Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MGJ-5011U-RH

LiftMaster Medium-Duty Logic Gear-Reduced Op. 1/2 HP 115V 1Ph Right Hand

MGJ is designed for use on rolling grilles and shutters.
Maximum recommended duty cycle: 12 cycles per hour.
Heavy-duty wormgear-in-oil-bath speed reducer
3-button station for open/close/stop functionality
315 MHz radio receiver is integral to the Medium-Duty Logic board
UL325-2010 Monitored Entrapment Capability (provides primary monitored entrapment protection through monitored photo sensors: either CPS-U or CPS-UN4 or a 4-wire monitored edge using the CPS-EI interface)

.......more details

Installation manual Sell sheet

CA-104-412

Continuous Angle 1-1/2" x 4-1/2" x 104" L Sold per Piece

PRO-HHD-5011E-R

Micanan 1/2HP 115V 1P Heavy-Duty Jackshaft NM ECB No Eyes Right Hand

1/2 HP115V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Non-Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included
Emergency chain hoist with electrical cut-off for manual operation

.......more details

Installation manual Specification sheet

FD165C

Electric Motor Only 1.5 HP 110V 1Ph 56C Flange

MK00710

Micanan Varistor Harness 575V with White Wires

MM00159

Micanan Solenoid Lever HR Right

.375-6-R

Cut-to-Length Torsion Spring .375 x 6" Right Hand Wound Yellow/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED

CHAIN036

Manaras Jackshaft Drive Chain #60 - 1R10'

Includes 1 chain link

50195

Doorlec Front Idler Assembly with Shaft Trolley Models

Fits all Doorlec commercial trolley operators
Same as # 50190

MGH-6536-CONT-R

Manaras 2 HP 600V 3P Jackshaft Contactor Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

Installation manual Sell sheet

MX00137

Micanan PRO-APT Trolley Carriage with Auto Re-Engage Feature (MX00171) *** NLA

New part number is MX00171

MP00087

Micanan Track and #41 Chain for 7' h Door *Actual length 114"*

For 3/4 & 1 HP Micanan trolley operators

PRO-TB-7583-U

Micanan 3/4HP 208V 3 P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-GH-7511U-R

Micanan 3/4HP 115V 1P Gearhead Operator N1 Eyes Monitored ECB Right Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-H-5011R-LH

Micanan 1/2HP 115V 1P Hoist Operator Contactor Model Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Solenoid brake OPTIONAL

Installation manual Specification sheet

WHITING-PANEL

Whiting Special Order Replacement Panel Only Price by Quote Only

Special order to customer's specs

PRO-H-5011U-RH

Micanan 1/2HP 115V 1P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

Installation manual Specification sheet

9271431440

Spring Wire .289 x 2.625 x 144" Coated RAW LH

.289 x 2-5/8" x 12'

2806.192.340

Whiting .192 x 2-3/16 x 34" Roadside with Cones

.273-334-L

Cut-to-Length Torsion Spring .273 x 3-3/4" Left Hand Wound Orange/Red

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

PRO-H-5053U-LH

Micanan 1/2HP 575V 3P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

Installation manual Specification sheet

503267

PEEK Vehicle Loop Detector 24V with Harness Nema 1 ** Discontinued

Enclosed requires separate 24VAC power.
Wiring harness with plug for detector included.
OPEN only (all LiftMaster operators) or SAFETY/HOLD OPEN only (operators with type B2 T TS or T1 control wiring) when vehicle passes over loop wire
Requires a loop of wire embedded in the ground to connect to the detector.
Requires 2-wire output connection to door operator and 24VAC power
Also known as: G50625S24

.......more details

PRO-TB-7553-U

Micanan 3/4HP 575V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks
Full function Smart 10.0 logic control board featuring on-board receiver
#41 roller chain drive
Solenoid brake standard
External radio control strip
Three button O/C/S control station Nema-1 included

.......more details

18002

Doorlec Reducer #80

41A5047

LiftMaster Door Bracket Kit

Also known as: 12C582 12B198 12B374 062265 41A5047 12B374-2
Includes door bracket clevis pin and lock ring

P220-3K

Heddolf 3-btn Transmitter 8-Dip Switch 318 MHz

Allstar compatible remote

P220-1K

Heddolf 1-btn Transmitter 9-Dip Switch 318 MHz

318MHz single button 9 trinary dipswitch remote control transmitter
Compatible with Allstar and Pulsar
Compatible with P294-K receiver

2376.171_22.840

Whiting Torsion assembly .171 wire size 22" spring length 84" shaft

E3JM-30FT

Omron Thru-Beam Photoelectric Sensor Nema 4 0-30ft Range

Easy-to-wire terminal block
Built-in timer offers selectable ON-delay OFF-delay and one-shot
Relay or transistor output models
Light-ON/Dark-ON operation switch selectable
Model: E3JM-10M4-US

ME00001

Micanan Limit Shaft 3/8-1/2 x 9.75"

2376.206.35.930

Whiting Torsion assembly .206 wire size 35" spring length 93" shaft

MGH-6115-ECB-RH

Manaras 1.5 HP 120V 1P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

Installation manual Sell sheet

GRC390/315-3

Heddolf Genie Compatible 390 or 315 MHz 3-btn Transmitter

390 or 315 MHz rolling code compatible 3-Button 3-Channel remote transmitter
Works with Genie and Overhead Door openers that utilize a ROLLING CODE 315 or 390 MHz
Compatible with Genie model GIC-3 GIT90-3 GIT-3 GIT-3BL G2T-3 G2T-3BL GICT390-3BL ACSGT ACSCTG Type 1 ACSGT Type 1 TBSTG Type 1 Series II Electronics Compatible Remote and B8QACSC

.312-334-R

Cut-to-Length Torsion Spring .312 x 3-3/4" Right Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

MB-03204

Micanan Electric Motor Only 1 HP 575V 3PH C-Flange TEFC 56C

Fits GT GH GHC & GSD

108D79

LiftMaster Light Lens 108D0079M

Replaces 108D68 and 108D68-1

DS75-SEAL

Bottom Seal for DS75 Mini Storage Door Grey

The seal is available in 100-foot rolls but we are selling it by the foot for your convenience.
These seals help prevent wind and weather from having an effect on the interior of the garage.
Blade astragal

1A4324

LiftMaster Steel Angle Hood Mount Bracket

Heavy-gauge steel bracket used for vertical or horizontal mount for either front or top of coil mount.
May be welded.
For use with LiftMaster Model DJ DH MGJ GH J and H.
Cannot be used with Model GH 3HP.

MG020-B-2E-05

Miller Edge Sensing Edge Black 2-Wire End Outlet 5ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

MG020-B-2E-04

Miller Edge Sensing Edge Black 2-Wire End Outlet 4ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

42RLU-4003B

Allen Bradley Retro Reflective Photoelectric Sensor Long Range 24V *** Discontinued

Infrared photocell
Sensing distance: 35ft
Output type: DPDT EM Relay
Operating voltage: 18-28V AC 20-32V DC

25050

Doorlec Explosion Proof 3-Btn Pushbutton Control Station

CSA and UL labeled station
Three button O/C/S Nema-7/9
Surface mount
Rated: Class 1 Division 1 Groups C.D.E.F.G.

K94-37236

LiftMaster Universal Solar Harness Kit

For 7 Ah and 33 Ah batteries

GD-STEND-18D

End Cap Steel 18G 18" Double 1-3/4"

GD-STEND-21D

End Cap Steel 18G 21" Double 1-3/4"

39438R

Genie Garage Door Opener LED Bulb LEDB1-R 1/Pkg

Unlike other LED and CFL bulbs this bulb will reduce or eliminate radio frequency interference
Uses 10 watts but equivalent to a 60-watt bulb
Works with almost all garage door openers
Lasts up to 25000 hours
Shatter-resistant vibration-resistant
Cold weather rated up to -30C

.......more details

C-24X12-134-W

Thermal Window 24" x 12" for 1-3/4" Cedo Door White

For 1-3/4" thick door

2806.156.195

Whiting .156 x 2-3/16 x 19.5" Roadside with Cones

MIRM-T2-50

Miller Edge Patriot 2 Photo Eye Monitored 50ft Non-Contact ** Discontinued

Attaches directly to a Sectional door.
The photo eyes travel below the door during the closing cycle.
Unlike traditional static mount photo eyes; Patriot travels with the door sensing obstructions prior to contact.
The Patriot2 non-contact system consists of thru beam photo optics.
Emitting and receiving eyes mount into a rigid steel spring loaded retracting housing.
The housings attach to the bottom section of the door and extend below the leading edge of the door providing an invisible infrared light beam of protection.

.......more details

PRO-LH-5011R-LH

Micanan 1/2HP 115V 1P Medium-Duty Jackshaft with Contactor Left Hand (PRO LHR)

Designed for use on commercial sectional doors with high or vertical lift
May also be used on small rolling grilles with max. 15 cycles per hour
Includes chain hoist
Includes solenoid brake
No longer available in contactor model (2017)

Installation manual Specification sheet

.343-514-L

Cut-to-Length Torsion Spring .343 x 5-1/4" Left Hand Wound Blue/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-525-INSTALLED
If cones are required a filler must be added use part # FILLER

SLR-221

Linear Residential Slide Gate Op. 1/2HP 230V 1 Ph - Cold Weather Package NOT Included

Integral entrapment sensing system with digital set point for quick accurate adjustment and enhanced safety
Continuous-tone entrapment alarm with reset button
LED diagnostic display for ease of setup and troubleshooting
Selectable pre-start and run alarm with provision for ADA compliant visual pre-start and run alarm
Regulated 24 Volt DC power available for access control accessories
Integrated maximum run and auto close timer (0-9 minutes)

.......more details

9-24-1

Lynx BarLock Mounting Plate

Assembly Manual

K002B0821-1

LiftMaster Transformer for EL1SS and EL25

120 volt input power plugs into a standard outlet
16VDC output 2.5 amps

CABLE-NR-316-SS

Cable No Roll 3/16" 19x7 Stainless Steel 500ft

19X7 SS 3/16” Rotation-Resistant Wire Rope was conceived for overhead cranes but manufactured specifically for high-performance garage doors.
A spin-resistant construction coupled with the corrosion-resistance of stainless steel is the perfect mix of resilience and performance for high-traffic areas.

MGH-6114-ECB-LH

Manaras 1 HP 120V 1P Jackshaft with Elect. Circuit Board Left Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

Installation manual Sell sheet

MGH-6114-ECB-RH

Manaras 1 HP 120V 1P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

Installation manual Sell sheet

220315

Allstar Challenger Gear & Sprocket with Bushing

19863R

Genie Clip and Collar Rail Connectors

For Genie screw drive units having split rails use a collar and spring clip to join the 3-piece screw.
Complete collar and clip set for one 3-piece rail.
Compatible with all screw drive Genie garage door openers
Set of 2 clips and 2 collars
Same as 19806A04 and 19807A04

PRO-HBH10011U-R

Micanan 1 HP 115V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand (Pro-HHD)

1 HP115V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

41D7570

LiftMaster Light Lens (41D7572)

Also known as 041D7572 41D7571 41D7570 41D7572 041D7571 041D7570 041-0144

PRO-H-7511U-RH

Micanan 3/4HP 115V 1P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

Installation manual Specification sheet

LM21XPBBVB

LiftMaster Extended Performance Fire Door Release Device with Battery Backup and Voice Board ** No Longer Available

UL864 Revision 9 compliant
Programmable DIP switch delay setting - either 10 20 30 or 60 seconds delay of door release to permit passage clearance
Inputs for normally open 2- or 4-wire detectors and 4-wire normally closed detectors
Trouble and alarm relays for communication with the fire alarm control panel if required
Audible trouble sounder to indicate when the release device is not operational
On board diagnostic LEDs for easy troubleshooting

.......more details

Installation manual

24-230-5

Relay 3 PDT 230V 7A

208/230VAC relay
Used in BG770 gate operators

Q084

LiftMaster Cam Lock and Keys HCT K80-50142

Same as K80-50142
Fits model HCT
Comes with 2 keys

PPLV1-10

LiftMaster Passport Lite 1-Button Visor Remote with Sec+ 2.0 Technology 10/PKG

Passport Lite Remote Controls provide cost-effective single button access solutions for gate access only or high-capacity commercial properties applications such as employee parking lots and tenant garages.
These remote controls are specifically designed for gate access control and are not compatible with LiftMaster Garage Door Openers.
2x the range of standard remote controls
Narrow-band transmission on 3 simultaneous frequencies (310 MHz 315 MHz 390 MHz)
Compatible with LiftMaster® commercial receivers (850LM 860LM PPWR STAR1000) and Security+ 2.0™ Gate Operators
Sold in a 10 pack

.......more details

Programming instructions Instructions de programmation Sell sheet Brochure

SF514U-114

Spring Fitting 5-1/4" Pair for 1-1/4" shaft

Universal thread for use in either LH or RH wound springs.
Pair includes: (1) winding 1-1/4"bore & (1) stationary 1" bore.

15-50B12LGH

Sprocket 12 Teeth 1" Bore 1/4" Keyway

Same as 50B12x1

PRO-HBH-10023U-L

Micanan 1 HP 230V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand (Pro-HHD)

1 HP230V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

PRO-HBH-10023U-R

Micanan 1 HP 230V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand (Pro-HHD)

1 HP230V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

27-20010

Truck Door Dual-Spring Shaft 96" for Whiting Roll-Up Doors

Constructed of 1" outside diameter heavy-duty steel tubing
Holes drilled in one end only for cotter pins the other end is not drilled for flexibility
Cross Reference: W #2528

27-20003

Truck Door Dual-Spring Shaft 87" for Whiting Roll-Up Doors

Constructed of 1" outside diameter heavy-duty steel tubing
Holes drilled in one end only for cotter pins the other end is not drilled for flexibility
Cross Reference: W #2528

3-32-1

Low Headroom Top Bracket 2" Residential

For residential door with 2" track

CL-74-RH

Wayne Dalton Complete Replacement Barrel Assembly 4.5" Diameter 74" Long

Replacement for serial # 10093517-1 PIPESM

12575

Doorlec Clutch Disc Fiber 4" dia.x 5/8" bore

Fits model LJ / LJH

5735.96

Whiting Bottom Seal Grey 96"

For Dry Freight and Truss Doors

KPX-100

EMX Access Control Keypad

Stainless steel face with metal backlit keys
Anodized and powder coated steel outer housing that is vandal and weather resistant to IP66 (all weather)
Dual relay outputs
Over 100 Million 4-8 digit codes
12-24V AC/DC operation
100 user codes on Relay 1; 10 users relay 2

.......more details

SF375-DUPLEX

Spring Fitting 3-3/4" Stationary Side Only for Duplexing (Short Ear). *** Not Sold As A Pair

To make duplex assemblies you require one pair of SF600 (W & S) and only two SF375-DUPLEX stationary plugs only no need for P375 winding plugs

K75-10259

LiftMaster Track Spacer Assembly

Standard duty trolley operator part

TUBE_SHAFT_12FT

Hollow Shaft 1" x 12'-10" Galvanized 16 gauge

When ordering order one foot longer that actual door width

CS303-DB100

EMX Car Sense Direct Burial Sensor with 100 ft Lead Wire *** Replaced by LRS-DB-100

Can be used for above ground applications ie.. strapped to a post or wall
Easy low cost installation
Small size of the detector allow for easy installation in pavement
Rugged sensor is also suitable for above grade installations
Includes direct burial sensor and 100 ft of lead wire
Advanced 3-axis technology for better detection

.......more details

6X16SC50

Devanco Loop 6' x 16' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation manual Manuel d'installation Loop placement guide Guide de positionnement des boucles

4X20PO50

Devanco Loop 4' x 20' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

XT2564-CUT

Xcluder Rodent Block 4" Black Sold per Foot

For commercial and residential applications
Creates a tough barrier that is virtually impenetrable to rodents

Sell Sheet

K20-1050B-2TLP

LiftMaster Electric Motor 1/2 HP 115/230V 1Ph L3 L4 TEFC

TAPS1458W

Stainless Hinge Screw 1/4" x 5/8" Self-Threader with Washer

Priced per each

LM21XP

LiftMaster Extended Performance Fire Door Release Device

UL864 Revision 9 compliant
Programmable DIP switch delay setting - either 10 20 30 or 60 seconds delay of door release to permit passage clearance
Inputs for normally open 2- or 4-wire detectors and 4-wire normally closed detectors
Trouble and alarm relays for communication with the fire alarm control panel if required
Audible trouble sounder to indicate when the release device is not operational
On board diagnostic LEDs for easy troubleshooting

.......more details

Installation manual