Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MB-03004

Micanan Electric Motor Only 1 HP 110/220V 1PH C-Flange TEFC 56C

C-Flange TEFC electric motor
Fits models: GT GH GHC & GSD

GH-3-LH

Doorlec Industrial Jackshaft Door Operator 3 HP 575V 3P TEFC Motor Left Hand

Custom-designed extra heavy-duty industrial-type electric door operator
Worm gear reducer 40:1 ratio
#60 roller chain and sprockets from operator shaft to door shaft.
Door speed: 7 inches per second (approx.)
Adjustable torque limiter
Rotary type limit switches

.......more details

AW12K500-18

Miller Edge Air Wave Kit 18ft No Coil Cord

Kit Includes: AW12 Air Wave Switch Barbed Coupler (18') RAH-500 1/2" dia. Rubber Hose Wire Nuts End Plugs

MB-03102

Micanan Electric Motor Only 1 HP 230/460V 3PH Base Mount O.D.P FR56 (MB33201)

Base mount motor fits: T TB APT J EJ H EHJ HHD SD
Same as MB-03102 MB33201 MB-33201

MGJ-5011U-LH

LiftMaster Medium-Duty Logic Gear-Reduced Op. 1/2 HP 115V 1Ph Left Hand

MGJ is designed for use on rolling grilles and shutters.
Maximum recommended duty cycle: 12 cycles per hour.
Heavy-duty wormgear-in-oil-bath speed reducer
3-button station for open/close/stop functionality
315 MHz radio receiver is integral to the Medium-Duty Logic board
UL325-2010 Monitored Entrapment Capability (provides primary monitored entrapment protection through monitored photo sensors: either CPS-U or CPS-UN4 or a 4-wire monitored edge using the CPS-EI interface)

.......more details

Installation manual Sell sheet

K20-1075B2LPH24

LiftMaster Electric Motor 3/4 HP 115V/208V/230V 1Ph Logic 5

Standard base mount 3/4 hp motor for new L5 operators
Also known as: 20-1075B-2LP K20-1075B-2P-H24 K20-1075B-2LP

PPLK1PH-10

LiftMaster Passport Lite 1-Button Mini Proximity Remote with Sec+ 2.0 Technology 10/PKG

Passport Lite Remote Controls provide cost-effective single button access solutions for gate access only or high-capacity commercial properties applications such as employee parking lots and tenant garages.
These remote controls are specifically designed for gate access control and are not compatible with LiftMaster Garage Door Openers.
2x the range of standard remote controls
Narrow-band transmission on 3 simultaneous frequencies (310 MHz 315 MHz 390 MHz)
Compatible with LiftMaster® commercial receivers (850LM 860LM PPWR STAR1000) and Security+ 2.0™ Gate Operators
Keychain remote control sold in a 10 pack

.......more details

Programming instructions Instructions de programmation Sell sheet Brochure

MK00708

Micanan Varistor Harness 230V with Blue Wires

WINDOW-SP.ORDR

Special Order Window

Made to customers specific requirements

SSZP16-6-114

Solid Shaft 1-1/4" Keyed Zinc Plated 16'-6"

PRO-GH-10083U-R

Micanan 1 HP 208V 3P Gearhead Op. N1 Eyes Monitored ECB Right Hand

Designed for use on all rolling doors and grilles and for large sectional doors with high or vertical lift.
Full function smart 10.0 logic board featuring on-board receiver with antenna and enhanced program selections.
External radio control terminal strip
Three button O/C/S control station Nema-1
Supplied with Nema-1 photocells
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

MP00088

Micanan Track and #41 Chain for 8' h Door *Actual length 126"*

For 3/4 & 1 HP Micanan trolley operators

PRO-TB-10083-U

Micanan 1 HP 208V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

02-103-FR

Push Button Station 3-btn Surface Mount French Nema 1 Metal Housing

PBS-3S
Ouvre-Ferme-Arret
Momentary contact
Metal enclosure
Nema 1
Dimensions: 5-5/16" H x 2-3/8" W x 1-13/16" D

