Devanco Canada - Get The Right Garage Door Opener‎ and Parts

PRO-GH-7523U-R

Micanan 3/4HP 230V 3P Gearhead Operator N1 Eyes Monitored ECB Right Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation
Monitored board
On-Board receiver holds up to 20 transmitters

Installation manual Specification sheet

25-42-190

Extension Spring 7' Door - 190 lbs Light Blue

Single - Loop
25" long 42" stretch 190 lb load
Sold individually
Rated for 10000 cycles

SG-13-NO

Telco Light Curtain with Rectifier Normally Open 72" (13-193-028-D1-E-H58-5) ***No Longer Available

Normally Open
SGR13-193-028-D1-E-HS8-5
SGT13-193-028-D1-E-01-15
1928mm housing 1800mm active height 28 channels NO relay output 15m cable

Specification sheet Wiring diagram

PRO-HB-7525U-LH

Micanan 3/4HP 220V 1P Hoist Op. with Brake N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

PRO-J-10053-U-LH

Micanan 1HP 575V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

SEA868

Erone Tuned Antenna 868MHz

Increase reception and/or range
11.5ft (3.5m) coaxial cable (RG 58) included
L-Shaped bracket for wall-mounting

Wireless System Chart

MK-00679

Micanan Plastic Shoulder for Antenna Connector

MK-00704

Micanan Harness 1-Phase Contactor Board

MK-00346

Micanan Relay 12 VAC 8-Pin Plug-In

MK-01179

Micanan Telemecanique Contactor Kit 24V **use code MK-00493

LC2K1210B7 mini contactor

12119

Doorlec Commercial Aluminum Sliding Carriage with Teflon Insert

Works on all Doorlec trolley operators

.421-6-R

Cut-to-Length Torsion Spring .421 x 6" Right Hand Wound Gold

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

.437-334-R

Cut-to-Length Torsion Spring .437 x 3-3/4" Right Hand Wound Red/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

.283-6-L

Cut-to-Length Torsion Spring .283 x 6" Left Hand Wound White

Priced per inch
For factory installed cones priced seperately - use part no. C-600-INSTALLED

.243-334-L

Cut-to-Length Torsion Spring .243 x 3-3/4" Left Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

.243-334-R

Cut-to-Length Torsion Spring .243 x 3-3/4" Right Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

ALUM-532

Aluminum 24" x 100' Spool Almond / Amande # 532

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 532
Reverse side is #431 Bright White

Colour chart

050DCRJWF

LiftMaster Receiver Logic Board DC. WiFi RJO

Fits: 8500W
Also known as 050DCRJWFMC 50DCRJWFMC

PRO-T-5023-U

Micanan 1/2HP 230V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-5011-U

Micanan 1/2HP 115V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-LTB-5021-U

Micanan 1/2HP 230V 1P Commercial Trolley Operator With Brake N1 Eyes Monitored ECB

Designed for use on commercial doors with standard lift tracks that require no more than 15 cycles per hour
Trolley track for door up to 12ft standard upcharge for 14' & 16'
Door speed 9 inches per second
UL325
On-Board receiver holds up to 20 transmitters

60-7242

Econo Caution Sign English 14" x 10"

88-8XL

Wheel Chock 88-8XL Laminated Rubber Galv. Steel Sides

Made From Used Truck Tire Laminates Compressed and Fastened Under High Pressure
Galvanized Steel Sides
Size: 11-1/4" wide x 14" long x 14" high

60-7248-689E

Wheel Chock Safety Pkg incl'd: pryamid chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) 68-9E Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Handles for chain fastening
Long Lasting 80 Durometer rubber
Size: 8" wide x 9" long x 6" high

60-7248-CMH94

Wheel Chock Safety Pkg incl'd: chock with integral handle wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) CMH-94 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
One Piece Solid Rubber
Integral Handle
Long Lasting 80 Durometer rubber
Size: 7-1/4" wide x 9-3/4" long x 7-3/4" high

2528.093

Whiting Dual-Spring Shaft 93" for Whiting Roll-Up Doors

Constructed of 1" outside diameter heavy-duty steel tubing
Holes pre-drilled
For Whiting balancer #2376

STEELCRAFT_PANEL_SEAL

Steelcraft Intermediate Section Seal V-Bead Sold by the Foot

HCRH1

Hinge Combination Roller Hinge Assembly #1 Galvanized

212SE

Nortek Linear Weatherproof Keypad

120 users
Indoor/outdoor self contained brushed metal housing
Surface mount vandal resistant design
One piece housing suitable for wall post or gooseneck mounting
Durable metal Braille alpha-numeric keys
4 on board programmable timed relays

.......more details

MD-00247

Double Sprocket 41B14 / 41A32 with 3/4" Bushing

Double sprocket for clutch shaft on PRO-H/HB
includes 3/4" ID brass bushing

HRB-12

High Riser Bracket for 7" Above Dock or Higher 12"

High Riser 12" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

SRB-6

Standard Riser Bracket 6" Above Dock

Standard 6" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

DB13-T

Molded Rubber Bumper Black 13" L x 10" W 4" Projection 2-Hole Tapered Sides Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
4-1/2" depth
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles. and will not warp rust rot or harden.

.......more details

LB1010-36

Laminated Bumper Standard Black 10" x 36" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-24SF

Steel Faced Laminated Bumper Black 10" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB410-14SF

Steel Faced Laminated Bumper Black 10" x 14" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

8010-8FT

LiftMaster DC Chain / Cable Drive Garage Door Opener with 8ft SSR Rail (1608LM) ***No Longer Available

Customized DC Motor with soft start/stop action.
Chain/cable square steel rail (SSR) system for efficient operation and standard performance.
Security+2.0 increases remote control range and reduces interference for consistent operation.
PosiLock® electronically protects against forced openings.
The Protector System® invisible light beam auto-reverses the door if there is an obstruction.
Comes with: Door Control Button (883LM) 1-Button Remote Control (891LM)

.......more details

LVB636-11

Laminated Bumper Black 6" Projection Vertical Installation 36" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

MD-00246

Double Sprocket 41B14 / 41A32 with 1" Bushing

Double sprocket for PRO-H/HB

R1

Erone Radium 1-Channel Key Chain Transmitter 433MHz

Designed for the control of automatic closing systems and anti-burglar systems thanks to its very high security coding system (KeeLoq® Hopping code).
The code sent by the transmitter changes at each activation avoiding any scanning and copying risk.
A special algorithm allows to keep synchronized transmitter and receiver.
Range up to 250 m (820 ft)
Ergonomic rugged & durable
Battery: Two 3V lithium battery (CR2016)

.......more details

Wireless System Chart

02-404

LiftMaster Key Switch Assembly On/Off Nema 4/12 **DISCONTINUED

Two Position Key Control Station
Outdoor Surface Mt. (NEMA 4/12)
Non-Tamperproof
OPEN/CLOSE spring return to center (OFF) key removable in center position only.
Should only be used on operators wired for constant pressure to open and close (all LiftMaster industrial operators with type D control wiring).
Die cast metal enclosure

.......more details

LVB620-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

MB-03001

Micanan Electric Motor Only 1 HP 110/220V 1PH Base Mount O.D.P FR56

Base mount motor fits: T TB APT J EJ H EHJ HHD SD

44-60-220

Extension Spring 10' Door - 220 lbs *** By Quote Only

Clipped ends
44" long 60" stretch 220 lb load

VWS-34-SANDSTONE

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Sandstone

Pan head
S point

VWS-34-CREAM

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Cream

Pan head
S point
Also known as Almond

HSLG-221

Linear Commercial Slide Gate Operator 1/2 HP 230V 1 Ph - Heater not Included

Max gate size: 35 ft 1000 lbs
Max duty cycle: Continuous
Integral APeX Controller
Double V-belt to chain reduction
#40 roller chain
Emergency manual disconnect handle

.......more details

Q209

LiftMaster Gear Reducer Pulley K17-50223

DC-1000 1/2" ID

HBSLUD

Stainless Steel Low Headroom Bottom Fixture 2-3" Door 2-3" Track Double End Stile Sold per Pair *** No Longer Available

Manufactured with Heavy Duty 12 ga. Rust-Proof 304 Stainless Steel
Laser Cut for a Clean Finish
For Low-Headroom Track
For 2" or 3" Doors
Fits 2" or 3" Track
Double End Stile

.......more details

19-41119M

LiftMaster Roller Chain #41 with Master Links 59-1/2" Long

Same as: 195105 19-41119MB 19-4119M 1941119M

MB-15202

Micanan Electric Baldor Motor Only 2 HP 575V 3PH C-Flange TEFC 145TC (Severe Duty)

HTLS

Stainless Steel Garage Door Low Headroom Top Bracket 12-Gauge Sold per Piece

Manufactured with Heavy Duty 12ga. Rust-Resistant 304 Stainless Steel
Universal Design.
Fits Most Overhead Sectional Doors
Use for Low-Headroom Doors Only
5-3/4” tall x 2-1/2” wide
Priced Per Each

.......more details

SL-310T

Skylink 1-Btn Visor Mount Transmitter 310 MHz

Easy to carry or clip on sun visor.
Works in conjunction with Skylink Universal Receiver: Model SL-310R.
Operating range of 100 feet and more.
12V alkaline battery included.

BCH101L5R-BZ

LiftMaster 1 HP 115/230 VAC 1 PH Commercial Hoist Op L5 Carwash and Roller Bearing Mod. RH ***No Longer Available

H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door.
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.
Security+ 2.0™ safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you.

.......more details

SPRING002

Manaras Brake Spring

7001-7-BRONZE

Commercial Side & Top Weather-Strip 7' Long - Bronze 7001-BZ (BZ)

Bronze galvanized steel with bronze dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

47DCT

LiftMaster Receiver Logic Board Sec+2.0 Non-MyQ

047DCT is a replacement Security+ 2.0® receiver logic board.
This replacement board does not feature MyQ® technology.
This 315MHz receiver logic board is compatible with various LiftMaster® AC chain drive and belt drive garage door openers; made after 2011.
The unit will feature a yellow learn button.
Same as 47DCCR1 47DCCC1 47DCCL1 047DCT41D8060 1D8060

36773R

Genie Carriage Assembly for 7' Door

Works on Genie IntelliG 1000 & 1200 Garage Door Openers
Includes: carriage emergency release rope and straight arm.
Carriage assembly connects to the shuttle assembly and in turn creates the manual release function for the garage door.

768

Fasteners Lag Screw Hex Regular Profile 5/16" x 3" 100/Bag

7/16" head

GH-3-RH

Doorlec Industrial Jackshaft Door Operator 3 HP 575V 3P TEFC Motor Right Hand

Custom-designed extra heavy-duty industrial-type electric door operator
Worm gear reducer 40:1 ratio
#60 roller chain and sprockets from operator shaft to door shaft.
Door speed: 7 inches per second (approx.)
Adjustable torque limiter
Rotary type limit switches

.......more details

RS3346

Roller 3" Steel 3/4" Shaft 5.8" stem Heavy-Duty 6203 Bearing

Steel Roller Wheel diameter: 3" 5.8" Stem Overall length: 7"
Heavy-duty 3/4" shaft supporting higher weight load applications

AW14K500-12

Miller Edge Air Wave Kit 12ft No Coil Cord

AW14 12ft. of RAH-500 P-50H 218-27-18 P50
Kit Includes: AW14 Air Wave Switch Barbed Coupler (12') RAH-500 1/2" dia. Rubber Hose Wire Nuts End Plugs

029-98205

W-Style Replacement Door White Stainless Steel Package 029-98205

Replacement door size between 98" wide x 105" high
Painted white
Stainless steel package

MA003

LiftMaster Electric Motor Only 1/2 Hp 24VDC BM

Same as: MA003M MA-003 MS003 20-60000-1
Used on Liftmaster Mega Arm gate operators

MK00708

Micanan Varistor Harness 230V with Blue Wires

070032-0000

Overhead Double Drive Pulley

MK-00398

Micanan Capacitor 370V 20 Mf

For limited duty 220V operators

UR2

3M Gel Connectors Red 26-19 AWG 100/Pkg ** To extent of inventory. Repl. by 703-004

Scotchlok Insulation Displacement Connector
RUS Listed Full featured
Max. Diameter Insulation: 0.082" (2.08 mm)
AWG Wire Range: 19-26 AWG Solid Wire
Angle: Straight
Operating Temp. : -40 to 285 degree F. (-40 to 140 degree C.)

.......more details

7812

Whiting Bottom Seal Truss Door White 90" Long

Fits Fed-Ex truck doors

Q013

LiftMaster Idler Pulley K75-50090

Toothless idler gear for use on SL 3000 operators
Includes bolt and sleeve.
Dimensions: 3.5" diameter 1-3/8 wide with 1/4 off set total width 1-5/8 with 1/2" x 2-7/8 bolt idlers sold individually

38079001

Agri Safety Chain GR 70 3/8" x 69"

Min. strength: 20200 lbs
Includes hook joiner link & tag

ULT-MVP-2-D-TEK

EMX Industries Multi-Voltage Loop Detector 2-Channel (ULT-MVP-2U)

Combines small size with 9VDC to 240VAC input range.
Size: 73 x 38 x 78mm
ULTRAMETER™ display indicates the appropriate sensitivity setting the vehicle positioned on the loop
Ten (10) sensitivity adjustments
Four (4) frequency settings
Automatic sensitivity boost (ASB) delay fail-safe/fail-secure and infinite or normal (5 min.) presence

.......more details

MG020-B-2E-06

Miller Edge Sensing Edge Black 2-Wire End Outlet 6ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

TL-36ML-BLUE

LOCTITE Threadlocker Blue 36ML *** Price by Quote

Medium strength
This product cures fully in 24 hours and can be dissembled with hand tools.
This product is an anaerobic adhesive applied by drops to the threads of fasteners. It then cures to a hard thermoset plastic that locks the threads together.
For metal to metal applications only

LDCO800

Linear 800 Newton DC Powered Garage Door Opener Accept Both Belt or Chain Rail *Replaced by LDCO863B*

The energy-efficient DC-powered operator that runs at an AC-equivalent speed.
DC drive motor with soft-start and soft-stop for smooth quiet long-term reliable performance.
Optional Battery Backup available for added peace of mind. Sold separately
Low-power standby mode dramatically reduces energy consumption
Supplies 800 Newtons of lifting force for heavy doors
Compatible with belt-drive or chain-drive T or I beam rails up to 10'

.......more details

Installation manual Sell sheet Remote compatibility chart

41AC150-1M

LiftMaster Electronic Circuit Board Assembly 315 MHz *** No Longer Available Repl by 41AC050-1M

For Sears / Craftsman garage door opener

7-28-1A

Lynx Standard Barlock Kit Bars sold Separately

Bars are sold separately.
Hardware bag for doors 12' and under

Assembly Manual

19863R

Genie Clip and Collar Rail Connectors

For Genie screw drive units having split rails use a collar and spring clip to join the 3-piece screw.
Complete collar and clip set for one 3-piece rail.
Compatible with all screw drive Genie garage door openers
Set of 2 clips and 2 collars
Same as 19806A04 and 19807A04

WHITING-DOOR

Whiting Special Order Plywood Core Dry Freight Door Price by Quote Only

Special order to customer's specs
Premium grade 7 ply 3/4” panels manufactured with a medium density overlay (MDO) laminated to smooth hardwood outer veneers of Transportation Core plywood all designed for optimum strength and appearance.
2" track and rollers for durability.
Tongue and groove joint.
2 cable balancer with independent spring for each cable. Springs treated with rust preventative.
4 rows of hinges.

.......more details

71-90TS

LiftMaster Timer Kit for TS Wiring

Field mod. kit

K72-18615

LiftMaster Drive Shaft Kit

Kit includes: Disconnect Bushing Drive Shaft Pillow Block Bearing Sprocket Disconnect Spring Chain Disconnect Key E-Ring.
Works with SL595 SL590.

CL-74-RH

Wayne Dalton Complete Replacement Barrel Assembly 4.5" Diameter 74" Long

Replacement for serial # 10093517-1 PIPESM

SF375-DUPLEX

Spring Fitting 3-3/4" Stationary Side Only for Duplexing (Short Ear). *** Not Sold As A Pair

To make duplex assemblies you require one pair of SF600 (W & S) and only two SF375-DUPLEX stationary plugs only no need for P375 winding plugs

MD-00006

Sprocket 41B10 x 3/4" NO KW 2SS 1/4

124773

Roller 3" UHMW 7-1/4" Stem Rubber

3" UHMW tire covered with rubber
6202 sealed precision bearing
7-1/4" zinc plated stem
Rating: 200lb load; 10000 cycles of a 12' door
Helps quiet the operation of jackshaft operators

28020004-500

Cable Stainless 1/16" 1x19 500' Inox *** Price on Request

Not for use in aircraft applications
1x19 contruction type 302 / 304

Comparison charts

104083

Marantec Reference Switch for Belt and Chain Rails

This part works with the positioning tab and motor to determine the open & close limits of the actual garage door.

BK020/PR

Commercial 2" Safety Bottom Bracket Sold as a Pair (L & R) *** No Longer Available

Maximum cable diameter: 3/16"
Maximum door weight: 1300 lbs Zinc
Plated Steel
Sold as a pair

MCJH-453-CONT-R

Lynx Heavy-Duty Jackshaft 3/4 Hp 575V 3 Ph Contactor Right Hand ** Replaced by CDJH

Sell Sheet

374UT

LiftMaster Universal 2-btn Mini Transmitter

Dual frequency universal transmitter
Will activate 2 different types of openers (1 on each button)
Compatible with major brands except Marantec & Hormann
This mini remote is NOT compatible with DIP switch remotes or receivers

Programming instructions Sell sheet

22210

Push Button Station 3 Oval Buttons O/C/S Flush Mount ** discontinued. To Extent of Inventory

Three button wall station Open/Close/Stop
NO contacts on the Open and Close buttons
NC contact on the Stop button
Stainless steel surface plate
Flush mount

MHS5011U-RH

LiftMaster 1/2 HP 120 Volt Medium Duty Slow-Speed Jackshaft Operator

Designed for use on rolling sheet doors.
It features an adjustable friction clutch high-starting torque motor with overload protection emergency chain hoist with electric interlock and emergency disconnect chain.
Easy emergency manual operation using a floor level disconnect and an electrically interlocked chain hoist mechanism
Floor level disconnect
24V NEC Class 2
Wiring is factory present to C2 mode

.......more details