Devanco Canada - Get The Right Garage Door Opener‎ and Parts

DRUM006

Manaras Steel Brake Drum Flat Track - replaces DRUM001

Replaces DRUM001
Brake drum for all operators except Gear Head models prior to 1999.
Use with BRAKEPART018

RADIO-37

Manaras MCR-32 Open/Stop/Close 24V receiver Nema 1 313 MHz ** To extent of Inventory

3-Channel O/C/S receiver controls one operator with MCT series transmitters.
Steel Nema 1 enclosure.
24 VAC input voltage.
2 N/O and one N/C relay
Commercial antenna Included (Radio029).
Replaced by RADIO-RE900A

.......more details

Programming Instructions - ECB Programming Instructions - CONT

2238.096

Whiting Coldsaver Intermediate Panel 14-1/2" x 96"

Fits Coldsaver Roll-Up Doors
1-1/8" thick 96" wide

308302

Linear 2-Channel Multi-Code Key Ring Transmitter 310 MHz

Open/Close remote for 2 doors
Compatible with 310 MHz Stanley and Multi-Code receivers
Easy access to battery and coding switches - 10 dip switches
Power: 12-volt battery
Codes: 1024 codes for each channel (set by dip switches)
RF frequency: 310 MHz

.......more details

Programming Instructions

DR4

Linear 4-Channel Delta3 Receiver 310 MHz *** To Extent of Inventory

Activates four devices or UP DOWN STOP for one commercial device
310 MHz 8 dip switch
Power: 24 VAC/VDC
Dimensions: 4.9" W x 4.2" H x 1.3" D
Same as DNR00023A or DR4V

Programming Instructions

GRD

Linear 1-Channel Delta3 Gate Receiver 310 MHz (DNR00101) ***Discontinued

Auto voltage sensing - no jumpers to set
Single Form ”A” (normally open) relay rated at 30 Volts AC/DC up to 5 Amps
Supplied with whip antenna three feet of coaxial cable and bulkhead connector
Power: 12 - 30 VAC or 10.5 - 30 VDC
Codes: 256 (set by dip switches)
RF frequency: 310 MHz

.......more details

Programming Instructions

HAE00032

Linear 8ft Chain Assembly (HCT8)

HAE00013

Linear Turnbuckle Assembly - Chain (HCT)

HAE00049

Linear Drive Sprocket Holder and Belt Clamp

220205-02

Linear Complete Hardware Kit for LDO LSO LCO

Includes all the hardware needed to install the operator in its entirety.
Includes the rail hardware (door bracket and header bracket) and hardware for installing the safety beams.

232168

Capacitor 3/4 HP 220V 65 MFD

For LCO75 only

7952

Whiting Truck Door Stud Plate Gasket

4007-12FT

Aluminum Retainer only for Light Brush 90 degree**Actual Length 12'2"

For angle application
For use with Light Brush or Vinyl Insert.
die # A-25060

4008-6FT

Aluminum Retainer only for Light Brush 6' Long 180 degree 5/8" Offset

2" with 5/8" Offset
For use with Light Brush or Vinyl Insert

4001-12FT

Aluminum Retainer only for Light Brush 12' Long 45 degree

For angle application (45 degree)
For use with Light Brush or Vinyl Insert.

1009-1-3/4"

Bottom Nail-On for Wood Door Heavy Duty per foot

For 1-3/4" commercial doors.
Color: Black

1019-1-3/8-16'

Rigid Vinyl Bottom Retainer Flat 16' Long

Black - for door thickness of 1-3/8"

1014-1-5/8-16'

Rigid Vinyl Bottom Retainer Notched 16' Long

Black - for door thickness of 1-5/8"

1014-1-5/8-8'

Rigid Vinyl Bottom Retainer Notched 8' Long

Black - for door thickness of 1-5/8"

1015-1-3/4-14'

Rigid Vinyl Bottom Retainer Raised Centre 14' Long

Black - for door thickness of 1-3/4"

1015-1-3/4-8'

Rigid Vinyl Bottom Retainer Raised Centre 8' Long

Black - for door thickness of 1-3/4"

1006-1-3/8-8'

Rigid Vinyl Bottom Retainer U-Shaped 8' Long

Black with flexible fin to touch door face.
For door thickness 1-3/8"

1006-1-1/2-16'

Rigid Vinyl Bottom Retainer U-Shaped 16' Long

Black with flexible fin to touch door face.
For door thickness 1-1/2"

1005-1-3/4-24'

Aluminum Bottom Retainer U-Shaped

For door thickness 1-3/4"

1005-1-3/8-24'

Aluminum Bottom Retainer U-Shaped 24' Long *** 24' is DISC

For door thickness 1-3/8"

1003-1-5/8-16'

Aluminum Bottom Retainer L-Shaped

For 1-5/8" thick doors.

1003-1-5/8-24'

Aluminum Bottom Retainer L-Shaped

For 1-5/8" thick doors.
DIE # ES18010

7001-12-BROWN

Commercial Side & Top Weather-Strip 12' Long - Brown (DN)

Brown galvanized steel with brown dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

7001-8-BROWN

Commercial Side & Top Weather-Strip 8' Long - Brown (DN)

Brown galvanized steel with brown dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

1104-18FT-DK-BN

Residential Side & Top PVC Weather-Strip with cap 18' Long - Commercial Brown (DN)

Commercial brown rigid vinyl retainer with commercial brown flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Full case quantity only (12).

1104-10FT-DK-BR

Residential Side & Top PVC Weather-Strip with cap 10' Long - Commercial Brown (DN)

Commercial brown rigid vinyl retainer with commercial brown flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

1104-14FT-CREAM

Residential Side & Top PVC Weather-Strip with cap 14' Long - Cream (C)

Cream rigid vinyl retainer with cream flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Also known as Almond

1104-9FT-CREAM

Residential Side & Top PVC Weather-Strip with cap 9' Long - Cream (C)

Cream rigid vinyl retainer with cream flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Also known as Almond

1104-18FT-SAND

Residential Side & Top PVC Weather-Strip with cap 18' Long - Sandstone (D)

Sandstone rigid vinyl retainer with sandstone flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Also known as Taupe

1104-9FT-SAND

Residential Side & Top PVC Weather-Strip with cap 9' Long - Sandstone (D)

Sandstone rigid vinyl retainer with sandstone flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Also known as Taupe

7001-12-WHITE

Commercial Side & Top Weather-Strip 12' Long - White (W)

White galvanized steel with white dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

1106-16-BLACK

Commercial Side & Top Weather-Strip 16' Long - Black

Aluminum retainer with black dual fin vinyl

1102-24-BLACK

Commercial Side & Top Weather-Strip 24' Long - Black

Aluminum retainer with black heavy-duty dual fin vinyl.

1106-8-BLACK

Commercial Side & Top Weather-Strip 8' Long - Black

Aluminum retainer with black dual fin vinyl

1102-18-BLACK

Commercial Side & Top Weather-Strip 18' Long - Black

Aluminum retainer with black heavy-duty dual fin vinyl.

1102-12-BLACK

Commercial Side & Top Weather-Strip 12' Long - Black

Aluminum retainer with black heavy-duty dual fin vinyl.

1102-16-BLACK

Commercial Side & Top Weather-Strip 16' Long - Black

Aluminum retainer with black heavy-duty dual fin vinyl.

1102-8-BLACK

Commercial Side & Top Weather-Strip 8' Long - Black

Aluminum retainer with black heavy-duty dual fin vinyl.

1001-24-GREY

Commercial Side & Top Weather-Strip 24' Long - Grey

Aluminum retainer with grey dual-fin vinyl
Sold by full case quantity (10)

1001-24-BLACK

Commercial Side & Top Weather-Strip 24' Long - Black

Aluminum retainer with black dual-fin vinyl

32-48-300

Extension Spring 8' Door - 300 lbs Tan ** Replaced by 27-48-300

Double - Loop
32" long 48" stretch 300 lb load
Springs sold individually

Spec Sheet

32-48-170

Extension Spring 8' Door - 170 lbs Orange ** Replaced by 27-48-170

Double - Loop
32" long 48" stretch 170 lb load
Springs sold individually
Rated for 10000 cycles

Spec Sheet

32-48-60

Extension Spring 8' Door - 60 lbs Brown ** check for availability

Double - Loop
32" long 48" stretch 60 lb load
Springs sold individually

25-42-170

Extension Spring 7' Door - 170 lbs Orange

Double - Loop
25" long 42" stretch 170 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

25-42-70

Extension Spring 7' Door - 70 lbs Orange

Double - Loop
25" long 42" stretch 70 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

94-00105

Truck Door Cotter Pin 3/32" x 1-1/4"

Zinc plated
Cross Reference: T #80401-316 W #10-1009-5 120000

91-00400

Truck Door Step Bolt 1/4"-20 x 1.25" (3/4" head)- Sold Per Piece

Zinc plated finish
Cross Reference: T #80015-1610 120250

28-32072

Truck Door 2" Horizontal Track with 8" Radius 107" CurbSide (RH) for Whiting Roll-Up Doors

SPECS: Length: 107" Fits door sizes: Up to 96" high
Cross Reference: W #11-2
Galvanized steel 14 gauge construction
Tongue and groove for proper alignment at joints
8" radius
For use with 2" diameter steel or nylon rollers

.......more details

27-20306

Truck Door Balancer Bracket Clamp for Whiting Roll-Up Doors

Steel construction
Plain finish
Clamp includes nuts
Cross Reference: W #2526 for both #2376 & #7176 balancers

26-94525

Truck Door Intermediate Panel (15" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish

26-94323

Truck Door Bottom Panel with Seal (13" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood. Primer Finish
Comes only with bottom retainer and seal (installed)

26-94321

Truck Door Bottom Panel with Seal (11" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood. Primer Finish
Comes only with bottom retainer and seal (installed)

26-14521

Truck Door Intermediate Panel (11" x 98") for Todco DryFreight Doors

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish

26-14321

Truck Door Bottom Panel with Seal (11" x 98") for Todco Dryfreight Doors

These panels are cut to an extra wide width to fit wider vehicle applications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment
3/4" thick 7 ply exterior grade medium density plywood Primer finish
Comes only with bottom retainer and seal (installed)

Z9005

Shaft Key Straight 3" X 1/4"

3" Straight Key
Zinc Plated Steel

Z9404

Coupler 1-1/4" Bore Adjustable

Malleable iron for strength
With 2 jam nuts
1-1/4" Bore with 1/4" keyway

DM28VL

Cable Drum Vertical Lift 28' 1350-28 1" Bore Pair

28' Vertical Lift aluminum die cast alloy. •3/8"-16 x2" hardened cup point set screws installed with red heads.
Color coded: Red=LH and Black=RH. Pair includes (1) LH and (1) RH.
Max. Door Height: 28'-1".
Rated Lift per Drum: 1100 lbs.
Max. Cable Diameter: 1/4".
Mounting: 1" (or 1-1/4" must specify when ordering) solid shaft with 1/4" keyway.

.......more details

H11G08

Hinge #8 x 11 gauge

11 gauge #8 hinge - 0.87 lbs
Bright zinc-plated steel construction
For use with 7/16" stem rollers

CBA18A07

Cable Assembly 1/8" 7x7 102" Sold per Pair

Galvanized cable assembly for a 7ft door. (102" = 8'6")
Sold as a pair

RS1039

Roller 3" Steel 9" stem 10 ball - To Extent of Inventory. Replaced by RS1039-C

Steel Roller Wheel diameter: 3"
Working length: 8.5"
Overall length: 9.64"
Box qty: 60 Box weight: 49.6 lbs (3-9-10 Steel)

RN0024

Roller 2" Nylon 4" stem Black

Black Nylon Roller Wheel Diameter: 2"
Working Length: 3.75" Overall Length: 4.75"
Box qty: 250 Box weight: 58.2 lbs (2-4 Black Nylon)
No bearings in head

BK258/PR

End Plate 2-5/8" flanged with bearing 13GA Sold as a Pair (L & R) (EBF 258)

Sold as a pair
Box quantity: 30

25-10276

Truck Door Universal Center Hinge Flush Mount **To extent of inventory

Steel construction Zinc plated finish
Eliminates routing of panels for easier installation
Cross Reference: H-325709

25-01439

Truck Door 1/8" Stainless 5/16" Eye 115" for Roll-Up Doors Sold per Pair

Works with both Whiting and Todco doors
Aluminum eye ends are used on 5/16" eye cables
Cable size: 1/8"

4X6PO50

Devanco Loop 4' x 6' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation Instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

1104-10FT-WHITE

Residential Side & Top PVC Weather-Strip with cap 10' Long - White (W)

White rigid retainer with white flexible vinyl.
Dual fin vinyl.
Comes with cap to hide screws.

OSH-6233-ECB

Manaras Opera-SH 3/4 HP 208V 3 Ph with Electronic Circuit Board

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual Sell Sheet

41A7756

LiftMaster End Panel with Light Socket for 8557

.295-134-R-C

Cut-to-Length Torsion Spring .295 x 1-3/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

OSH-6533-CONT-R

Manaras Opera-SH 3/4 HP 600V 3 Ph with Mechanical Contactor Right Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"

Installation Manual Sell Sheet

1014-1-5/8-24'

Rigid Vinyl Bottom Retainer Notched 24' Long

Black - for door thickness of 1-5/8"

OPH-6113-ECB

Manaras Opera-H 3/4HP 120V 1Ph with Electronic Circuit Board

A heavy-duty industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a self-engaging chain hoist for manual operation
Clearence: side room required 15"

Installation Manual Sell Sheet

T3B-DS

Lynx 3-btn Transmitter Dip Switch 303 MHz

Ultra secure mid-size transmitter with 8 dip-switches for coding
3-buttons provides control for 3 Lynx operators
Compatible with HomeLink in-vehicle remote control
Can be mounted on visor with saddle clip or carried on a keychain
Visor clip and 12V battery included
Will work with Lynx residential operators built from 2000 and up.

.......more details

Compatibility chart

.218-258-L

Cut-to-Length Torsion Spring .218 x 2-5/8" Left Hand Wound Yellow/Orange

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

7543.2

Whiting Bottom Panel with Seal & Channel TempGuard 13-5/16" x 95-1/4" FPW

Replacement for serial # 164352

.306-2-LH-C

Torsion Spring .306 x 2" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .306 ID: 2" Length: 12 ft

7001-8-BRONZE

Commercial Side & Top Weather-Strip 8' Long - Bronze (BZ)

Bronze galvanized steel with bronze dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

CB31605000-KOR

Cable 3/16" 7x19 5000' Galvanized Supreme ** Price on request

Galvanized cable 3/16" 7x19 5000ft spool.
Cable break strength: 4200 lbs
A higher quality cable compared to the Chinese cable
Meets endurance test requirements of over 35000 work cycles
Lubricated for flexability and longer service life

Stainless Steel Cable Specifications

TB412-36SF

Steel Faced Laminated Bumper Black 12" x 36" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

.375-334-L-C

Cut-to-Length Torsion Spring .375 x 3-3/4" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

CARRIAGE006

Manaras Trolley Carriage Aluminum Die Cast

PRO-GT-15023-U

Micanan 1-1/2HP 230V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

MK00643-MOD

Micanan Auxiliary Apt. Circuit Board for Red/Green Light Feature 115V Models Installed on Op.

Available option for electonic circuit board (E) models only

.262_6"-LH

Torsion Spring .262 x 6" x 12ft LH Red/Yellow

Wire size: .262
Inside diameter: 6"
Length: 12 ft
Special Order Minimum lead time 3 weeks

RW-PANEL

Richards Wilcox Replacement Door Panel Special Order

As per customer's requirements

SRB-6

Standard Riser Bracket for 6" Above Dock or Less 6"

Standard 6" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

.243_2-5/8"-LH

Torsion Spring .243 x 2-5/8" x 12ft LH White/Yellow

Wire size: .243
Inside diameter: 2-5/8"
Length: 12 ft

OTBH-6533-1-ECB

Manaras Trolley Operator 3/4 HP 600V 3 Ph with Electronic Circuit Board

Heavy-duty low headroom trolley operator designed for use on industrial standard lift sectional door
25 cycles per hour 80 cycles per day
It incorporates a drum-band type solenoid brake.
Tracks are an extra 36 lbs per track
3/4 HP & 1 HP operators come with #41 full roller chain

Installation Manual Sell Sheet

PRO-T-5081-U

Micanan 1/2HP 208V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters