Devanco Canada - Get The Right Garage Door Opener‎ and Parts

41A7278

LiftMaster Sprocket Kit 12-Tooth

Includes sprocket and screws

10-10191-GR

LiftMaster Brake Disc

For various Liftmaster commercial slide door operators
Also known as: 10-10191-GR 10-10191-GR 1010191 G105209 10-10191 105209

111396.0004

Overhead Brake Kit Model H 1/2HP 1PH

Installation instructions

MGH-6435-ECB-RH

Manaras 1.5 HP 480V 3P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

BEARING006

Manaras Flange Sealed Bearing 5/8"

Flange sealed bearing for 5/8" shaft

P-75

End Plug for 3/4" ID Rubber Hose

Sold per plug

MX00128

Micanan Clutch Assembly for PRO-GOHD

SF175-S

Spring Fitting 1-3/4" Stationary Side Only 1" shaft

MT22-GRAY-RH

Miller Edge 2-Wire Pressure Sensitive Edge Sold per Foot Gray

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

CP-BRK-WALL

Lynx Wall Bracket Commercial Operators

CP-CLUTCH-D-58

Lynx Clutch Disk 5/8"

K72-12789

LiftMaster Hand Chain Shaft Kit GH (1/2 - 2HP)

Complete with: Bevel Gear 3/4" ID Hand Chain Guice Hand Chain Shaft Bearing 3/4" ID Nyliner Bearing Compression Spring Chain Wheel Washers Roll Pins and E-Rings

PRO-HHD-10053E-R

Micanan 1 HP 575V 3P Heavy-Duty Jackshaft NM ECB No Eyes Right Hand

1 HP575V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Non-Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included
Emergency chain hoist with electrical cut-off for manual operation

.......more details

Installation Manual Specification Sheet

VPL-12

Autogate 12V Motor

H-0166

Autogate VBelt Banded B-59

New Style Double Reduction

41D8859

LiftMaster Cover 8550WL WLED

Burgundy Replacement Cover.
This one piece cover is compatible with various LiftMaster® Lock Capable Garage Door Openers Powered by myQ®; manufactured after 2017

CB31605000-KOR

Cable 3/16" 7x19 5000' Galvanized Supreme ** Price on request

Galvanized cable 3/16" 7x19 5000ft spool.
Cable break strength: 4200 lbs
A higher quality cable compared to the Chinese cable
Meets endurance test requirements of over 35000 work cycles
Lubricated for flexability and longer service life

Stainless Steel Cable Specifications

CGH751L5-LH

LiftMaster Gearhead w/ Brake & Carwash Mod. 3/4HP 115/230V 1P L5 - Left Hand

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting.
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

C-6X48-134-BLK

Thermal Window 6" x 48" for 1-3/4" Door Black

For 1-3/4" thick door

MOUNTSHAFT017

Manaras Clutch Shaft Kit for MTH MTBH (no pulley) Old Pre-1998

Input / clutch shaft kit for MTH MTBH
For old MTH MTBH with 1" diameter input shaft no pulley included

IRB-TX

EMX Industries Transmitter Board Only for IRB-4X *** NLA

AVP-1

Ace Type Keyswitch with Aluminum Mounting Plate

Zinc Alloy Die Casted housing and Cylindrical Chrome Plated
Tubular key with 2 keys
60 Combinations Available
Spring Return Type
Recommended for multiple dwellings
Contact ratings: 4 A 125V AC 2A 250V AC

.......more details

93D341

LiftMaster Cover Only Silver for EL25

Also known as 041D0341 41D341
Replacement cover for EL25

.363-6-R-C

Cut-to-Length Torsion Spring .362 x 6" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

.363-514-R-C

Cut-to-Length Torsion Spring .362 x 5-1/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold separately
For factory installed cones use part no. C-514-INSTALLED

.331-258-L-C

Cut-to-Length Torsion Spring .331 x 2-5/8" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.319-514-R-C

Cut-to-Length Torsion Spring .319 x 5-1/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-514-Installed

.319-258-R-C

Cut-to-Length Torsion Spring .319 x 2-5/8" Right Hand Wound Coated ** Price by Quote Only

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-258-Installed

.312-514-L-C

Cut-to-Length Torsion Spring .312 x 5-1/4" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.295-334-L-C

Cut-to-Length Torsion Spring .295 x 3-3/4" Left Hand Wound Coated ** Price by Quote Only

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

.295-2-L-C

Cut-to-Length Torsion Spring .295 x 2" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.273-2-R-C

Cut-to-Length Torsion Spring .273 x 2" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.218-258-L-C

Cut-to-Length Torsion Spring .218 x 2-5/8" Left Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.207-134-R-C

Cut-to-Length Torsion Spring .207 x 1-3/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

MAG-1

Magnetic Tool Box 3.5" x 3.5" x 5.25"

100lb. magnet which allows it to be easily stuck and removed from a metal surface.
Ideal for use on forklift

PRO-GH-5053U-L

Micanan 1/2HP 575V 3P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-GH-5021U-R

Micanan 1/2HP 230V 1P Gearhead Operator N1 Eyes Monitored ECB Right Hand (PRO GHE)

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-HB-7581U-LH

Micanan 3/4HP 208V 1P Hoist Op. with Brake N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

PRO-HB-5083U-RH

Micanan 1/2HP 208V 3P Hoist Op. with Brake N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included
On-Board receiver holds up to 20 transmitters

PRO-HB-5081U-RH

Micanan 1/2HP 208V 1P Hoist Op. with Brake N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included
On-Board receiver holds up to 20 transmitters

PRO-HB-5021U-LH

Micanan 1/2HP 230V 1P Hoist Op. with Brake N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included
On-Board receiver holds up to 20 transmitters

CLIP020

Manaras Pocketwheel Roller Clip

PRO-H-5053-E-LH

Micanan 1/2HP 575V 3P Hoist Operator NM ECB No Eyes Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Solenoid brake OPTIONAL
Non-monitored board NO photoeyes

PRO-H-5023-U-LH

Micanan 1/2HP 230V 3P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

PRO-H-5021-U-LH

Micanan 1/2HP 230V 1P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

PRO-H-5081-U-RH

Micanan 1/2HP 208V 1P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

PRO-J-10023-U-LH

Micanan 1HP 230V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

MG-00082

Micanan Plastic Spacer for Boards (Long Length 1.190)

MM-00360

Micanan Circuit Board Support U-Bracket

MK-00679

Micanan Plastic Shoulder for Antenna Connector

MK-00137

Micanan Transformer 600V-24V-100VA

MV-00272

Micanan Key Switch O/C Single Gang Nema 1 Flush Mount

MV-00011

Micanan 3-btn O/C/S w/Key Lock-Out Nema-4 Pushbutton Control Station

Surface mount

PRO-H-5083U-RH

Micanan 1/2HP 208V 3P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

50740

Doorlec On/Off Switch 575V 3Ph Gate Op

20amp

PRO-J-10021-U-RH

Micanan 1HP 230V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-10081-U-RH

Micanan 1HP 208V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

.421-514-R

Cut-to-Length Torsion Spring .421 x 5-1/4" Right Hand Wound Gold

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-514-INSTALLED

.437-514-R

Cut-to-Length Torsion Spring .437 x 5-1/4" Right Hand Wound Red/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.406-514-L

Cut-to-Length Torsion Spring .406 x 5-1/4" Left Hand Wound Blue/Yellow

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-514-INSTALLED

.363-514-R

Cut-to-Length Torsion Spring .362 x 5-1/4" Right Hand Wound Green/White

Priced per inch - cones sold separately
For factory installed cones use part no. C-514-INSTALLED

.343-258-L

Cut-to-Length Torsion Spring .343 x 2-5/8" Left Hand Wound Blue/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.306-514-L

Cut-to-Length Torsion Spring .306 x 5-1/4" Left Hand Wound Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.306-514-R

Cut-to-Length Torsion Spring .306 x 5-1/4" Right Hand Wound Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.306-2-L

Cut-to-Length Torsion Spring .306 x 2" Left Hand Wound Red

Priced per inch
For factory installed cones priced seperately - use part no. C-200-INSTALLED

.295-6-R

Cut-to-Length Torsion Spring .295 x 6" Right Hand Wound Blue

Priced per inch
For factory installed cones priced seperately - use part no. C-600-INSTALLED

BCH755L5-RH

LiftMaster Hoist Op. with Carwash Mod. 3/4 HP 575 VAC 3 Ph L5 Right Hand ***Replaced by CRBH755L5-RH

Industrial Duty Hoist Operator with Damp Environment modification
Comes with CPS-UN4 photoeyes
External brake included

PRO-LJ-5021-U-RH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Right Hand

On-Board receiver holds up to 20 transmitters

PRO-LJ-5011-U-LH

Micanan 1/2HP 115V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

PRO-GT-10083-U

Micanan 1HP 208V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

.273-258-L

Cut-to-Length Torsion Spring .273 x 2-5/8" Left Hand Wound Orange/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

PRO-APTB-5081-U

Micanan 1/2HP 208V 1P Apartment Trolley Operator With Brake N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-APT-7581-U

Micanan 3/4HP 208V 1P Apartment Trolley Operator N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board

PRO-TB-10053-U

Micanan 1 HP 575V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-10043-U

Micanan 1 HP 460V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-5083-U

Micanan 1/2HP 208V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-5025-U

Micanan 1/2HP 220V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-5081-U

Micanan 1/2HP 208V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

60-7242

Econo Caution Sign English 14" x 10"

1004-134-16'

Aluminum Bottom Retainer 1 3/4" U-Shape with Reinforcement 16 ft***Actual Length 16'2"****

For door thickness 1-3/4"

PRO-GH-20053-PNL

Micanan 2 HP 575V 3P Gearhead Operator NO CONTROLS *** Price on Request

Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation
Universal Right or Left Hand mount

Installation manual Specification sheet

SPUR_GEAR

Spur Gear For Holdown Assembly

RATCHET_BAR

Ratchet Bar for Holdown Assembly 8-8786 ** Quote Only

E/1929/031

Automatic Systems Installation Plate Ass'y BL229

Used on the BL229 gate op.

BB

Molded Rubber Bumper Black 24" L x 10" W 4" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles molded bumpers will not warp rust rot or harden.
Bumper comes with 2 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts
24" L x 10" W 4" Projection

.......more details

B

Molded Rubber Bumper Black 24" L x 12" W 3" Projection 4-Hole 2 Reflectors Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 6 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

LB1212-14

Laminated Bumper Standard Black 12" L x 14" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1212-12

Laminated Bumper Standard Black 12" L x 12" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB924-11

Laminated Bumper Black 9" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB912-12

Laminated Bumper Standard Black 12" x 12" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB812-12

Laminated Bumper Standard Black 12" x 12" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-36SF

Steel Faced Laminated Bumper Black 10" x 36" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB406-24SF

Steel Faced Laminated Bumper Black 6" x 24" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

Q080

LiftMaster Dolly Latch Kit K75-50138

For Liftmaster trolley operator HCT

LB412-24SF

Steel Faced Laminated Bumper Black 12" x 24" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB410-36SF

Steel Faced Laminated Bumper Black 10" x 36" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB410-18SF

Steel Faced Laminated Bumper Black 10" x 18" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB612-36SF

Steel Faced Laminated Bumper Black 12" x 36" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB612-24SF

Steel Faced Laminated Bumper Black 12" x 24" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LLB620-22SF

Steel Faced Laminated Bumper Black 6" Projection L-Shaped 20" x 22" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.

.......more details


User Name:
Password:
Remember Me:

	Forgot your password
Request a Login