Devanco Canada - Get The Right Garage Door Opener‎ and Parts

2200-306

Linear Clutch Spring HSLG

Used on various Linear Gate operators

MEL-II-TX10

Miller Edge Monitored Edge Link-II Transmitter

Miller Edge Monitored Edge Link II TRANSMITTER ONLY
Monitors the presence and function of any 10K (T2) monitored sensing edge
Provides a monitored wireless signal transmission from the sensor to the operator controls
Improved immunity to RF interference with 916 MHz operating frequency
Eliminates visible coil cords and retracting reels
Saves installation time

.......more details

2376.192.325.930

Whiting Torsion assembly .192 wire size 32-1/2" spring length 93" shaft

This is a full balancer assembly
Twin springs one road one curb with a shaft through it

7-10-1

Double Slide Lock

MOD114A

Manaras Synthetic Oil Upgrade Only

This Upgrade Mod. is only available when purchaed with a compatible operator
Synthetic oil is placed in the operator's reducer for improved performance stability and decreased sensitivity to temperature variances

MM00082

Micanan Solenoid Support Bracket (MSI0085)

26CW945255

Truck Door Intermediate Panel (15.5" x 98") Painted White for Whiting Dryfreight

These panels are 15.50" height x 98" width.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white

106-0006

Rodent Block Pull Chain Seal 2.5"

Often overlooked and left unprotected the opening for the pull chain on dock levelers is an ideal entry point for mice and rats.
The chain provides a built-in ladder for pests and the chain opening is more than big enough for rats or mice to squeeze through.
Features solid cast aluminum construction easy to install and completely cover the chain opening.
The seals are designed to sit completely below the surface of the dock plate and will not interfere with material handling equipment.

OSH-6812-ECB

Manaras Opera-SH 1/2 HP 208V 1Ph with Electronic Circuit Board

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

GH-383-3/4

Doorlec Industrial Jackshaft Door Operator 3/4 HP 208V 3P with ECB

Custom-designed extra heavy-duty industrial-type electric door operator
Worm gear reducer 40:1 ratio
#60 roller chain and sprockets from operator shaft to door shaft.
Door speed: 7 inches per second (approx.)
Adjustable torque limiter
Rotary type limit switches

.......more details

CP-SH-58-1038-LS

Lynx Limit Shaft Only

5/8" x 10-3/8"
Used on most of Lynx operators

684-33-104-A

Universal Bracket 2.25" x 2.5" x 12" w/1" x 12" Plate

K001-KEY

Replacement Key for 3BXLT Key #1

Replacement key only for key #K001

2528.087

Whiting Dual-Spring Shaft 87" for Whiting Roll-Up Doors

Constructed of 1" outside diameter heavy-duty steel tubing
Holes pre-drilled
Cross Reference: For Whiting # 2376 balancer

K76-36296-1

LiftMaster Recepticle LA500

Only compatible with LiftMaster LA500 with standard control box

LMPC2-ST

LiftMaster HID ProxCard II 1326 26 Bit Clamshell Card Price Per Card

HID 26 Bit Format
125 kHz
Sold in Lots of 100 - Price Shown is Price per Card
Only compatible with PPLX in stand-alone mode
Please supply Start # and Facility Code # when ordering
Dimensions: 2.135" x 3.385" x 0.075" MAX. (5.4 x 8.6 x 0.19 cm)

.......more details

65-5209

LiftMaster Manual Hoist Mod. Kit #48 Chain Drive

This is an available factory installed modification only

MX00148

Micanan Complete Clutch Shaft Assembly for PRO-J

MP00215

Micanan Limit Shaft Assembly N1 H/J

37300

Decorative Pull Handle Fleur-De-Lys Sold per Pair

Cast steel
Black powder coated with smooth finish
No rotation pull handle only
Approx 7-1/2" overall length

15-10885

LiftMaster Dual Sprocket 48B10/41A24

Also known as: G1510855 156016 G156016 15-10885 15-6016 71156016

MITIS-R16

Garex Ready to Install Door Special Order

R16 Insulation - Overlay moldings positioned to create the Mitis design - Moldings are factory white or can be factory painted to match door colour - Optional decorative hardware is available - Available in steel (std colours) or aluminum (white and grey) - A variety of decorative windows can be added - Custom colours can be factory painted - Multiple hardware configurations are available to accomodate site requirements - Composite end blocks eliminates corrosion and wood deterioration

