Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MDT-4B

Linear 5-Channel Visor Transmitter MegaCode Block Coded 318 MHz

Compatible with all Linear access receivers and controllers
Superior transmission range
Unique ”Extra” top button
High visibility operate LED
Visor clip included
Sold in lots of 10

.......more details

Programming instructions

MX00145

Micanan Brake Assembly for PRO-APT Solenoid NOT included ** DISC

Discontinued. Use part number MX00140

32-34792

LiftMaster Gear Reducer Nema 56C 30:1

Compatible with LiftMaster® Model SL585 Slide Gate Operators
Same as K32-34792

R5995

Shaft Collar 1-1/4" Double Split

4X16SC50

Devanco Loop 4' x 16' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation Instructions Instructions d'installation Loop Placement Guide Guide de positionnement des boucles

26-945255

Truck Door Intermediate Panel (15.5" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish

K72-19975

LiftMaster Clutch Shaft and Sprocket Assembly

Assembly includes: Clutch shaft 1" keyed flange bearings Dual sprcket 32/14 Splined core sprocket E-ring Compression spring Pulley assembly Washers Thrust bearing Retaining ring Slined hub and roll pin
Compatible with DJ J operators

RESET007

Manaras Resettable Overload Fuse 10A 1 Phase

157370

Decorative Lift Handle Yorktown Style 8-3/4" Stamped Steel Sold per piece

Black Stamped Steel
Also known as Spade Style
Mounting hardware sold separately
Priced per each

CB18A500-KOR

Cable 1/8" 7x7 500' Galvanized Supreme

Galvanized cable 1/8" 7x7 500ft spool.
A higher quality cable than the Chinese cable.
Meets endurance test requirements of over 35000 work cycles
Lubricated for flexability and longer service life

Comparison charts

K20-1075B-2P

LiftMaster Electric Motor 3/4 HP 115/230V 1Ph Contactor Model

361LMC

LiftMaster 1-btn Digital Transmitter 315MHz ***No Longer Available

9 dip switch 315MHz transmitter
Compatible with Commercial operators L3 & L4
Visor clip and battery included (GP23A)

Programming Instructions Instructions de programmation

MAW123-BLK-LH

Miller Edge Air-Wave Edge Black Sold per Foot

This pressure sensitive air-wave edge can be adapted to suit a wide variety of applications.
When touch activated the MAW123 sends an immediate pulse of air through the extrusion to an air-wave switch which sends a signal to controls to stop and/or reverse operations.
It has been designed to fit most doors with double track bottom retainers.
With appropriate mounting channel this edge will fit nearly all doors from 11/2" to 2" thick.
The MAW123 is resistant to flame water and most common greases and oils.

MD-00057

Sprocket 50B36 1" shaft 1/4" KW

36 tooth sprocket for #50 chain

S142ARNN924

Carlo Gavazzi Amplifier 24V

Processor controlled amplifier for one set of photoelectric sensors type MOFTR.
11-pin circular plug for easy connection.
8A SPDT relay output NPN/ PNP transistor output or alarm output.
Diagnostics for sensor test during operation.
Alignment help via LED or alternation of alarm output.
Level indication for dirt accumulation.

.......more details

Installation Manual

ME123-C3

Miller Edge L-Shaped PVC Mounting Channel Sold by the Foot

2" Wide 1-1/4" High

1104-8'-DES-SAN

Residential Side & Top PVC Weather-Strip with cap 8' Long - Desert Sandstone

Garaga desert sandstone rigid vinyl retainer with Garaga desert sandstone flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

11-10987

LiftMaster Clutch Shaft for MH

14JW

Rolling Steel 3" Flat Cast Endlock

Endlocks are riveted to curtain slats ends of every other slat to prevent slats from shifting laterally and to prevent curtain wear in guides.
Continuous endlocks are both ends of every slat.
Rivets included with endlocks

342.115-CUT

Whiting Intermediate Panel Tongue & Groove 11-1/2" h Cut to Exact Length

Primer only
Customer must specify exact length required

340.115-CUT

Whiting Top Panel Tongue & Groove 11-1/2" h Cut to Exact Length

Primer only
Customer to specify exact length

GH501-L5

LiftMaster Gearhead with Brake 1/2HP 115/230V 1P L5 ***No Longer Available

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting.
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

Installation Manual Manuel d'Installation Sell sheet Brochure

SL532COP

Copper Sleeve 5/32" 100 Sleeves per Pkg *price on request

Oval sleeves ONLY
Stops sold separately part # ST532COP

.343-3-3/4-RH-C

Torsion Spring .343 x 3-3/4" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .343 ID: 3-3/4" Length: 12 ft

.319-6-RH-C

Torsion Spring .319 x 6" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .319 ID: 6" Length: 12 ft

.312-3-3/4-RH-C

Torsion Spring .312 x 3-3/4" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .312 ID: 3-3/4" Length: 12 ft

.306-2-5/8-LH-C

Torsion Spring .306 x 2-5/8" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .306 ID: 2-5/8" Length: 12 ft

.283-2-LH-C

Torsion Spring .283 x 2" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .283 ID: 2" Length: 12 ft

Q310

LiftMaster Surge Protection for MIR-1 ( K74-50271) ** DISCONTINUED

For the Miracle-One single arm gate operator
Same as part no. K74-50271

LEVER056

Manaras Disconnect Lever

Works on newer model MJH

ME00028

Micanan Input Shaft Heavy-Duty

790

Fasteners Hex Nut 3/8-16 1000/Box

29-31229

LiftMaster Relay 24VDC 30A SPDT 1-Phase only

C-relay for model T operators 10A

915007048X

Extension Cable 1/8" 7x19 14' Sold as a Pair

Cable assembly for extension spring door - looped on one end the other is raw (no stops)

9150000670

Extension Cable 1/8" 7x7 14' Sold as a Pair

Cable assembly for extension spring door - looped one one end the other is raw (no stops)

1104-16FT-CHARC

Residential Side & Top PVC Weather-Strip with cap 16' Long - Charcoal (H)

Charcoal rigid vinyl retainer with charcoal flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

1104-14FT-GREY

Residential Side & Top PVC Weather-Strip with cap 14' Long - Grey (G)

Grey rigid vinyl retainer with grey flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

71-65WTC

LiftMaster Weatherproof Case (71-65WTBOX)

Optional weatherproof case suited for 412LMC 422LMC and 423LMC
Measurements of the interior: W=5.75" L=7" D=3"
Measurements of the exterior: W=7" L=10" H=3.5"

SEDK2641A4

Erone Wireless Radio Keypad 433 MHz

Wireless RF Digicode® keypad.
Frequency: 433.92 MHz.
For automatic door opening in sequential mode.
6 channels to control 6 different relays or 6 different RF receivers.

Programming Instructions Wireless System Chart

K-73BG770-3311

LiftMaster Service Kit E-Box for BG770

MDT-4A

Linear 5-Channel Visor Transmitter MegaCode 318 MHz

Compatible with all Linear access receivers and controllers
Superior transmission range
Factory programmed MegaCode format supports over 1000000 codes
Unique ”Extra” top button
High visibility operate LED
Visor clip included

.......more details

Programming Instructions

02-401

Push Button Control Station 1-Button Surface Mount NEMA 1

Die-cast metal enclosure
START may be used as OPEN with all LiftMaster operators.
May be used as OPEN and CLOSE on all operators with type B2 control wiring

DS-KIT

Linear Single Delta Radio Kit ** Discontinued

Kit includes one DT transmitter and one DR receiver
Same as: DNP00011
Operates on 24 VAC power
One channel
Codes: 1024 (set by dip switches)
RF frequency: 310 MHz

.......more details

Installation Manual

41A7756

LiftMaster End Panel with Light Socket for 8557

.243-134-R

Cut-to-Length Torsion Spring .243 x 1-3/4" Right Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

2806.139*140

Whiting Spring Assby .139 x 2-3/16 x 14" L Roadside

Replacement torsion spring with cones for Whiting Door Serial # 138631
Specs: .139 x 2-3/16" x 14" Long
Roadside
For Curbside order part # 2807.139.140

7001-12-W/B

Commercial Side & Top Weather-Strip 12' Long - White and Black (WB)

White galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (10)

.406_6"-LH

Torsion Spring .406 x 6" x 12ft LH Blue/Yellow

Wire size: .406
Inside diameter: 6"
Length: 12 ft

.421_6"-LH

Torsion Spring .421 x 6" x 12ft LH Gold

Wire size: .421
Inside diameter: 6"
Length: 12 ft

.363_6"-LH

Torsion Spring .363 x 6" x 12ft LH Green/White

Wire size: .363
Inside diameter: 6"
Length: 12 ft

.468_5-1/4"-LH

Torsion Spring .468 x 5-1/4" x 12ft LH Blue/Orange **NLA

Wire size: .468
Inside diameter: 5-1/4"
Length: 12 ft

.319_5-1/4"-LH

Torsion Spring .319 x 5-1/4" x 12ft LH Blue/Green

Wire size: .319
Inside diameter: 5-1/4"
Length: 12 ft

.283_5-1/4"-LH

Torsion Spring .283 x 5-1/4" x 12ft LH White

Wire size: .283
Inside diameter: 5-1/4"
Length: 12 ft

.437_3-3/4"-LH

Torsion Spring .437 x 3-3/4" x 12ft LH Red/Green

Wire size: .437
Inside diameter: 3-3/4"
Length: 12 ft

.393_3-3/4"-LH

Torsion Spring .393 x 3-3/4" x 12ft LH Orange

Wire size: .393
Inside diameter: 3-3/4"
Length: 12 ft

.363_3-3/4"-LH

Torsion Spring .363 x 3-3/4" x 12ft LH Green/White

Wire size: .363
Inside diameter: 3-3/4"
Length: 12 ft

.343_2-5/8"-LH

Torsion Spring .343 x 2-5/8" x 12ft LH Blue/Red

Wire size: .343
Inside diameter: 2-5/8"
Length: 12 ft

.243_2-5/8"-LH

Torsion Spring .243 x 2-5/8" x 12ft LH White/Yellow

Wire size: .243
Inside diameter: 2-5/8"
Length: 12 ft

.273_2"-LH

Torsion Spring .273 x 2" x 12ft LH Orange/Red

Wire size: .273
Inside diameter: 2"
Length: 12 ft

.295_1-3/4"-LH

Torsion Spring .295 x 1-3/4" x 12ft LH Blue

Wire size: .295
Inside diameter: 1-3/4"
Length: 12 ft

.262_1-3/4"-LH

Torsion Spring .262 x 1-3/4" x 12ft LH Red/Yellow

Wire size: .262
Inside diameter: 1-3/4"
Length: 12 ft

.437_6"-RH

Torsion Spring .437 x 6" x 12ft RH Red/Green

Wire size: .437
Inside diameter: 6"
Length: 12 ft

.468_6"-RH

Torsion Spring .468 x 6" x 12ft RH Blue/Orange **NLA

Wire size: .468
Inside diameter: 6"
Length: 12 ft

.283_6"-RH

Torsion Spring .283 x 6" x 12ft RH White

Wire size: .283
Inside diameter: 6"
Length: 12 ft

.437_3-3/4"-RH

Torsion Spring .437 x 3-3/4" x 12ft RH Red/Green

Wire size: .437
Inside diameter: 3-3/4"
Length: 12 ft

.262_2-5/8"-RH

Torsion Spring .262 x 2-5/8" x 12ft RH Red/Yellow

Wire size: .262
Inside diameter: 2-5/8"
Length: 12 ft

2705.162_180

Whiting Curbside Torsion Spring for Cube Truck Roll-Up Doors 18" Long Galvanized

Most common torsion spring for cube trucks
Specs: .162 x 2-3/16" x 18" Long
For Roadside order part # 2704.162*180

2237.096

Whiting Coldsaver Intermediate Panel 13-1/2" x 96"

Fits Coldsaver Roll-Up Doors
1-1/8" thick 96" wide

7176.225_31.93

Whiting Heavy Duty Torsion Assembly .225 x 31" shaft 93"

7176.225_31.910

Whiting Heavy Duty Torsion Assembly .225 x 31" shaft 91"

1009-1-3/4"

Bottom Nail-On for Wood Door Heavy Duty per foot

For 1-3/4" commercial doors.
Color: Black

1019-1-3/8-10'

Rigid Vinyl Bottom Retainer Flat 10' Long

Black - for door thickness of 1-3/8"

1014-1-5/8-24'

Rigid Vinyl Bottom Retainer Notched 24' Long

Black - for door thickness of 1-5/8"

1014-1-5/8-12'

Rigid Vinyl Bottom Retainer Notched 12' Long

Black - for door thickness of 1-5/8"

1006-2-16'

Rigid Vinyl Bottom Retainer U-Shaped 16' Long

Black with flexible fin to touch door face.
For door thickness 2"

1003-1-3/8-10'

Aluminum Bottom Retainer L-Shaped

For 1-3/8" thick doors.

27-20200

Truck Door Winding Plug for Todco Roll-Up Doors

Cast aluminum construction.
Provides easy method to adjusting spring tension.
Cross Reference: T #59158 T #51041 W #4050 340100

26-94525

Truck Door Intermediate Panel (15" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish

26-14323

Truck Door Bottom Panel with Seal (13" x 98") for Todco DryFreight Doors

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish
Comes only with bottom retainer and seal (installed)

R5201

Cast Iron Pulley 3"

Bored for 3/8" diameter bolt
Cable diameter: 1/8"
Cast iron pulley mounted on two pressed sealed bearings.
Radial Load: 400lb

4X6SC50

Devanco Loop 4' x 6' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation Instructions Instructions d'installation Loop Placement Guide Guide de positionnement des boucles

26-14625

Truck Door Top Panel (15" x 98") for Todco DryFreight

These panels are cut to an extra wide width to fit wider vehicle applications
Interlocking tongue and groove design for weather-tight joint and proper alignment.
.75" thick 7 ply exterior grade medium density plywood
Primer finish

ME00057

Micanan Clutch Shaft Only for PRO-APT 3/4" x 12-3/4"

For model PRO-APT

5464.96

Whiting Top Seal Coldsaver 96" L 2-3/16" W

41D8198

LiftMaster End Panel with all Labels and Light Socket

End panel works with various models

25E10270

Truck Door Shaft Cover for Bottom Roller Black E-coat finish for Whiting Roll-Up Doors

Steel construction Black E-coat finish
Attaches to bottom panel for roller support
Shaft cover for 1 stud
Cross Reference: W #1021

70.32

Whiting Stainless Steel U-Bolt 1-1/4"

Sold per U-bolt

2705.192_340

Whiting Curbside Torsion Spring 2-3/16" ID 34" Long

Torsion spring wire only
.192 wire size

STATION086

Manaras 3-btn Push-Button Control Station Nema 1 Flush Mount

2 N/O contacts and 1 N/C contact for stop.
Flush mount.

GALV-295-258-144-L

Torsion Spring .295 x 2-5/8" x 12ft LH Galvanized Blue

Wire size: .295
Inside diameter: 2-5/8"
Length: 12 ft
Galvanized Stenciled

71-B575H

LiftMaster Interior Brake Kit with Cable 575V (Logic 3 4 and early 5 Disc and Pad Models)

Interior mount brake kit for operation with chain hoist
Includes solenoid

Instruction Manual

SN1600341-K

LiftMaster Sentex Bypass PCB for TAC1 EL25

BY PASS Board for 1150051
Same as KSN1600341B

10.1002.23

Truck Door Rivet with Splines 1/4" x 1-1/32" Stainless Steel

Stainless steel construction
Round head design 11/16" head

1005-1-3/4-14

Aluminum Bottom Retainer U-Shaped

For door thickness 1-3/4"

.312-5-1/4-RH-C

Torsion Spring .312 x 5-1/4" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .312 ID: 5-1/4" Length: 12 ft

PRO-TB-10043-U

Micanan 1 HP 460V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters