Laminated Bumper Standard Black 12" x 18" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB420-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

Drawing

TB406-24SF

Steel Faced Laminated Bumper Black 6" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB636-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LVB636-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LB612-18

Laminated Bumper Standard Black 12" x 18" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB610-24

Laminated Bumper Standard Black 10" x 24" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB412-36

Laminated Bumper Standard Black 12" x 36" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

ME00010

Micanan Input Shaft PRO-J 3/4" x 11-3/4"

Micanan has permanently changed the length to 11-3/4" from 11-9/16" (2025)

HAE00057

Linear LDCO Motor with Encoder

For LDCO800 operators manufactured before 04/2011 compatible replacement part number HAE00053 for motor with encoder and HAE00054 for encoder board.

MH00004

Micanan Flange Bearing UCFL207-22 1-3/8" Bore

Used on PRO-GHC (BHC-80) for 2 3 5HP
2 required per motor

31343

Doorlec Sprocket 41B23 - 5/8" bore 2-Hole

OTBH-6232-AE06

Manaras Trolley Operator 1/2 HP 208V 3Ph with NM Elect. Circuit Board Apt. Model

The Silencio model is a low headroom apartment type operator designed for use on industrial standard lift sectional doors with high daily use requirements
100 cycles per day
It incorporates a drum-shoe type solenoid brake.
Tracks are an extra 36 lbs per track
#41 full roller chain

MG00041

Micanan Spring Clip 7/8" ID Sold Individually

2 required per machine

108135.0002

Overhead Poly Type V- Belt for Old RG 32" *** by quote only

7-21-1A

Lynx Barlock Latch

Comes with screws

Assembly Manual

37561S.S

Genie Belt and Bullet Assembly 8ft

For use on 8 ft doors
Compatible with the following:
SilentMax 1200 (Model 4042) 1000 (Model 3042) 750 (Model 3055) 550 (Model 2055)
ReliaG 650 (Model 1028) 850 (Model 2028)
IntelliG 1000 (Model 3024)

36190S.S

Genie Control Board 6-Terminal**** NLA

Replaces board # 34514R # 20380R
36190S.S is a six terminal board for use primarily with ML Chain Glide devices.
Replacement board for Chain Drive models: IC250B PMX300 PMX500 ICB and 496.696 CD/B
Replacement board for Chain Glide models: GCG350 GCG350L GCG350M PCG400 PCG450 PCG500ML PCG600 PCG650 H2000C OCG510 OCG550 OCG600ML OCG710 and OCG800ML

OPH-6213-ECB-LH

Manaras Opera-H 3/4HP 240V 1Ph with Electronic Circuit Board Left Hand

A heavy-duty industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a self-engaging chain hoist for manual operation
Clearence: side room required 15"

PRO-HB-7511U-LH

Micanan 3/4HP 115V 1P Hoist Op. with Brake N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

MM00019

Micanan Disconnect Arm PRO-LJ

MGH-6214-CONT-LH

Manaras 1 HP 240V 1P Jackshaft Contactor Left Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

HBSLUD

Stainless Steel Low Headroom Bottom Fixture 2-3" Door 2-3" Track Double End Stile Sold per Pair ** NLA

Manufactured with Heavy Duty 12 ga. Rust-Proof 304 Stainless Steel
Laser Cut for a Clean Finish
For Low-Headroom Track
For 2" or 3" Doors
Fits 2" or 3" Track
Double End Stile

.......more details

MU33-2WIRE-LH-Y

Miller Edge MU33 2-Wire NM Left Hand Yellow - Sold per Foot

MU style bumpers are designed for use with aircraft hanger doors and large specialty doors.
Must specify the exact length in feet and inches when ordering.
Mounts vertically or horizontally
Sensitivity: nominal 8-13 ibf

Worksheet

16-8002

LiftMaster Cogged Vbelt 4L330

Fits BG790 barrier gate opener

BLSI12-PM39X

Pivin Drapeau Spring Assembly for BLS12

OPH-6532-ECB-LH

Manaras Opera-H 1/2HP 600V 3Ph with Electronic Circuit Board Left Hand

A heavy-duty industrial jackshaft operator.
For use on Standard High and Vertical Lift sectional doors.
Can also be used on Rolling doors or Grilles.
Comes with a self-engaging chain hoist for manual operation.
Clearence: side room required 15"

MP-00040

Micanan High Cycle Modification Jackshaft Models PRO-J / H only

For installations with high frequency usage
Double V-belt cast iron flanged precision bearings on all shafts and delay on reverse circuit
Supplied with #50 chain

MG020-Y-2E-03

Miller Edge Sensing Edge Yellow 2-Wire End Outlet 3 ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

PROBE-150

EMX CARSENSE-101 Direct Burial Probe with 150' Lead Wire

Wand only
Requires CS101 (Carsense-101)

MD-00563

Micanan Roller Chain #40 Stainless Steel 10' Pack

CP-BRAKE-DRUM

Lynx Brake drum

.207-3-7.5-RHW

Mini Storage Spring .207 x 3" x 7.5" long Right Hand

.207-3-7.5-LHW

Mini Storage Spring .207 x 3" x 7.5" long Left Hand

MU22-2WIRE-U-GRY

Miller Edge MU22 2-Wire Universal Gray - Sold per Foot

��Electromechanical edge for sectional doors and aircraft hangars. •The MU22 is a custom edge manufactured to exact specifications. •The MU22 is completely flexible and will contour to curved surfaces. It's profile can also be square rectangular or angled. •Touch sensitive signaling allows immediate reversal or stopping of motion. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •Vertical or horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

SPR50B12X1

Sprocket 50B12 for a 1" Shaft 1/4" keyway

ame as MD-00012

VBELT_5L370

Manaras VBelt 5L 37" - repl. by B34

5L370

5001-10-DK-BROWN

Residential Side & Top Weather-Strip 10' Long Commercial Brown

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

MGJ-5011U-LH

LiftMaster Medium-Duty Logic Gear-Reduced Op. 1/2 HP 115V 1Ph Left Hand

MGJ is designed for use on rolling grilles and shutters.
Maximum recommended duty cycle: 12 cycles per hour.
Heavy-duty wormgear-in-oil-bath speed reducer
3-button station for open/close/stop functionality
315 MHz radio receiver is integral to the Medium-Duty Logic board
UL325-2010 Monitored Entrapment Capability (provides primary monitored entrapment protection through monitored photo sensors: either CPS-U or CPS-UN4 or a 4-wire monitored edge using the CPS-EI interface)

.......more details

Installation manual Sell sheet

28301

Insert Bearing Pillow Block Hy-Speed 1"

ASPP-205

PPLK1PH-10

LiftMaster Passport Lite 1-Button Mini Proximity Remote with Sec+ 2.0 Technology 10/PKG

Passport Lite Remote Controls provide cost-effective single button access solutions for gate access only or high-capacity commercial properties applications such as employee parking lots and tenant garages.
These remote controls are specifically designed for gate access control and are not compatible with LiftMaster Garage Door Openers.
2x the range of standard remote controls
Narrow-band transmission on 3 simultaneous frequencies (310 MHz 315 MHz 390 MHz)
Compatible with LiftMaster® commercial receivers (850LM 860LM PPWR STAR1000) and Security+ 2.0™ Gate Operators
Keychain remote control sold in a 10 pack

.......more details

Programming instructions Instructions de programmation Sell sheet Brochure

26CW945255-CUT

Truck Door Intermediate Panel (15.5" x Cut-to-Size ) Painted White for Whiting Dryfreight

These panels are cut to customer's exact measurements.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white

CPS-UN4G

LiftMaster Commercial Protector System Thru-Beam Eyes NEMA4 Black

Waterproof photoeyes.
Monitored Thru Beam Photocell
For direct connect on HCT

MM00159

Micanan Solenoid Lever HR Right

1116633121.S

Overhead 1-btn Transmitter 312 MHz ** No Longer Available

Replaces the 1091303121.S
1 channel transmitter opens and closes 1 door
Codes using 9 dip switches with 3 positions
Battery (ALK12V) and visor clip included
Compatible with all Overhead Door 312 MHz frequency garage door openers that were manufactured before 1996.

DT3+1

Linear 3+1 Channel Transmitter 310 MHz

Activates one GRD gate receiver and up to three separate Delta-3 receivers
Test/operate LED
Visor mounting clip supplied
Power: 9-volt battery
Codes: 256 independent codes for gate + 64 multi-channel codes for doors (set by dip switches)
Frequency: 310 MHz

.......more details

Programming Instructions

2807.192.340

Whiting .192 x 2-3/16 x 34" Curbside with Cones

.262-334-R

Cut-to-Length Torsion Spring .262 x 3-3/4" Right Hand Wound Red/Yellow

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

PRO-4X_MOD

Micanan Nema 4X Modification 1/2HP- 2HP 3-Phase

This modification provides a washdown motor N-4X corrosion proof stainless steel control box enclosure waterproof drive and limit chain and a corrosion proof three-button station.
For options M & U Micanan N-4X photocells are supplied
1/2HP to 2HP Motors

28-30081

Truck Door 1" Horizontal Track 6" Radius for T-Style Std Doors 120" Roadside (LH)

Galvanized steel 14 gauge construction
For use with 1" diameter rollers
6" radius for smooth door operation
Track coupler used for proper alignment at track joints

LEVER051

Manaras Brake Lever MGH C-1 Galvanized

Q239

LiftMaster Limit Switch Wire Harness K70-51094 **DISCONTINUED

Includes harness and 4 limit switches for Miracle One

37222R

Genie Series III Deluxe Wall Console

3 function wall console for use with IntelliG™ and TriloG™ openers.
Same as GBWC-BX
3 function console operates door opener controls lights and security lock out switch.
Not compatible with Series II

.243-258-L

Cut-to-Length Torsion Spring .243 x 2-5/8" Left Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.243-258-R

Cut-to-Length Torsion Spring .243 x 2-5/8" Right Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

MG020-B-2E-05

Miller Edge Sensing Edge Black 2-Wire End Outlet 5ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details