EXT-VILLERAY-R16

Garex Ready to Install Door Special Order

R16 Insulation - Overlay moldings positioned to create the Extended Villeray design - Moldings are factory white or can be factory painted to match door colour - Optional decorative hardware is available - Available in steel (std colours) or aluminum (white and grey) - A variety of decorative windows can be added - Custom colours can be factory painted - Multiple hardware configurations are available to accomodate site requirements - Composite end blocks eliminates corrosion and wood deterioration

WHTG-HINGE-TRUSS

Whiting Special Order Hinged Truss II Complete Door **POR

Special order to customer's specs
Non-wood core door
Double wall extruded aluminum panels all designed for optimum strength and appearance.
Double sealed inclined joints to stop water.
Top bottom and side seals standard.
4 rows of hinges.

.......more details

WHTG-TEMPGUARD

Whiting Special Order TempGuard Door **POR

Special order to customer's specs
1-1/2” fiberglass panels are clad with aluminum exterior facing for easy cleaning and excellent acceptance of paint and decals.
No rivets on face of door to interfere with lettering or decals.
One piece pultruded fiberglass shell featuring foam-in-place urethane insulation.
All hinge fasteners reinforced with steel backing plates.
Replaceable double seal at each panel joint.

.......more details

CP-PW-NM-MCJH

Lynx Pocket Wheel for MCJH 6"x1" Bore Long Hub

20449R

Genie Chain Glide Rear Housing Cover

Compatible with models: PCG400 PCG450 PCG500ML PCG600 PCG700ML PCG700FN GCG350L GCG350ML H2000C 1020L 2020L
Contains gear housing cover only

MIRF-T2

Miller Edge Patriot 2 Photo Eye Non-Monitored 30ft Non-Contact

Attaches directly to a Sectional door.
The photo eyes travel below the door during the closing cycle.
Unlike traditional static mount photo eyes; Patriot travels with the door sensing obstructions prior to contact.
The Patriot2 non-contact system consists of thru beam photo optics.
Emitting and receiving eyes mount into a rigid steel spring loaded retracting housing.
The housings attach to the bottom section of the door and extend below the leading edge of the door providing an invisible infrared light beam of protection.

.......more details

K77-16011

LiftMaster Hardware Kit for CPS N4

This is a replacement Sensor Hardware Kit only.

2376.206.30.870

Whiting Torsion assembly .206 wire size 30" spring length 87" shaft

ME00006

Micanan Intermediary Shaft 1" x 10-7/16" c/w KW

HD8460-KYD-ALIKE

T-Handle Cable Lock System 1-3/8"- 2" ** Keyed Alike **

Complete cable locking system for a 1-3/8" or 2" door Keyed alike
System includes: Auto Latch Striker Keeper T-Handle keyed with 4-1/4" shaft Inside release handle 3/32" cable and all required hardware.
Also works for for 1-3/4" doors
T handle KA5 = keyed alike increment of 100 (5 different combination box (20 of each #)

106141

Marantec Shaft Adapter

12-4164

Flange Mount Bearing Self-Aligning

Works with SL575 SL580 SL585 SW470.SW470 gate operator
Same as K12-4164 124164

CGH103L5-LH

LiftMaster Gearhead w/ Brake and Carwash Mod. 1 HP 208/230/460V 3-Phase Logic 5 Left Hand

Requires 828LM MyQ Internet Gateway to connect to MyQ Smartphone App.
Security+ 2.0®
Includes CPS-UN4

41ASWG-489

LiftMaster Cable Repl. Kit 24V 3m with Connector

For use with LiftMaster® Model LA400 Series Commercial Swing Gate Operators

MV00482

Micanan Banner Intrinsically Safe Reflective Photocell Kit w/Bracket & Reflector (0-25ft. Range)

Kit icludes the bracket (MV280) and reflector (MV279)
Model Q45AD9LV
Range: 9 m; Input: 5-15V dc
Output: NAMUR
2 m (6.5 ft) cable
Nema rating: NEMA 6P