.......more details

9150000630

1/4" Stops ONLY 100/pkg

Stops only - 100 per pack

WHITING-PANEL

Whiting Special Order Replacement Panel Only Price by Quote Only

Special order to customer's specs

SL14COP-50

Copper Sleeve 1/4" 50 Sleeves per Pkg *price on request

Oval sleeves ONLY
Stops sold separately part # ST14COP

26253

Doorlec Shaft 9-3/4" x 5/8" Keyed LJ / LJH

MK-00430

Micanan Capacitor 240V/250V 70 Mf

For limited duty 110V operators

MT22-MON-Y-LH

Miller Edge 4-Wire Monitored Pressure Sensitive Edge Yellow Sold per Foot

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

.262-334-R

Cut-to-Length Torsion Spring .262 x 3-3/4" Right Hand Wound Red/Yellow

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

PRO-HHD-7553U-R

Micanan 3/4HP 575V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand

3/4 HP575V 3PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

Installation manual Specification sheet

PRO-TB-7511-E

Micanan 3/4HP 115V 1P Trolley Operator with Brake NM ECB No Eyes

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Non-Monitored board NO photoeyes

19054

Doorlec VBelt 5L380

works on model SWGO

28-30080

Truck Door 1" Horizontal Track 6" Radius for T-Style Std Doors 120" Curbside (RH)

Galvanized steel 14 gauge construction
For use with 1" diameter rollers
6" radius for smooth door operation
Track coupler used for proper alignment at track joints

MI00001

Micanan Motor Pulley 5L 5/8" ID x 2" OD

1005-2-14

Aluminum Bottom Retainer U-Shaped 14' Long**Actual Length 14'2"***

For door thickness 2"

E3JM-30FT

Omron Thru-Beam Photoelectric Sensor Nema 4 0-30ft Range

Easy-to-wire terminal block
Built-in timer offers selectable ON-delay OFF-delay and one-shot
Relay or transistor output models
Light-ON/Dark-ON operation switch selectable
Model: E3JM-10M4-US

MGH-6115-ECB-RH

Manaras 1.5 HP 120V 1P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

Installation manual Sell sheet

10-1000-CUSTOM

Strip Curtain PVC Door Custom Made ** Price by Quote Only

SF600U-114

Spring Fitting 6" Pair for 1-1/4" Shaft

Universal thread and is available for 1" or 1.25" Bore - must specify when ordering.
Pair includes: (1) winding & (1) stationary.
Not single thread.
Winding bar hole 5/8"

.312-334-R

Cut-to-Length Torsion Spring .312 x 3-3/4" Right Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

108D79

LiftMaster Light Lens 108D0079M

Replaces 108D68 and 108D68-1

CABLE_532SS5000

Cable 5/32" 7x19 5000' Stainless Steel ** Price on request

CHS401-114

Chain Hoist Shaft Mount 1-1/4" Shaft 4:1 JR Torque Force (126685)

Shaft Mounted Junior Hoist
4:1 Reduced Drive
Sprocket: 41B36. Bore size: 1-1/4" diameter
Cross Reference: OMI 4020
Requires minimum 3/8" center line offset.
Set includes: 26' of hand chain 22" of #41 roller chain Chain keeper (2) shaft collars 1/4" square key and a wall stabilizer bracket.

.......more details

Sell sheet

VBELT_4L290

VBelt 1/2" x 29" (4L290)

V-Belt not cogged

5001-14-BLACK

Residential Side & Top Weather-Strip 14' Long - Black

PVC wrapped
Painted aluminum retainer
Dual fin vinyl

.243-258-L

Cut-to-Length Torsion Spring .243 x 2-5/8" Left Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

200BL-10

2" Light Brush Insert 10ft Long

Polypropylene bristles
Same as MS1703-120

41A7920-2

LiftMaster Hardware Kit

SNACPH32

LiftMaster HID 30-bit Proximity Card Facility Code 2 *Discontinued*

Same as SN000099-30-2
Compatible with KPR2000 reader
Replaced by LMPC2-SN (need to know facility code)

MIRM-T2-50

Miller Edge Patriot 2 Photo Eye Monitored 50ft Non-Contact ** Discontinued

Attaches directly to a Sectional door.
The photo eyes travel below the door during the closing cycle.
Unlike traditional static mount photo eyes; Patriot travels with the door sensing obstructions prior to contact.
The Patriot2 non-contact system consists of thru beam photo optics.
Emitting and receiving eyes mount into a rigid steel spring loaded retracting housing.
The housings attach to the bottom section of the door and extend below the leading edge of the door providing an invisible infrared light beam of protection.

.......more details

SSZP15-6-114

Solid Shaft 1-1/4" Keyed 15'6" Zinc Plated

Actual length is approx. 15'-6"

346

Cable Clamps Galvanized 3/16" Sold per piece

Galvanized malleable cable clip

620-00993

Linear Heater Kit 230V

Heater kit for slide gate operator 230V

AOMRON

Omron Heavy-Duty Retro-Reflective Photo Eye 110VAC/24V 40ft Range

24-240 VAC/DC
35mA/125mA at 24VAC
20mA/60mA at 110VAC
UL listed to UL325 standards
NEMA 3 4 12 Outdoor Rating
40 ft. sensing distance

.......more details

C-514-INSTALLED

Cones 5-1/4" Factory Installed (Pair)

For do-it-yourself installation use part no. SF514U

41A5021-5I

LiftMaster Electronic Circuit Board Assembly 390MHz *** NLA

1 piece logic board with end panel
Used on 390Mhz Security+ AC belt drive operators made from 1997 to 2005.
Unit will have a red/orange learn button
Also know as 41A5021-D 41A5021-5E 41A5021-5F 41A5021-5G 41A5021-5H 041A5021-5I

7001-7-CHARCOAL

Commercial Side & Top Weather-Strip 7' Long - Charcoal 7001-HH (H)

Charcoal galvanized steel with charcoal dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

PBTL-3-102

Key ONLY for PBTL-3 Z102 Sold per Key

Cut Key # Z102
Price for 1 key

SNS1P6

Belden RG6 Co-axial "F" Male connector Snap-N-Seal

5001-10-BLACK

Residential Side & Top Weather-Strip 10' Long - Black

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

1104-16'-LT-BNZ

Residential Side & Top PVC Weather-Strip with cap 16' Long - Light Bronze (F) **NLA

Light bronze rigid vinyl retainer with light bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

07-8058

LiftMaster Crank Link BG790

41D8181

LiftMaster Cover

5001-WG-9-MOAK

Residential Side & Top Weather-Strip 9' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Sold by full case quantity (20)

5001-WG-8-MOAK

Residential Side & Top Weather-Strip 8' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Sold by full case quantity (20)

28-03090

Truck Door 1" Vert. Track and Right Angle Assbly Curbside (RH) 96.5" Todco Style**To extent of inventory

For Todco style doors
Galvanized steel 14-gauge construction
Includes right angle frame 1" track and operator bracket
Fits doors 72" - 90" high

28-00190

Truck Door 1" Std Vert. Track and Angle Assbly Curbside (RH) 96.5" Todco Style

Fits Todco style doors
Galvanized steel 14-gauge construction
Includes J-style channel mounting angle with track and operator bracket
For door opening less than 90" high
Fits door sizes 72 - 90" high
Cross ref: T #49014-1 T #41034-1 & W #4046

.......more details

SF514U-114

Spring Fitting 5-1/4" Pair for 1-1/4" shaft

Universal thread for use in either LH or RH wound springs.
Pair includes: (1) winding 1-1/4"bore & (1) stationary 1" bore.

801-300-001-00

Equinoxe Long Range Receiver 1-Door 433 MHz Pre-2016 *** To Extent of Inventory

1000 ft range
Old generation - prior to 2016

Programming Instructions Instructions de programmation

ACT-34D

Linear 4-Channel Block Coded MegaCode Key Ring Trans Prox Transmitter 318 MHz

Compatible with all Linear access receivers and controllers
Built-in 26-bit Wiegand proximity tag
Eliminates need for separate proximity card or tags and transmitter
Supplied with quick-disconnect key ring
Same facility and ID codes for transmitter and proximity tag
Sold in lots of 10

.......more details

71-90TS

LiftMaster Timer Kit for TS Wiring

Field mod. kit

MOUNTSHAFT016A

Manaras Clutch & Hoist Shaft Kit for Opera-SH Nema 4/12 (OSHW)

Input / clutch shaft kit for Manaras Opera-SH N4/12

K001A3200-2

LiftMaster Gate Receiver Isolation Kit

Isolates the 850LM receiver from the ground loop and prevent the fuse from blowing.

MB-02002

Micanan Electric Motor Only 3/4HP 110/220V 1PH TEFC

Base mount motor fits: TW TBW JW HW HHDW SDW

KH-3.5

Magnetic Key Hole 3-1/2" Tall

Decorative key hole only
Black flexible magnetic material with deep embossed design

H12G12-SS

Hinge #12 x 12 gauge Stainless Steel

Manufactured with 12ga. Rust-Resistant Stainless Steel
Universal Design
Fits Most Overhead Sectional Doors
Priced Per Each

ME123-M-YEL-U

Miller Edge Yellow Universal 4-Wire Monitored 2" wide x 1-1/2" high Sold by the Foot

Electromechanical slide in edge for sectional doors and sliding gates.
Touch sensitive singaling allows for immediate stopping and reversing of motion
Temperature range: -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Worksheet Installation manual Sell sheet

2B735

LiftMaster Main Board EL25 (041B0735)

Same as 041B0735

BK020/PR

Commercial 2" Safety Bottom Bracket Sold as a Pair (L & R) *** No Longer Available

Maximum cable diameter: 3/16"
Maximum door weight: 1300 lbs Zinc
Plated Steel
Sold as a pair

1003-4-DF-200FT

Bottom U-Rubber 4" Dual Fin Black 200' Long

200ft spool of vinyl insert.
Dual fin

.437-6-R

Cut-to-Length Torsion Spring .437 x 6" Right Hand Wound Red/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED

21-7115-1

LiftMaster Transformer 115/230V 1Ph

BRAKEPART016

Manaras Brake Pad Assembly MLT MLJ MLH

Includes: 1 x BUSHING026 1 X CLUTCHPLATE008 1 X PLATE041

11202

Doorlec Cap Screw 1/4"-20 x 4"

CABLE008

Manaras Disconnect Cable 25 ft

Cable 3/32"

PRO-HBH-7523U-L

Micanan 3/4HP 230V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand (Pro-HHD)

3/4 HP230V 3PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

8086.225.310

Whiting .225 x 2-5/8 IN x 31" Roadside with Cones

An original Whiting assembly

CP-BRG-58

Lynx Bearing 5/8"

6 in total on a MCJH

CP-BRG-1

Lynx Bearing 1" *** Replaced by HW-BRG-1

2 in total on a MCJH

20456R

Genie Pulley Support Kit *** No Longer Available

Front metal clip with pulley
Front idler for use with Genie and Overhead Door T-rail systems

RA-AD-WKP-05

Lynx 5-btn Wireless Keypad AD455 372 MHz

Programming Instructions Compatibility chart

MOUNTSHAFT010

Manaras Hoist Shaft Kit for MJH (pre-1998)

Drawing

OSH-6112-CONT-R

Manaras Opera-SH 1/2HP 120V 1Ph Contactor Right Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"

Installation Manual Sell Sheet

.250-258-L

Cut-to-Length Torsion Spring .250 x 2-5/8" Left Hand Wound Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

MGH-6113-ECB-RH

Manaras 3/4 HP 120V 1P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection