Devanco Canada - Get The Right Garage Door Opener‎ and Parts

GX-200-MG

Garex Ready to Install Door Multi-Grooved Special Order

21" panel = 4 grooves 24" panel= 5 grooves
COMPLETE JOINT SEAL No air circulation between the panel sections eliminating thermal bridges.
Minimize the heat transfer between the inside and outside of your garage.
LIGHTWEIGHT AND ROBUST PANEL Polyurethane foam insulation pressure injected between the interior/exterior faces
WOOD END BLOCKS Suitable to receive steel end caps
HIGH-PERFORMANCE DESIGN Flexible rubber inserted into a PVC reinforced moulding offering a tightly sealed fit to the floor

.......more details

OSH-6532-M-N1-LH

Manaras Opera-SH 1/2HP 600V 3Ph Monitored w/ N1 Eyes Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation brake and a floor level engaging device
Clearence: side room required 16"

8087.207.320

Whiting .207 x 2-5/8 IN x 32" Curbside with Cones

An original Whiting assembly

GALV-406-6-L

Cut-to-Length Torsion Spring .406 x 6" Left Hand Wound Galvanized Blue/Yellow Price per Inch

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED
Galvanized

DWI-LOCK

Doorway Impact Monitored Slide Slock V2

Monitored Slide Lock for the DoorWay Impact Sensor (Impact sensor and air switch not included)
Connects to an Air/Impact switch to mechanically and electrically lock the door.

E/0172/166

Automatic Systems Spring Assembly

MOD050N2

Manaras Friction Clutch Mod. #50 Chain 1-1/4 RGH

Installed directly on the output shaft of the operator.
Provides added protection by causing the clutch to slip when the door systems requires adnormal torque to be operated.
Includes sprocket for #50 chain
Operator mounting side must be specified
A spreader bar cannot be used in conjunction with this modification
This modification applies to RGH ops

.......more details

22019

Doorlec Push Button Contact Block N/O

PL-A26-LENS

Lynx Front Light Lens LPL 455+

44-60-160

Extension Spring 10' Door - 160 lbs

Clipped ends
44" long 60" stretch 160 lb load

K80-5001

LiftMaster Keyway 3/16 x 3/16 x 1-3/4"

For use with various LiftMaster® Gate Operators and Perimeter Access Solutions

E/1929/023

Automatic Systems Balance Spring Ass'y 5.5 MM BL229

Used on the BL229 gate op.

MODKIT027

Manaras Universal Aux. Output Module B060 Field Install

MODKIT027 for field install simply plugs into the control board
Controls several auxiliary devices such as Strobe horn fan lights etc
Works with BOARD060
Can only be used on operators with BOARD060 pre-installed for operators built prior to October 14 2010.

10PBR45LL

Push Plate S/S 4.5" Round Large Logo

Compatible with 900 433 and 300mhz.
May be hardwired to the operator or connected to BEA transmitters.

71-B1PH-1

LiftMaster Internal Brake Kit w/Solenoid 120/240V 1PH for SL585U/SL595U

This is a replacement Internal Brake Solenoid (120/240V SL585U/SL595U). Compatible with LiftMaster® Models SL585U and SL595U Slide Gate Operators.

15-50B32LGH

Sprocket 50B32 1" shaft 1/4" KW

71-1550B32LGH is a 32 Tooth Sprocket Kit 1" Bore x 1/4" keyway (50B32).
For use with various LiftMaster® Logic 4.0/5.0 and MAXUM DC Standard-Duty and Industrial-Duty Commercial Door Operators

15-50B32QGH

Sprocket 50B32 1.25 Bore 1/4" w/SS

71-1550B32QGH is a 32 Tooth Sprocket Kit 1-1/4" Bore x 1/4" keyway (50B32-114)
For use with various LiftMaster® Logic 4.0/5.0 and MAXUM DC Standard-Duty and Industrial-Duty Commercial Door Operators

CAPXSTK

LiftMaster Trim Kit for CAPXS

Trim plate exclusively for installing with Model CAPXS – Smart Video Intercom S
Provides a clean aesthetic installation helping hide remnants of a previous installation.

E14400M

Cable Tie KSPEC 40 LB Black 14" Nylon 1000/pkg

Length: 14" Width: 3.6MM (0.140")
Low insertion and pull through force
Advanced pawl and teeth design
Angled tail provides quicker initial insertion alignment
Tail finger grips allow easier handling and tightening
Rounded edges provide added safety and eliminate insulation damage

.......more details

GHW-383-1HP-RH

Doorlec Industrial Gear Head Door Operator 1 HP 208V 3P with ECB and Nema4 modification

Extra heavy-duty industrial-type electric door operator for damp environments.
Worm gear reducer 40:1 ratio
#50 roller chain and sprockets from operator shaft to door shaft. (#60 chain optional)
Door speed: 7 inches per second (approx.)
Adjustable torque limiter (also called friction clutch)
Rotary type limit switches

.......more details

50018

Doorlec Photo Switch Polarized Explosion Proof Reflective w/Round Reflector

Class 1 Div 1 Groupes CDEFG explosion proof Certified CSA

31373-114

Doorlec Sprocket 60B36 1-1/4" Bore

MD00128

Micanan #410 Roller Chain 27 Pitch c/w Connecting Link

K004-KEY

Replacement Key for 3BXLT Key #4

Replacement key only for key #K004

K002-KEY

Replacement Key for 3BXLT Key #2

Replacement key only for key #K002

15-50B50QGH

Sprocket Kit 50B50 1.25" Bore x 1/4" Key w/ SS

GHW-353-3HP-RH

Doorlec Ind. Duty Jackshaft Carwash Op. 3 HP 575V 3P Right Hand *** By Quote Only

With DC2000 logic board
Worm-Gear Jackshaft type Industrial operator NEMA 4/12

CEDO-SPEC-ORDER

Cedo Special Order ** non-stocking items

specify size color details when ordering
Please call for pricing

MG00020

Micanan Flat Washer 1-1/16" ID x 1-3/4" OD

MQ00002

Micanan Cotter Pin 1/8" x 2.5" Long

K001A6407-1

LiftMaster Logic Board Absolute Encoder

Compatible with LiftMaster® Models RSW12V and RSW12VH Swing Gate Operators

50111

LiftMaster Center Support Bracket ATS211X-14 Sold per Unit

For 14 Feet ATS211X CD1014 Rail

GALV-295-258-R

Cut-to-Length Torsion Spring .295 x 2-5/8" Right Hand Wound Galvanized Blue Price per Inch

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

GALV-295-258-L

Cut-to-Length Torsion Spring .295 x 2-5/8" Left Hand Wound Galvanized Blue Price per Inch

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

TDC1222-14

Liftmaster Comm. 14FT Trolley Angle set (10-5814-P x 2) and #41 chain pack (TDC41-14) ***Actual length 203"***

Double Angle Rails for doors up to 14'6" high
Includes #41 chain pack

TDC1222-16

Liftmaster Comm. 16FT Trolley Angle set (10-5816-P x 2) and #41 chain pack (TDC41-16) ***Actual length 227"***

Double Angle Rails for doors up to 16'6" high
Includes #41 chain pack

TDC7-16

Liftmaster Comm. 16FT Trolley Angle set (10-5816-P x 2) and #48 chain pack (TDC48-16) ***Actual length 227"***

Double Angle Rails for doors up to 16'6" high
Includes #48 chain pack

TDC7-12

Liftmaster Comm. 12FT Trolley Angle set (10-5812-P x 2) and #48 chain pack (TDC48-12) ***Actual length 179"***

Double Angle Rails for doors up to 12'6" high
Includes #48 chain pack

TDC7-14

Liftmaster Comm. 14FT Trolley Angle set (10-5814-P x 2) and #48 chain pack (TDC48-14) ***Actual length 203"***

Double Angle Rails for doors up to 14'6" high
Includes #48 chain pack

TDC7-10

Liftmaster Comm. 10FT Trolley Angle set (10-5810-P x 2) and #48 chain pack (TDC48-10) ***Actual length 155"***

Double Angle Rails for doors up to 10'6" high
Includes #48 chain pack

TDC7-8

Liftmaster Comm. 8FT Trolley Angle set (10-5808-P x 2) and #48 chain pack (TDC48-08) ***Actual length 131*

Double Angle Rails for doors up to 8'6" high
Includes #48 chain pack

HW0777

Low Headroom Quick Close Device 3" track Sold as a Pair

Includes 1 RH & 1 LH bracket
Heavy Duty for doors up to 16' x 16'

041-0347-000

LiftMaster Camera Replacement Kit

Compatible with models featuring a yellow learn button and Secure View™ Video Camera; manufactured after 2021 only.

5M-NICE-BAR-ASBY

NICE Replacement Bar Assembly for M5BAR Barrier Gate

Bar assembly comes with:
XBA5
XBA13 -- RUBBER IMPACT PROTECTION STRIP
WA10 -- RED ADHESIVE REFLECTIVE STRIPS
SPGAP06400A – NYLON INSERT KIT
PD1614B0000

.......more details

OGH-6534-M-N1-LH

Manaras 1 HP 600V 3Ph Gear Head Operator Monitored ECB w/N1 Eyes Left Hand

A heavy-duty worm gear industrial operator designed for use on industrial standard high and vertical lift sectional doors or rolling doors and grills.
Includes a self-engaging chain hoist for manual operation
25 cycles per hour 80 cycles a day
Hoist on right side standard can easily be moved to the left in field
Full overload protection
BRACKET112 must be used for wall mounting

.......more details

GALV-331-334-144-L

Torsion Spring .331 x 3-3/4" x 12ft LH Galvanized Red/White

Wire size: .331
Inside diameter: 3-3/4"
Length: 12 ft
Galvanized

GALV-331-258-144-R

Torsion Spring .331 x 2-5/8" x 12ft RH Galvanized Red/White

Wire size: .331
Inside diameter: 2-5/8"
Length: 12 ft
Galvanized

GALV-312-258-144-L

Torsion Spring .312 x 2-5/8" x 12ft LH Galvanized Yellow

Wire size: .312
Inside diameter: 2-5/8"
Length: 12 ft
Galvanized

GALV-306-258-144-L

Torsion Spring .306 x 2-5/8" x 12ft LH Galvanized Red

Wire size: .306
Inside diameter: 2-5/8"
Length: 12 ft
Galvanized Stenciled

GALV-306-258-144-R

Torsion Spring .306 x 2-5/8" x 12ft RH Galvanized Red

Wire size: .306
Inside diameter: 2-5/8"
Length: 12 ft
Galvanized Stenciled

GALV-283-258-144-R

Torsion Spring .283 x 2-5/8" x 12ft RH Galvanized White

Wire size: .283
Inside diameter: 2-5/8"
Length: 12 ft
Galvanized Stenciled

GALV-250-334-144-L

Torsion Spring .250 x 3-3/4" x 12ft LH Galvanized Green

Wire size: .250
Inside diameter: 3-3/4"
Length: 12 ft
Galvanized Stenciled

GALV-243-334-144-L

Torsion Spring .243 x 3-3/4" x 12ft LH Galvanized White/Yellow

Wire size: .243
Inside diameter: 3-3/4"
Length: 12 ft
Galvanized Stenciled

GALV-225-2-144-LH

Torsion Spring .225 x 2" x 12ft LH Galvanized Orange/Green

Wire size: .225
Inside diameter: 2"
Length: 12 ft
Galvanized

PUSH185

Manaras Contact Block NC XB5

50695

Doorlec Clutch & Pulley Assembly for EHJX

Includes shaft and bearings

BEA-10LIGHT-TBASE

BEA Modular LED Signal Base

To be used with the BEA-10LIGHT modules.

User Guide Datasheet

BEA-10LIGHTBKT-TL

BEA Modular LED Signal Light Bracket

Bracket only for modular LED lights.

BEA-10LIGHT-TG

BEA Modular LED Signal Light Segment Green

Signal lights for industrial and vehicle flow management applications.
LED signal modular lights offer customizable configurations with “build-your-own” lighting elements that share a common base and bracket.
These LED signal units are available in red green yellow and an audible alarm cap and can be stacked in a tower configuration with up to six modules.
Operating temperature: -40 to 122F
Nema 4/IP65
Base sold separately

.......more details

User Guide Datasheet

15-50B16LGH

Sprocket 16 Teeth 1" Bore 1/4" Keyway w/SS

2100-529

Linear Woodruff Key #15 1/4 x 1"

2100-1622

Linear Jam Nut 1"-14W 5/16 Tap Hole

ME120-Y-4E-P/FT

Miller Edge Sensing Edge Yellow 4-Wire Monitored End Outlet Sold per Foot

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

T120

Manaras Trolley Track 20ft for 3/4HP & ALL APT models up-charge

For models MGT/OTH/OTBH/RTBH 3/4 hp only with Chain #41

GH-353-3

Doorlec Industrial Gearhead Door Operator 3HP 575V 3-Phase

Extra Deavy-Duty Gearhead Industrial Operator or large Sectional or Rolling Steel Doors
DC-2000 Logic Board with adjustable Timer To Close Delay On Reverse and Traffic Light Control
Worm gear reducer 40:1 ratio for high-torque and long life
Solenoid Disk Brake Prevents coasting and secures the door when closed
TEFC (sealed) continuous-duty electric motor with overload protection
Optional Friction Clutch available

.......more details

MT21-YELLOW-LH

Miller Edge 2-Wire Pressure Sensitive Edge Yellow Left Hand Outlet Sold per Foot

��Electromechanical medium profile edge for rolling fire door applications. •Touch sensitive signaling allows for immediate reversing or stopping of motion. •The MT21 is completely felixible and will contour to curved surfaces. The MT21 will also act as weatherstrip. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

29120

Doorlec Transformer 120V pr 28 V. sec. 50VA

120V primary 28 V secondary 50VA

GEAR001

Manaras Bevel Gear GH/MGH 5/8" 20 Tooth

HAE00052

Linear Main Cover LDCO

Replacement cover only

K20-3100M-5-H25

LiftMaster Electric Motor 1 HP 575V 3P L5

For use with various LiftMaster® Logic 5.0 Commercial Door Operators and Slide Gate Operators.
Also known as: 20-3100M-5 K20-3100M-5

MOD021AA

Manaras Safepack 24V Control Circuit

This is an option when purchased with an operator

CCTD-04

Fuse 600VAC/300VDC Class CC Time Delay 4AMP Sold per Fuse

Sold per fuse

MT21-2M-YELLOW-R

Miller Edge 2-Wire Monitored Pressure Sensitive Edge Yellow Right Hand Outlet Sold per Foot

��Electromechanical medium profile edge for rolling fire door applications. •Touch sensitive signaling allows for immediate reversing or stopping of motion. •The MT21 is completely felixible and will contour to curved surfaces. The MT21 will also act as weatherstrip. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

SPR410B12X1

Sprocket 410B12 x K1/4 2S 5/16-18 PH1/4

SD103L5-LH

LiftMaster Heavy-Duty Slide Door Operator 1 HP 208/230/460 3PH Left Hand (Must include hardware box)

Perfect for split and sliding doors involved with industrial applications.
It is installed above the door and corresponds with the direction the door will be traveling.
Comes equipped with an emergency disconnect and for manual lifting in an emergency and automatic reconnect.
The new logic 5 commercial operators come with MyQ Technology built in. * 828LM required
Built In Security+ 2.0 radio receiver
Solenoid brake included

.......more details

K94-37849-1

LiftMaster Electric Motor 1HP 3-phase

Replacement motor for SL595103U and SL595103UL

14-1008

PVC Roll 12" x .120" Standard Smooth 200' for Replacement Strip Curtain

Suitable for most average applications.
Temperature Range: -20°F to 150°F (-28° C to 66° C).
Formulated with ingredients that meet USDA requirements for incidental food contact.

CP-ENGAGE-SLIDE

Lynx Engaging Slide CDJ/MDJ

GALV-312-334-L

Cut-to-Length Torsion Spring .312 x 3-3/4" Left Hand Wound Galvanized Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED
Galvanized

PRO-EHJ-7583U-RH

Micanan 3/4 HP 208V 3PH Cont. Duty Jackshaft N1 Eyes Monitored ECB Right Hand

Comm / Ind Continuous Duty Belt Drive with Emergency Chain Hoist
24V class 2 control circuit with 40VA transformer to protect against short circuit
On board receiver with antenna
External radio control terminal strip
Low friction powder metal limit cam nuts with fully adjustable rotary type limit switch assembly •Three button open-close-stop control station Nema-1
Continuous duty industrial motor with overload protection

.......more details

Installation Manual Specification Sheet

GALV-225-258-L

Cut-to-Length Torsion Spring .225 x 2-5/8" LHW Galvanized Orange/Green Price per Inch

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

GALV-225-258-144-L

Torsion Spring .225 x 2-5/8" x 12ft LH Galvanized Orange/Green

Wire size: .225
Inside diameter: 2-5/8"
Length: 12 ft
Galvanized

GALV-273-258-144-R

Torsion Spring .273 x 2-5/8" x 12ft RH Galvanized Orange/Red

Wire size: .273
Inside diameter: 2-5/8"
Length: 12 ft
Galvanized Stenciled

GALV-262-2-144-L

Torsion Spring .262 x 2" x 12ft LH Galvanized Red/Yellow

Wire size: .262
Inside diameter: 2"
Length: 12 ft
Galvanized Stenciled

GALV-262-2-144-R

Torsion Spring .262 x 2" x 12ft RH Galvanized Red/Yellow

Wire size: .262
Inside diameter: 2"
Length: 12 ft
Galvanized Stenciled

GALV-243-2-144-R

Torsion Spring .243 x 2" x 12ft RH Galvanized White/Yellow

Wire size: .243
Inside diameter: 2"
Length: 12 ft
Galvanized Stenciled

GALV-218-2-144-R

Torsion Spring .218 x 2" x 12ft RH Galvanized Yellow/Orange

Wire size: .218
Inside diameter: 2"
Length: 12 ft
Galvanized Stenciled

GALV-207-2-144-R

Torsion Spring .207 x 2" x 12ft RH Galvanized Brown

Wire size: .207
Inside diameter: 2"
Length: 12 ft
Galvanized Stenciled

GALV-262-258-L

Cut-to-Length Torsion Spring .262 x 2-5/8" Left Hand Wound Galvanized Red/Yellow Price per Inch

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

DC-ADAPT125-100

Dyna-Hoist DC Series Adaptor 1-1/4" to 1"

SEF2420

Erone Adjustable Infrared Photocell 20M (65ft)

Adjustable lens 180° right to left and 40° Top-Bottom
Range 20M (66ft) in all conditions
Adjustable Sensitivity
Power supply 12/24 Vac/dc
Operating temperature -20/+55 °C
Dimension: 90 x 60 x 60mm (3.5 x 2.4 x 2.4 inches)

.......more details

Wireless System Chart

K20-8100M-DC

LiftMaster Motor 1HP 90VDC 1PH

K20-8100M-DC is a 1HP Motor Replacement Kit (90VDC BM CF). For use with various LiftMaster® 1HP 1-Phase Commercial Door Operators and Gate Operator Systems

K29-PB125

LiftMaster Reversing Motor Controller 115V KBPB-1

MA033

LiftMaster Hardware Kit Only for Articulating Arm ** Arm Not Included

Hardware kit for articulating arm models MA024 and MA034
Articulating arm hardware kit
Arm sold separately

B680H

FAAC Barrier Gate System ** Price by Quote Only

TRACK004

Manaras 1 Piece Galv Track 2x2x14'6 ** 1 pc Only

2 pices are required to make 1 set of tracks
Does NOT include the chain

41D9018

LiftMaster Cover Only for 8155W 8164W 8165W

For use with various LiftMaster® WiFi Chain Drive Garage Door Openers

R6000

Shaft Collar 1" with 2 Set Screws

Set Screws: 5/16 x 18

BEA-10FALCON-EX30

BEA Falcon Motion Detector w/Exp Proof Housing 30ft Cable

FALCON EX combines a microwave activation sensor with an explosion-proof/flame-proof housing
Ideal for use in unique environments such as chemical manufacturing petroleum refining and agriculture.
FALCON EX can be mounted from 11.5' to 23' to fit any industrial application.
Nema4/IP66
Detection Zone: Falcon EX: 13’×16’ at 16’
Operating temperature: -22 to 140F

.......more details

OHJ-6113-M-N1-RH

Manaras Heavy-Duty Jackshaft Operator 3/4 HP 120V 1 Ph Monitored ECB w/N1 Photoeyes RH

25 cycles per hour 100 cycles per day
An Industrial duty operator featuring both the patented Hoist-a-Matic a self-engaging chain hoist for manual operation as well as a floor level disconnect
Specifically designed to motorize grills when a manual egress is required
Mechanical brake
Hoist on right standard
Full overload protection

.......more details


User Name:
Password:
Remember Me:

	Forgot your password
Request a Login