.......more details

20650

Coax Cable Extension Adapter

Adapter with “F” socket
Connects two coax cables to extend length

C-24X10-134-W

Thermal Window 24" x 10" for 1-3/4" Door White

For 1-3/4" thick door

CA-104-312

Continuous Angle 1-1/2" x 3-1/2" x 104" L Sold per Piece *** NLA

12-ga angle

41D8260

LiftMaster Cover 8355W

A one piece LiftMaster® "Silver" Replacement Cover.
For use with LiftMaster® 8355W Series AC Belt Drive WiFi® Garage Door Openers

422LMC

LiftMaster 2-Channel Co-Axial Receiver 390 MHz ***DISCONTINUED

Smart Garage Door Opener® electronics on each channel for fast programming
Bell wire attached for easy second channel hook-up
18 - 35VAC/DC
FCC certified 390MHz

P-0128/LH

Autogate Retro Bracket Left Handed System

This is needed to change over to their current motor

26117

Doorlec Limit Cam Retainer Plate

Fits Most Doorlec Commercial operators except Explosion-Proof Operators
Will not fit on waterproof operators with small electrical enclosure built before 1999

27-83190

Truck Door W-Style Track and Operator 90 x 90 Door

Includes: 1 dual spring operator 2 horizontal tracks 2 vertical tracks

MG020-B-4E-P/FT

Miller Edge Sensing Edge Black 4-Wire Monitored End Outlet Sold per Foot

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

MGR20-B-2U-PER-FT

Miller Edge Sensing Edge Round Black 2-Wire Universal Outlet Sold Per Foot

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty
Non-monitored edge
Maximum length is 10ft (over 8ft requires LTL shipment at additional cost)

60-6550-C-BLK

Speed Bump Black 36" Econo Light Weight for Concrete ***NLA

A standard speed bump system section includes (2) main pieces (2) endcaps x 5” long and (1) connector clip.
Main pieces may be added and connected to form larger units.
36” long x 10.5” wide x 2” high (main piece)
EndCap: 5” Safety Snap On End Cap - sloped modular profile prevents tripping by pedestrians.
Yellow Plates: Each speed bump section is embedded with (6) yellow safety plates of weather resistant composite material for protection from salt freeze and thaw.
Can be used as a cable cover - bottom sides include 1” x 1½” channels for protecting temporary or permanent cables or hoses.

.......more details

MOTOR256

Manaras Electric Motor 1 HP 120/240V 1PH

Continous-duty base mount ODP 60Hz

4004-10FT

Aluminum Retainer only for Heavy Brush 10' Long 45 degree ** To extent of inventory

For angle application (45 degree)
For use with Heavy Brush

ULT-PLG-D-TEK

EMX Industries Ultra Loop Plug-In Loop Detector Dual Output

Trademarked Detect-on-Stop technology
Easy install with trademarked UltraMeter display with 10 sensitivity settings
Sold-state output indicating vehicle presence
Ignore cross traffic in tight spaces
Select for automatic sensitivity boost (ABS) delay fail safe/fail secure
Second output for pulse entry/exit normal/infinite presence

.......more details

Q200

LiftMaster Chain Coupling Release K07-50215

For Liftmaster trolley operator HCT

050DCDDOWF

LiftMaster Receiver Logic Board WiFi Dock Door Jackshaft

050DCDDOWF is a Receiver Logic Board Replacement Kit.
Compatible with LiftMaster® Model DDO8900W DC Light-Duty Commercial Jackshaft Operators; featuring WiFi®

PRO-GH-15011U-LH

Micanan 1.5 HP 115V 1P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

CGH151L5-RH

LiftMaster Gearhead w/ Brake & Carwash Mod. 1-1/2 HP 115/230V 1P L5 - Right Hand

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting except if a Mod is added
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

K1D8424-1CC

LiftMaster Power Board 3 Ph SL585U/SL595U

For use with LiftMaster® SL585U & SL595U Series; and various 3 Phase Commercial Slide Gate Operator Models.

CP100C

Coupler Specialty Coated 1" Bore

Coated with 1000 plus hr salt spray rated finish
1" Bore with 1/4" keyway
Malleable iron for high strength and resistance to shock loading
Coupler halves separates and is adjustable
4-(3/8"-16 x 1" square head set screws installed
Rust inhibitor coating

.......more details

2524

Whiting Balancer Bracket End - Roadside for Whiting Roll-Up Doors

Steel construction
Plain finish
Cross Reference: W #2524 for #2376 balancer

SPR41B36X11/4

Sprocket 41B36 x 1-1/4" Bore 1/4" Keyway

Same as MD-00322

SPR41B14A410B32

Sprocket 41B14-410A32 x 3/4 K0 0S w/Ollite Bushing

SHAFT120

Manaras Input Shaft for OSHW

27120

Doorlec Electric Motor 1/2HP 208/480/575V 3PH DC221

E/BLOP/371

Automatic Systems Loop Detector for Logic Board with Drive

Feig Double Channel Loop Detector Option for AS1620 which is the new logic board with drive for the BL229

SF514U-114-W

Spring Fitting 5-1/4" Winding Side Only for 1-1/4" shaft

Universal thread for use in either LH or RH wound springs.
Includes: (1) winding side only

CGH101L5-LH

LiftMaster Gearhead w/ Brake & Carwash Mod. 1 HP 115/230V 1P L5 - Left Hand

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting except when a MOD is added
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

STATION082

Manaras Push Button Control Station 2-Button Nema 4/12

2-button 2 N/O contact
Plastic

H14G03-BLACK

Hinge #3 x 14 gauge Black Powder Coated

Black powder coated 14-gauge steel hinge
For use with 7/16" diameter stem rollers
Full body hinge 2-3/4" wide
Individually wrapped

H14G01-BLACK

Hinge #1 x 14 gauge Black Powder Coated

Black powder coated 14-gauge steel hinge
For use with 7/16" diameter stem rollers
Full body hinge 2-3/4" wide
Individually wrapped

MA041

LiftMaster Mega Arm Tower Lock & Keys (No Dust Cover)

Comes with two keys

E/BLOP/005

Automatic Systems Standard Tip Support Option

SPRING040

Manaras Disconnect Spring

41A7278

LiftMaster Sprocket Kit 12-Tooth

Includes sprocket and screws

GAL.262-258-144R

delete

GAL.262-258-144L

delete

T-831

FL-Allstar Stationary TransmitterO/C/S 3-Btn 1-Door 311 MHz 107483

Open/Close/Stop stationary remote for 1 door.
Designed for commercial automatic door and gate operator applications.
This transmitter can operate a single receiver connected to one operator
Compatible with 3-channel Allstar and MVP receivers
Easy access to battery and coding switch
Power: 9-volt battery

.......more details

M15A

Safety Inertia Brake 2" Bore 13727 Torque PCM15AP

Provides a bearing to support the shaft and prevent the fall of a door if sudden acceleration occurs.
Ideal for commercial and industrial use; specifically with rolling shutters and balanced and well maintained rolling doors.
Fully resettable and reusable after lockout ocurrs.
Commonly paired with commercial safety bottom brackets in sectional door applications.
Fits 2" shaft
Note: Sectional torsion door systems must be well maintained to ensure desired inertia brake activation.

.......more details

Manual Technical data Sell sheet

JA383

FAAC Sprint 383 Board 115V

DHJ501L5-RH

LiftMaster Ind. Duty Hoist/Jackshaft Op. 1/2 HP 115/230 VAC Logic 5 Right Hand***Discontinued

Industrial-Duty Hoist/Jackshaft Operator with Internal Door Lock Sensor
Optimal for shopping mall applications with heavier rolling doors and grilles.
Provides a floor level chain hoist to ease manual operation in an emergency or power outage.
Includes a door lock sensor to prevent damage to the door and operator caused by attempts to automatically open a locked door.
Industrial Ball Bearings on 1" Output Shaft
Second Floor-Level Disconnect for Manual Lifting in an Emergency

.......more details

BCSI-PM10

Pivin Drapeau Clutch Plate for BCSI Gate Operator ** Price by Quote Only

Friction Plate

MK01428

Micanan Digital Countdown Timer

DC-Digital

50442

Doorlec Mushroom Push-Button Red for 1-Door

Capable of opening one door
NEMA 4 Enclosure

MT22-GRAY-LH

Miller Edge 2-Wire Pressure Sensitive Edge Sold per Foot Gray

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty