Devanco Canada - Get The Right Garage Door Opener‎ and Parts

PHOTO-062

Manaras Monitored Photoelectric Cells N1 Thru-Beam 20' Range ** No Longer Available use PHOTO-070

Monitored NEMA 1 enclosure through-beam type photocell
4-Wire
Indoor
Range: 20 ft

38874R3.S

Genie Electronic Circuit Board Assembly

Replaces board 38001R3.S and 37470R3.S
Compatible with Genie Series 3 model 3024 garage door opener systems and Overhead Door Series 3 Model 7030

36764A

Genie Chain and Belt Pulley (#39591A)

Works on Genie IntelliG 1000 & 1200 Garage Door Openers
Both for Chain and Belt Openers
Front Idler Pulley for Genie 4024
New part number #39591A

MC00012

Micanan Gear Reducer PRO-GOHD BHC 63 40:1 56C

LVB420-11

Laminated Bumper Black 4" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

MI00003

Micanan Pocket Wheel for PRO-H/HB/LH

Comes with 3/4" bushing and 2 1/4" spring pins

CP-LX225

Lynx Enhanced Relay Board

DL91201

LiftMaster HID PROX 1346 ProxKey III *Discontinued Replaced by LMPK3-ST*

Pocket size key fob
Low cost entry level compatible with HID Prox Readers.

1013-1-1/4-10

Rigid Vinyl Bottom Retainer L-Shaped 10' Long

For door thickness: 1-1/4"

MK-00061

Micanan Time Delay on Reverse 1.5 sec. 24/110V

In closing cycle door will stop for 1.5 seconds and reverse to fully open

157370

Decorative Lift Handle Yorktown Style 8-3/4" Stamped Steel Sold per piece

Black Stamped Steel
Also known as Spade Style
Mounting hardware sold separately
Priced per each

26-40410

Truck Door T-Style Standard Side Seal 116"

Extruded from long lasting rubber
Seal protects cargo area from dirt and moisture
Used with standard J channel vertical angle with 1" track
Length: 116"
Cross reference: T #69840 W #4019 620200

1104-ASFT-9FT

Elton Aluminum Stiffener for 1104 9ft

Prevents the 1104 from buckling in the hot sun

1104-ASFT-7FT

Elton Aluminum Stiffener for 1104 7ft

Prevents the 1104 from buckling in the hot sun

MD-00030

Roller Chain #40 10' per Pack

Includes (1x) master link

29200

Doorlec Transformer 208V pr 120V sec 35VA

208V prImary 120V secondary 35VA

737

Fasteners Round Head Carriage Bolt 3/8-16 x 3/4" 1000/Box

Gr. 5 Zinc

30B530

LiftMaster Capacitor 56uF 220V ** DISCONTINUED

Same as LiftMaster # 30B620

10TD433HH1

BEA 1-Button Digital Transmitter 433 MHz

Transmitter offering means of activation of automatic doors with extended hold feature.
Delay and no-delay learn modes for either instant of delayed activation for sequencing doors.
Operating temperature: -10 to 55C
Controls one 10RD433 receiver.

EP2986

Exhaust Port 5" non latching long barrel ** Discontinued

5" inside diameter 2" sleeve - non latching.
Includes fasteners & gaskets.
Polished aluminum finish.

K75-12492

LiftMaster Brake Kit 115V Units MH

K-LA500

LiftMaster Primary Replacement Arm Service Kit for LA500 Original Arm ** DISCONTINUED

Replacement arm only - no stripes old style

2JW-D064

Rolling Steel 2" Curved Cast Windlock *** NLA

Windlocks are especially used on rolling steel doors and shutters to prevent "blow-ins" from severe storms or winds.
A wind lock is a small metal device that is attached to each slat.
Its primary function is to reduce the amount of friction that occurs between the actual door & the guiding panel.
When the wind is strong the roller door may be dislodged bent or misaligned from the guide.
With a windlock your door can operate efficiently despite wind load or pressure.
Windlocks are easy to add on to any existing rolling steel or shutter door

.......more details

342.155-CUT

Whiting Intermediate Panel Tongue & Groove 15-1/2" h Cut to Exact Length *** Price on Request

Primer only
Customer must specify exact length required

PL-B11-ARM-STR

Lynx Straight Arm for Proline Operator

Used on Proline residential garage door openers

RN0024-SS

Roller 2" White Nylon 4-1/2" Stainless Steel Stem Double Sealed Bearing

A supreme double sealed bearing roller that never requires lubrication
Ideal for high usage and high moisture areas ie..carwash
7/16" stainless steel shaft.
200 lb load 50000 cycles
UHMW tire

MK00650

Micanan UPCHARGE for N-4 Photocells in Lieu of Nema-1 Reduction for N1 Included. **Obsolete Repl by MK00697

In lieu on the standard Nema-1 photocells supplied with the operator

Installation Manual

ULT-MVP

EMX Industries Multi-Voltage Loop Detector (ULT-MVP-U)

Combines small size with 9VDC to 240VAC input range.
Size: 73 x 38 x 78mm
ULTRAMETER™ display indicates the appropriate sensitivity setting the vehicle positioned on the loop
Ten (10) sensitivity adjustments
Four (4) frequency settings
Automatic sensitivity boost (ASB) delay fail-safe/fail-secure and infinite or normal (5 min.) presence

.......more details

Operating Instructions Sell Sheet

BK314

Jamb bracket J-14 #14 12 gauge

Sold by the piece
Height 5.50" Length 1.9" Width 2.45"
Bright zinc plated 12 gauge steel
2" long track mounting slot
manufactured to accept ¼” fasteners when attaching to the track and 5/16” to lag to the wall.

MQ00012

Micanan Adjustable Cable Stopper Gold C/W Set Screw Sold per piece

Used on all Micanan waterproof and corrosion proof units that have brakes as well as all explosion proof units.
Comes with set screw 3/16” x ¼”

OPH-6232-M-N1-RH

Manaras Opera-H 1/2HP 208V 3Ph with Monitored Board and N1 Photoeyes Right Hand

Monitored version with Nema 1 photoeyes

CLUTCHPAD007

Manaras Clutch Pad 1-3/4" ID 5" OD

124772

Roller 3" UHMW Plastic 7-1/4" Stem Sealed Bearing

37845R

Genie Screw Drive Carriage Assembly

Compatible with the following models: GPower 900 TriloG 1200 TriloG 1500 PowerMax 1200 PowerMax 1500
Works with Screw Drive Shuttle assembly part # 36664R - sold seperately

375UT

LiftMaster Universal 2-btn Transmitter Next Generation

Dual frequency universal transmitter
Will activate 2 different types of openers (1 on each button)
Compatible with major brands except Marantec & Hormann
Visor clip and battery CR2032 included

Programming Instructions Instructions de programmation Sell Sheet

MX00140-110V

Micanan Brake Assembly for PRO-TB/APTB with 110V Solenoid Outside - New Model ** DISCONTINUED

18007

Doorlec Reducer BHC-63 5/8' Input

Gearbox for GH operator

754

Fasteners Self Drill & Tap Tek Screw 5/16-12 x 1" (#4PT) 1000/Box ** NLA Offer 108207

Indented Hex Washer Head
7/16" Head
Max RPM = 2000

.343-6-L

Cut-to-Length Torsion Spring .343 x 6" Left Hand Wound Blue/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED

7001-14-BLACK

Commercial Side & Top Weather-Strip 14' Long - Black (Code B)

Black galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

79-11378

LiftMaster Circuit Board Assembly for LGJ **NLA - Discontinued 2015

Same as part number K79-13743

19-5810

LiftMaster Trolley Chain Pack #48 for 10ft Door ***Actual length 24ft (288")***

Chain pack only

H501L5-RH

LiftMaster Ind. Duty Hoist Op. 1/2 HP 115/230 VAC Logic 5 Right Hand *** No Longer Available

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door.
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details

Installation Manual Manuel d'Installation Sell sheet Brochure

178B35

LiftMaster Curved / Bent Arm Kit (41B0035B)

Will work with most residential garage door openers
Also known as: 4178B0035B 178B32 41B0035B 4178B35 178B35 012385990357 178B35B

DR-312

Linear 1-Channel Delta3 Receiver 312 MHz - DISCONTINUED

312 MHz frequency 8 dip switches for coding 256 possible codes
24V AC/DC input power 3 terminal connection
Activates one device
Dimensions: 5.5" W x 4" H x 1.25" D
Same as: DNR00001

Programming Instructions

7001-16-CREAM

Commercial Side & Top Weather-Strip 16' Long - Cream (C)

Cream galvanized steel with cream dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Also known as Almond
Full case quantity only (10)

7001-8-SANDSTNE

Commercial Side & Top Weather-Strip 8' Long - Sandstone (D)

Sandstone galvanized steel with sandstone dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Also known as Taupe
Full case quantity only (20)

165-B

Fusible Link For Loads 1 to 10 lbs

Length is 1.4328" width is .563"
Distance between center is .938"
Priced per each
Fire rated at 165 degrees Fahrenheit

1104-12FT-CHARC

Residential Side & Top PVC Weather-Strip with cap 12' Long - Charcoal (H)

Charcoal rigid vinyl retainer with charcoal flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

466LMC

LiftMaster Wireless Commercial Keypad 390 MHz ** Discontinued

Up to 100 000 individual codes
Mounts to wall or gooseneck post
Incl. 6-volt alkaline battery
Illuminated stainless steel faceplate and keypad
Tamper-resistant case and "low battery" indicator
Requires 412HMC receiver

.......more details

Installation Manual Sell Sheet

K72-19974

LiftMaster Output Shaft Kit

Kit includes: Output shaft sprocket assembly dual sprocket 32/14 sprocket 48B18x1 sprocket 50B12x1 ring washer key set screw roll pin and thin walled receivers

Installation Manual

27-20113

Truck Door W-Style Spring Assembly Roadside 33" Long

Wire thickness: .182
Spring length: 33 inches long (assembled length)
Inside diameter: 1.188
Includes cable drum and bearing assembly winding cone wound onto spring for stronger desgn and internal spring spacer.

CLUTCH-SHAFT-AS

Lynx Complete Clutch Shaft Assembly for HDC Operators 3/4" x 17-1/2"

Fits all HDC operators - waterproof or not.

25605R

Genie Inner Slide Kit for Chain Drive Models

The innerslide attaches to the chain and connects the carriage to the chain
Works on the following Genie and Overhead Door models:
IC250 PMX80 PMX500-IC/B IC250/B PMX85 ALC Series PMX60 PMX300-IC/A RCD Series PMX65 PMX500IC/A PMX75 PMX-IC/B
SP99 – SP SERIES LD100-500-100A-550A LAD125-555
CM6000-6000A-60-70-80-60S
OHD-696 696CD + Others

.......more details

Q024

LiftMaster Limit Switch Assembly for SL3000 (K75-50097) *** To Extent of Inventory

Same as part number K75-50097

195LM

LiftMaster Ceiling Mount ***Discontinued***

Designed to fit most standard garages
Black powder-coated finish hides wires and cords for a cleaner look
Mounts parallel or perpendicular to rail
Adjustable height to fit most ceilings
Hangs 6.5 to 24 inches down from ceiling

Installation Manual Manuel d'Installation Sell Sheet Brochure

1A3982

LiftMaster Operator Splash-Proof Cover

For models: MH H HCT GH
For wall mounted operators 31" L x 19" W x 18" D assembly required.

Installation manual

.234-2-L

Cut-to-Length Torsion Spring .234 x 2" Left Hand Wound Blue/White

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.218-2-L

Cut-to-Length Torsion Spring .218 x 2" Left Hand Wound Yellow/Orange

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.218-2-R

Cut-to-Length Torsion Spring .218 x 2" Right Hand Wound Yellow/Orange

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

C-134-INSTALLED

Cones 1-3/4" Factory Installed (Pair)

For do-it-yourself installation use part no. SF175

.262-134-R

Cut-to-Length Torsion Spring .262 x 1-3/4" Right Hand Wound Red/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

ER100

Carlo Gavazzi Reflector 4" (100mm) Square

High quality reflector for retro-reflective photoelectric switches
Dimensions: 100 mm x 100 mm 9.2 mm thick

CR2016

Maxcell/Renata 3V Lithium Button Cell

.306_2-5/8"-LH

Torsion Spring .306 x 2-5/8" x 12ft LH Red

Wire size: .306
Inside diameter: 2-5/8"
Length: 12 ft

.234_1-3/4"-LH

Torsion Spring .234 x 1-3/4" x 12ft LH Blue/White

Wire size: .234
Inside diameter: 1-3/4"
Length: 12 ft

K75-18493

LiftMaster Chain Guide Kit

Compatible with SL575 SL585 SL595 SL595U SL595UL and IHSL
Kit includes chain guide retainers and bracket for guide holders

T-733

FL-Allstar 3-btn 3-Door O/C/S Transmitter 107477-311 MHz *** No Longer Available

This transmitter can control (open-close-stop) up to three doors.
It has a eight switches encoder with three positions: + 0 and - .
Manufacturer's model number: 733T (190-107477)
Dimensions: 6 1/4" x 3 3/8" x 1 3/8".

Programming Instructions

.295_3-3/4"-RH

Torsion Spring .295 x 3-3/4" x 12ft RH Blue

Wire size: .295
Inside diameter: 3-3/4"
Length: 12 ft

.243_3-3/4"-RH

Torsion Spring .243 x 3-3/4" x 12ft RH White/Yellow

Wire size: .243
Inside diameter: 3-3/4"
Length: 12 ft

17311

Doorlec AT1035D 1-btn Mini Transmitter 313 MHz ** To extent of inventory

One block of 10 dip-switches for programming
Compatible with Doorlec 17307 receiver (DC-3000R)
Includes 12V battery (GP23A)

MK00488

Micanan Electronic Circuit Board Monitored

Replacement board for PRO-LH (50-11)
Board has terminals P1 & P2
Up to 20 transmitters can be programmed

Instructions Manual

H14G01

Hinge #1 x 14 gauge

Bright zinc plated 14-gauge steel hinge
For use with 7/16" diameter stem rollers
Full body hinge 2-3/4" wide
#1 position
Use between sections 1 and 2 or in the center position
Same as part number 241

.......more details

LIMIT006

Manaras Single Micro Limit Switch with Flat Lever

Fits old medium-duty Manaras operators such as MDJ
SPDT - Cherry

Limit Switch Chart

LIMIT025

Manaras Single Snap-Action Limit Switch with Flat Lever

Replacement for LIMIT001
For all Manaras commercial operators prior to 2000 - except light duty models
Can be used on Doorlec Lynx and others
Unimax (SPDT)

Limit Switch Chart

DRUM006

Manaras Steel Brake Drum Flat Track - replaces DRUM001

Replaces DRUM001
Brake drum for all operators except Gear Head models prior to 1999.
Use with BRAKEPART018

RADIO-KIT005

Manaras plug-in receiver for Board 60 or electromechanical operators 390 MHz *** To extent of inventory

Direct ECB plug-in receiver card kit (RADIO RE100B) for on-site installation.
Maximum 16 transmitters per receiver.

Installation Manual

RADIO-KIT004

Manaras plug-in receiver for Board 70 operators 390 MHz

Direct ECB plug-in receiver card kit (RADIO-RE101C) for adding or replacing on-site.
Maximum 50 transmitters per receiver.
Compatible with transmitters RADIOEM101 and RADIOEM103 SD/MD

Specification Sheet

7470.115

Whiting Side Seal for insulated doors 115" Long

Fits Coldsaver and Tempguard

9931T

Allstar 1-btn Transmitter 108787 318 MHz ***Replaced by P-9931T

Compatible with Allstar and MVP receivers
Visor mounting clip supplied
Power: 9-volt battery
Codes: 19683 (set by nine trinary dip switches)
RF frequency: 318 MHz
Dimensions: 2.25" W x 4.625" H x 1" D Order number: 190-108787

.......more details

Programming Instructions

MGR

Linear 1-Channel MegaCode Gate Receiver 318 MHz (DNR00104)

��Single Form ”A” (normally open) relay rated at 30 Volts AC/DC up to 5 Amps
Supplied with whip antenna three feet of coaxial cable and bulkhead connector
Memory: storage for up to 40 MegaCode transmitters
Power: 12 - 30 VAC or 10.5 - 30 VDC
Codes: 1000000+ (MegaCode format)
RF frequency: 318 MHz

.......more details

Installation Manual

MINI-T

Linear 1-Channel Delta3 Key Ring Transmitter 310 MHz (DNT00026)

Activates one Delta-3 receiver
Test/operate LED
Key ring not supplied
Power: 12 V battery
Frequency: 310 MHz
Codes: 256 (set by dip switches)

.......more details

Programming Instructions

1209.1

Whiting Stainless Steel Truck Door Side Hinge with Roller Cover

4007-16FT

Aluminum Retainer only for Light Brush 90 degree ***Actual Length 16'2"

For angle application
For use with Light Brush or Vinyl Insert.
die # A-25060

1006-1-1/2-16'

Rigid Vinyl Bottom Retainer U-Shaped 16' Long

Black with flexible fin to touch door face.
For door thickness 1-1/2"

1006-1-1/2-12'

Rigid Vinyl Bottom Retainer U-Shaped 12' Long

Black with flexible fin to touch door face.
For door thickness 1-1/2"

1005-2-16'

Aluminum Bottom Retainer U-Shaped 16' Long***Actual Length 16'2"***

For door thickness 2"

1104-12FT-BROWN

Residential Side & Top PVC Weather-Strip with cap 12' Long - Brown (N)

Brown rigid vinyl retainer with brown flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

7001-8-WHITE

Commercial Side & Top Weather-Strip 8' Long - White (W)

White galvanized steel with white dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

1001-24-GREY

Commercial Side & Top Weather-Strip 24' Long - Grey

Aluminum retainer with grey dual-fin vinyl
Sold by full case quantity (10)

32-48-140

Extension Spring 8' Door - 140 lbs Blue ** Replaced by 27-48-140

Double - Loop
32" long 48" stretch 140 lb load
Springs sold individually

Spec Sheet

25-42-200

Extension Spring 7' Door - 200 lbs Tan

Double - Loop
25" long 42" stretch 200 lb load
Sold individually
Rated for 10000 cycles
Same as part number 120

Spec Sheet

25-42-150

Extension Spring 7' Door - 150 lbs Red

Double - Loop
25" long 42" stretch 150 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

28-02090

Truck Door 2" Vert. Track and Right Angle Assembly 96.5" Roadside (LH) for Whiting Roll-Up Doors

SPECS: Length: 96.5" Fits door sizes: 72" - 90" high
Assembly includes: Right angle mounting track Vertical track and Torsion bracket
Cross Reference: W #2275-2
Galvanized steel 14 gauge construction
Tongue and groove for proper alignment at joints

26-94523

Truck Door Intermediate Panel (13" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish