Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MG020-Y-2E-04

Miller Edge Sensing Edge Yellow 2-Wire End Outlet 4ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration
Vertical or horizontal mount
ANSI/UL325 recognized component
Mounting channel sold separately
One year warranty

CBB332

Stop & Sleeve 3/32" 100 pair

Includes 100 stops and 100 oval sleeves

LEVER007

Manaras Disconnect Lever for old MJH

Works on model MJH - old units

OSH-6113-ECB-LH

Manaras Opera-SH 3/4HP 120V 1Ph with Electronic Circuit Board Left Hand *** To Extent of Inventory

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual Sell Sheet

SLEDB-110V-AMB

Strobe Light Amber 110V Permanent Mount ** NLA

88 flashes per minute

1005-1-3/4-8'

Aluminum Bottom Retainer U-Shaped

For door thickness 1-3/4"

36664R

Genie Screw Drive Shuttle Assembly

Compatible with the following models: GPower 900 TriloG 1200 TriloG 1500 PowerMax 1200 PowerMax 1500
Works with Screw Drive carriage assembly part # 37845R - sold seperatelty

MI00002

Micanan Pulley 8" OD c/w Bushing 3/4" ID

18004B

Genie Motor Start Capacitor 220VAC 50-60 MFD

Compatible with most 1/3 HP Genie & Overhead operators

41A5615

LiftMaster Chain Spreader

For models 2575 3575 3275 PD752 PD758 and others

9150000628

5/32" Stops ONLY 100/pkg

Stops only - 100 per pack

34538S.S

Genie Magnetic Close Down Limit Switch Assembly 138"

For Chain Glide models

7001-9-W/B

Commercial Side & Top Weather-Strip 9' Long - White and Black (WB)

White galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

747

Fasteners Slotted Track Bolt 1/4-20 x 1" 1000/Box ** Unavailable

Knurled shank
Max torque = 6

804

Fasteners Sleeve Anchor 3/8" x 4" 50/Box

Secure anchoring into concrete brick or block

18007

Doorlec Reducer BHC-63 5/8' or 7/8" Input

Gearbox for GH operator

733

Fasteners Flat Washer 5/16" Zinc 1000/Box

H8064HCLL

Polycarbonate Hinged Enclosure Clear Cover Locking Latch

Dimensions: 8 x 6 x 4
Stainless Steel locking latch
Nema 4X

MH00007

Micanan Shaft Collar 1" I.D

MD00086

Micanan Sprocket 40B18 x 1" 1/4" Keyway

MOTOR274-WIRED

Manaras Electric Motor 3/4HP 575V 3PH Wired

Motor and brake come wired •This item is compatible with BRAKE011

MH00015

Pillow Block Bearing 1" UCFL 205-16

.343-5-1/4-SQ-R

Cut-to-Length Square Wire Torsion Spring 31" long with Cones Right Hand

Q404

LiftMaster Omni Siren K29-50279 **to extent of inventory

SCRUBS-PAIL

Scrubs Hand Cleaning Towels 72 Towels per Pail*** Special Order Sold by Quote Only

The citrus-based formula and textured towel combination works to loosen dissolve and absorb the toughest materials
Each pail contains 72 towles
6 pails per case

CPE

Erone Proximity Card Standard *** To Extent of Inventory

Hexadecimal number printed on each badge
8mm thick

C-600-INSTALLED

Cones 6" Factory Installed (Pair)

For do-it-yourself installation use part no. SF600

7001-18-BLACK

Commercial Side & Top Weather-Strip 18' Long - Black (Code B)

Black galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

7001-10-BLACK

Commercial Side & Top Weather-Strip 10' Long - Black (B)

Black galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

7001-9-BLACK

Commercial Side & Top Weather-Strip 9' Long - Black (Code B)

Black galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

771

Fasteners Lag Screw Hex Washer High Profile 5/16" x 1-3/4" 1000/Box *** Discontinued

7/16" head

7001-7-BLACK

Commercial Side & Top Weather-Strip 7' Long - Black 7001-BB (Code B)

Black galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

767

Fasteners Lag Screw Hex Washer Regular Profile 1/4" x 1" 1000/Box ***NLA

7/16" head

761

Fasteners Flat Head Carriage Bolt 1/4-20 x 1-7/8" 1000/Box

Full length thread
Max torque = 6

774

Fasteners Hex Head Bolt 5/16-18 x 3/4" 1000/Box

5/16" bolt has 1/2" head
Max torque = 12
Full thread
Grade 2/Grade 5 depending on availability

764

Fasteners Serrated Flange Nut 5/16-18 1000/Box

Q400MAU

LiftMaster Relay Module

99554NYHNG

Nylon Hinge Black #4 *** To extent of inventory

Equivalent to 14-ga in strength.

99551NYHNG

Nylon Hinge Black #1 *** To extent of inventory

Equivalent to 14-ga in strength

MV-00025-OLD

Micanan 32-Door O/C/S Transmitter CT-32 313 MHz OLD STYLE Deep Buttons *** NLA repl by new style

Commercial / Industrial transmitter

79-11378

LiftMaster Circuit Board Assembly for LGJ **NLA - Discontinued 2015

Same as part number K79-13743

SSZP17-1

Solid Shaft 1" Keyed Zinc Plated 17'-1" ** to extent of inventory

SSZP15-1

Solid Shaft 1" Keyed Zinc Plated 15'-1" ** to extent of inventory

SSZP9-6

Solid Shaft 1" Keyed Zinc Plated 9'-6"

MT22-BLACK-RH

Miller Edge 2-Wire Pressure Sensitive Edge Sold per Foot

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Installation Manual Worksheet Sell Sheet

MT22-YELLOW-RH

Miller Edge 2-Wire Pressure Sensitive Edge Sold per Foot

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Installation Manual Worksheet Sell Sheet

19-5812

LiftMaster Trolley Chain Pack #48 for 12ft Door

Chain pack only

19-5814

LiftMaster Trolley Chain Pack #48 for 14ft Door

Chain pack only

RBH753L5-LH

LiftMaster 3/4 HP 208/230/460 VAC 3 PH Commercial Hoist Operator Logic 5

H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door.
With the addition of the 828LM MyQ technology enables the user to monitor and control their operator and light with their smartphone tablet or computer.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.
Security+ 2.0™ safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you.

.......more details

Installation Manual Manuel d'Installation Sell sheet

75-10174

LiftMaster Trolley- Front Idler Assembly

Also known as: 7510174 305115018 711150181 175017 71115211 75-10174

K72-16421

LiftMaster Limit Shaft Assembly LGO****Discontinued and no Longer available

Assembly includes: Limit shaft Limit nut Sprocket Roll pin Bushing E-Ring and Chain.

Installation Manual

CH755L5-LH

LiftMaster Hoist Op. with Carwash Mod. 3/4 HP 575 VAC 3 Ph Logic 5 Left Hand ***Replaced by CRBH755L5-RH

Industrial Duty Hoist Operator with Damp Environment modification.
Comes with CPS-UN4 photoeyes

Installation Manual Manuel d'Installation Sell sheet Brochure

K001C8103-1

LiftMaster L5 Antenna

42-31246

LiftMaster Terminal Block 20A 600V

3-position

K21-36793

LiftMaster Transformer 208-230/460 Volts 20Va

230/460V PRIMARY 24V SECONDARY 20VA

26-94625

Truck Door Top Panel (15" x 98") for Whiting DryFreight

These panels are cut to an extra wide width to fit wider vehicle applications
Interlocking tongue and groove design for weather-tight joint and proper alignment.
.75" thick 7 ply exterior grade medium density plywood
Primer finish

26-14623

Truck Door Top Panel (13" x 98") for Todco DryFreight

These panels are cut to an extra wide width to fit wider vehicle applications
Interlocking tongue and groove design for weather-tight joint and proper alignment.
.75" thick 7 ply exterior grade medium density plywood
Primer finish

MA021

LiftMaster Nylon Arm Nuts 50/Pkg

For barrier gate models MADCBB MATDCBB MASDCBB & MASTDCBB

7001-8-CREAM

Commercial Side & Top Weather-Strip 8' Long - Cream (C)

Cream galvanized steel with cream dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Also known as Almond
Full case quantity only (20)

7001-16-SANDSTN

Commercial Side & Top Weather-Strip 16' Long - Sandstone (D)

Sandstone galvanized steel with sandstone dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Also known as Taupe
Full case quantity only (10)

7001-14-SANDSTN

Commercial Side & Top Weather-Strip 14' Long - Sandstone (D)

Sandstone galvanized steel with sandstone dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Also known as Taupe
Full case quantity only (10)

165-B

Fusible Link For Loads 1 to 10 lbs

Length is 1.4328" width is .563"
Distance between center is .938"
Priced per each
Fire rated at 165 degrees Fahrenheit

MOFT20-M14-8

Carlo Gavazzi Photoelectric Sensor Thru-Beam Transmitter

Maximum sensing distance is 20 meters
11-pin
Waterproof for harsh environment i.e. water dust steam etc.
To be used with amplifier series S142.
Supplied with 15 m of shielded cable.
For receiver unit order part no. MOFR-M14-8.

.......more details

Installation Manual

K74-16420

LiftMaster Limit Switch Kit for LGO **DISCONTINUED

Installation Manual

9150000701

Safety Cable for Extension Spring 3/32" 7x7 10' Sold as a Pair

Looped on one end the other is raw (no stops)
Used to wrap around the body of an extension spring to contain the wire should the spring break.

AIRSWITCH007

Manaras Exterior Adjustable Air Switch SPDT

To be used with metal case part # AIRSWITCH008

CONSD24V

Reversing Contactor Struthers Dunn 24V

Struthers-Dunn # A275KXX90

K72-19974

LiftMaster Output Shaft Kit

Kit includes: Output shaft sprocket assembly dual sprocket 32/14 sprocket 48B18x1 sprocket 50B12x1 ring washer key set screw roll pin and thin walled receivers

Installation Manual

CLUTCH-SHAFT-AS

Lynx Complete Clutch Shaft Assembly for HDC Operators 3/4" x 17-1/2"

Fits all HDC operators - waterproof or not.

41A7619-5

LiftMaster Cover for 8355

2704.177_270

Whiting Roadside Torsion Spring 2-3/16" ID 27" Long

Torsion spring wire only
.177 wire size

K20-1075B-2LP

LiftMaster Electric Motor 3/4 HP 115/230V 1PH L3 L4 ***NLA*** Replaced by K20-1075B-2LP-H24

Standard 3/4HP 115V Logic 3 or L4 model T J HJ SD & H

12-000I

Secure Brands Keypad with Intercom Post Mount

Post mount with Intercom
RemotePro KP 26 bit wiegand output keypads
Available in three different mounting configurations: post single gang or flush.
All single gang RemotePro KP models are available with a silver aluminum faceplate.
A heavy duty metal keypad is used with all exterior models providing years of trouble free entry.
Post mount models feature a stainless steel faceplate in a heavy metal powder coated enclosure with nightlight.

.......more details

EL25G

LiftMaster Telephone Entry System Gray

Capable of accepting up to 2000 codes
4 assignable and programmable built-in relays
Mounting versatility and available in 3 colors: Gray Nickel or Silver

Installation Manual Sell Sheet

M3-2314

Marantec 4-Button Transmitter 315 MHz 97244/122468

Same as part # 65893 and 97244
Visor mount
Includes battery CR2032
Made in Germany

Instructions

BK000

Residential Top Bracket Adjustable 1-Bolt Sold per Piece

Same as part number 3-31-1
Sold per piece - not a pair

13-3510*

LiftMaster Chain Guide ***NLA

This is NLA as a part by itself but may be purchased in a kit K75-18493

11-3602_SHAFT

LiftMaster Idler Shaft (1)

Fits SL595
Two are required per operator

K20-1075C-2LP

LiftMaster Electric Motor 3/4 HP 115/230V 1Ph

M18

LiftMaster Remote Control Tester ** NLA

1005-1-3/4-10

Aluminum Bottom Retainer U-Shaped

For door thickness 1-3/4"

K75-12858

LiftMaster Clutch Kit for SL595

Kit includes: Clutch Pressure plate Torque Limiter Sprocket Assembly Bell Washer Nut Hex Jam Clutch Disc and Keyway

Replacement Instructions

MWRTA12B

Miller Edge Wireless Transmitter with Audible Alarm and 1 Channel Receiver

For 2-wire edges
Was previously MWRTA02A now has a new board making installation easier
Includes single channel receiver (MWR12A) and transmitter (MWTA12) with audible low battery alarm.
This feature that activates when the battery has only 25% of its life remaining indicating the battery should be replaced. The alarm sounds for 5 to 10 seconds at 1 to 2 minute intervals.
The receiver operates on either 12 or 24 volt AC/DC and provides N.O. or N.C. output.

OMNI-EXB

LiftMaster Relay Module

1013-1-1/4-24'

Rigid Vinyl Bottom Retainer L-Shaped 24' Long

For door thickness: 1-1/4"

302850

Linear 2-Channel Multi-Code 12-24V Gate Receiver 300 MHz / 310 MHz

The Model 302850 is a dual frequency receiver. An internal jumper selects either 300 MHz or 310 MHz operating frequency.
The 300 MHz frequency is compatible with standard Multi-Code transmitters
The 310 MHz frequency is compatible with the Stanley version Multi-Code transmitters.
Operates on 12-24 volts AC or DC power
Two channels
Whip antenna

.......more details

Programming Instructions

MDRG

Linear 1-Channel MegaCode Gate Receiver 318 MHz *** Discontinued

Activates one gate or device
Supplied with F-connector and whip antenna
Mounting bracket supplied
Memory: storage for up to 40 MegaCode transmitters
Power: 24 VAC/VDC
Codes: 1000000+ (MegaCode format)

.......more details

Programming Instructions

K75-18364

LiftMaster Arm Assembly Kit for SW470

Complete arm kit for SW470 gate operator

AW-12A

Miller Edge Air Wave Switch in NEMA 4 Enclosure

Air pressure is lead via a hose or pipe to a diaphragm contact. This contact converts the positive or negative pressure into an electrical contact and pulse.
Applications: commercial sectional doors rolling doors and mass transit
Works on doors up to 60ft
Can be used with standard pneumatic hose and Miller Edge extrusion
Sensitivity: 2mm to 500mm
Ambient temperature range: -49F to 180F

.......more details