Devanco Canada - Get The Right Garage Door Opener‎ and Parts

31D380

LiftMaster Sprocket Cover

Sprocket Cover Replacement Kit for use with various LiftMaster® and Chamberlain® Chain Drive Garage Door Openers

HRB-7

High Riser Bracket for 7" Above Dock or Higher 7"

High Riser 7" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

MM00447

Micanan Idler Wheel PRO-APTC

LB1212-36

Laminated Bumper Standard Black 12" L x 36" W 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB810-14

Laminated Bumper Standard Black 10" x 14" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

Drawing

TVB420-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

Drawing

TB410-18SF

Steel Faced Laminated Bumper Black 10" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

STRUT-2-1/4-12'-NH

Door Strut 2-1/4" Non Hemmed 12 ft Long

Reinforcement bar 2-1/4"

LB412-14SF

Steel Faced Laminated Bumper Black 12" x 14" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB612-36SF

Steel Faced Laminated Bumper Black 12" x 36" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB612-24SF

Steel Faced Laminated Bumper Black 12" x 24" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB610-14SF

Steel Faced Laminated Bumper Black 10" x 14" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB624-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 24" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LB610-24SF

Steel Faced Laminated Bumper Black 10" x 24" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LLB620-22

Laminated Bumper Black 6" Projection L-Shaped 20" x 22" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.
This model has angles on both sides

.......more details

LB406-24

Laminated Bumper Standard Black 6" x 24" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

MK-00787

Micanan Heater Probe 120V 20W Brass Fitting Field Install

PRO-GHC-30053

Micanan 3 HP 575V 3P Gearhead Operator No Controls

Specification sheet

02-404

LiftMaster Key Switch Assembly On/Off Nema 4/12 **DISCONTINUED

Two Position Key Control Station
Outdoor Surface Mt. (NEMA 4/12)
Non-Tamperproof
OPEN/CLOSE spring return to center (OFF) key removable in center position only.
Should only be used on operators wired for constant pressure to open and close (all LiftMaster industrial operators with type D control wiring).
Die cast metal enclosure

.......more details

PRO-PL-INV-200-23

Micanan Wall Mounted Control Panel with Variable Frequency Drive Mod. 2HP 230V 3 PH

Additional charges apply for adding PBS on cover or if panel is not ordered with an operator

MB-03202

Micanan Electric Motor Only 1 HP 575V 3PH Base Mount O.D.P FR56

Fits T TB APT APTC J EJ H EHJ HHD SD

MP-00002-575V

Micanan Apartment Feature: Timer-to-Close Function and Light Control Modification only

Controlling action of two lights- sockets supplied on cover

MP-00002-230V

Micanan Apartment Feature: Timer-to-Close Function and Light Control Modification only

Controlling action of two lights- sockets supplied on cover

PRO-HHD-7581U-L

Micanan 3/4HP 208V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand

3/4 HP208V 1PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

Installation Manual (EN)Specification Sheet

26CW94523-CUT

Truck Door Intermediate Panel (13" x Cut-to-Size) Painted White for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white

4X12SC50

Devanco Loop 4' x 12' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection

Installation manual Manuel d'installation Loop placement guide Guide de positionnement des boucles

9006-10

Excalibur Threshold Kit 10'2" x 6" W Solid Aluminum ** Price by Quote Only

Stands 1/2" tall
Built with 6061-T6 solid aluminum to withstand extreme weight and excessive traffic conditions.
Two-way fastening/seal system won’t shift buckle or leak
Top V-groove design provides for skid proof protection and improved tire traction on loading docks and incline ramps.
The 1/2" diameter wire access port makes it easy for sensor and security installations.
The kit comes complete with pre-drilled counter sink holes 3/8" anchors and sealant.

.......more details

1104-7FT-GREEN

Residential Side & Top PVC Weather-Strip with cap 7' Long - Green (R)

Green rigid vinyl retainer with green flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

5001-14-WHITE

Residential Side & Top Weather-Strip 14' Long - White

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

.306-258-L

Cut-to-Length Torsion Spring .306 x 2-5/8" Left Hand Wound Red

Priced per inch
For factory installed cones priced seperately - use part no. C-258-INSTALLED

41A5483-2C

LiftMaster Circuit Board Assembly *** To extent of inventory

Assembly includes: Circuit board and end panel
For chain drive units with one light
Fits models 2245 & 2255
Last letter of the part # indicates revision date the most recent product will be sent out

BOLT016

Manaras Hex Bolt 1/4-20 x 4

7001-8-BRONZE

Commercial Side & Top Weather-Strip 8' Long - Bronze (BZ)

Bronze galvanized steel with bronze dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

26CW94322-CUT

Truck Door Bottom Panel with Seal (12" x Cut-To-Size) Painted White for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes only with bottom retainer and seal (installed)

.......more details

MD-00189

Micanan Roller Chain Waterproof #41 Sold by the Foot

221816

Decorative Hinge Assembly Carriage Style 16" Malleable Iron Sold per piece (175260)

As seen on carriage house doors
Total length is 18" for hinge and strap assemby.
1/4" thick
Mounting hardward sold separately
Sold per piece

GH-3-LH

Doorlec Industrial Jackshaft Door Operator 3 HP 575V 3P TEFC Motor Left Hand

Custom-designed extra heavy-duty industrial-type electric door operator
Worm gear reducer 40:1 ratio
#60 roller chain and sprockets from operator shaft to door shaft.
Door speed: 7 inches per second (approx.)
Adjustable torque limiter
Rotary type limit switches

.......more details

5001-9-DK-BROWN

Residential Side & Top Weather-Strip 9' Long Commercial Brown

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

26CW94625-CUT

Truck Door Top Panel w/o Hardware (15" x Cut-To-Size Painted White for Whiting Dryfreight

These panels are cut to customer's specifications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white

MS00005

Micanan Trolley Track 12-ga 14'-6" L Per Set ( Includes 2 Angles Only)

Track only- no chain or hardware

SBX-N1-P-5011JH

Micanan Control Box PRO-H

Dimensions: 11" x 8" x 5" h

TRACK-3"-RAW-16

Raw Vertical Track 3" 184" 13g Sold as a PAIR

MX00203

Micanan Complete Control Box Only for PRO-HHDU/TU Nema 1 110V

070032-0000

Overhead Double Drive Pulley

TRACK-2"-RAW-13

Raw Vertical Track 2" 13'-0" Sold per Piece

MP-00008

Micanan Two-Door Interlock Modification

Only allows one door to be opened at one time

PRO-GH-10083U-L

Micanan 1 HP 208V 3P Gearhead Op. N1 Eyes Monitored ECB Left Hand

Designed for use on all rolling doors and grilles and for large sectional doors with high or vertical lift.
Full function smart 10.0 logic board featuring on-board receiver with antenna and enhanced program selections.
External radio control terminal strip
Three button O/C/S control station Nema-1
Supplied with Nema-1 photocells
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

MU-00005

Micanan Hand Crank Handle 6' Long

For hand crank operation in lieu of hand chain and pocket wheel

MM00013

Micanan Chain Guard (MM00431)

Fits PRO-H/HB
New part number # MM00431

.312-6-L

Cut-to-Length Torsion Spring .312 x 6" Left Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED

1004-134-12'

Aluminum Bottom Retainer 1 3/4" U-Shape with Reinforcement 12 ft**Actual Length 12'2"***

For door thickness 1-3/4"

PRO-TB-5011-U

Micanan 1/2HP 115V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

K76-34740

LiftMaster Limit Passpoint Kit

Kit Includes: Learn Limit Switch Learn Limit Nut Limit Shaft Assembly Sprocket and Wire Harness
For RSL12V RSL12VH
Aslo called Learn Limit Assembly Kit

SL332-ZP-COPPER

Zinc Plated Copper Sleeve 3/32" 100 Sleeves per Pkg *price on request

Oval sleeves ONLY
Stops sold separately part # ST332COP. Stops are not zinc plated

D-2-6

Keyed Disconnect Device 6ft Cable

Operated from the outside to disconnect the trolley for manual operation of the door
Must specify if keyed alike is required or keyed random will be shipped
Mounting plate dimensions: 2 1/2” x 1 3/32”

.243-258-R

Cut-to-Length Torsion Spring .243 x 2-5/8" Right Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

21702

Doorlec Close Auxiliary Switch Double Limit DAT

OPH-6113-ECB-LH

Manaras Opera-H 3/4HP 120V 1Ph with Electronic Circuit Board Left Hand

A heavy-duty industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a self-engaging chain hoist for manual operation
Clearence: side room required 15"

Installation manual Sell sheet

K001C3196-3

LiftMaster Antenna 315MHz

Fits SL595

SNACPH39

LiftMaster HID 30-bit Proximity Card Facility Code 9 *Discontinued*

Same as SN000099-30-9
Compatible with KPR2000 reader
Replaced by LMPC2-SN (need to know facility code)

SOLID_SHAFT_13'

Solid Shaft 1" Keyed 13 ft Galvanized

Actual length is approx. 13'-1"

65-32449

LiftMaster Thermostat Control Heater 115V & 575V Fin Type ** Discontinued

Designed to automatically maintain a suitable temperature inside a control enclosure down to -40 degrees F.
Uses a high surface area aluminum heat emitter to eliminate the need for a fan
Provides low-radiation and high-convection heating in the enclosure
Adjustable from 30 degrees to 120 degrees F. (0 to 50 degrees C.) 208V - 460V
Compatible with operators SL575 SL585 and SL595

0-7530-444

FHP Electric Motor 1/3 HP 110V 1625 RPM Motor A099231

CB-1.097

Whiting Stainless Steel Cable 97" L with Plain Grommet 5/16" Eye

EHJ-383-3/4

Doorlec Industrial Jackshaft Op. 3/4 HP 208V-3Ph

Equipped with: 3-btn control Adjustable Automatic Friction Clutch Emergency Chain Hoist and Heavy-Duty Solenoid Brake.

SA-TORSION-ASSY

Complete Torsion Assembly Special Order

Special order

PRO-H-7511U-RH

Micanan 3/4HP 115V 1P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

Installation manual Specification sheet

E/BLOP/128

Double Channel Loop Detector- factory installed on logic

5001-WG-9-MOAK

Residential Side & Top Weather-Strip 9' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Sold by full case quantity (20)

1104-10FT-BRONZ

Residential Side & Top PVC Weather-Strip with cap 10' Long - Bronze (F)

Bronze rigid vinyl retainer with bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

1104-14FT-BRONZ

Residential Side & Top PVC Weather-Strip with cap 14' Long - Bronze (F)

Bronze rigid vinyl retainer with bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

3228.1

Whiting 2" Nylon Roller 3" Shaft Stainless Steel *** To Extent of Inventory

This is a Whiting original roller

28020024-500

Cable Stainless 3/8" 1x19 500' Inox ** Price on request

Not for use in aircraft applications
1x19 contruction type 302 / 304

Comparison charts

CHI-SPECIAL

C.H.I. Special Order Door

Special order as per customer's requirements

17-10363

LiftMaster Pulley 1-5/8" OD 1/2"B 4L Belt

BRACKET003

Manaras Disconnect Lever Bracket MJ

MGS20-Y-2U-04

Miller Edge Sensing Edge Square Yellow 2-Wire Universal Outlet 4ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

8086.225.310

Whiting .225 x 2-5/8 IN x 31" Roadside with Cones

An original Whiting assembly

ST-CLEAR-TUBE

Soft Touch Clear Tubing Sold per Foot

ST-ENDCAP

Soft Touch End Caps Sold Individually

27-8004-K

LiftMaster Aux. Contact Block Relay

2-NO/ 2-NC Contacts
Used on 03-8024K contactor

MK-00511

Micanan Resistor 330 OHM 5Wc/w Leads (For Motor)

072017.0001.S

Overhead Travel Nut for RCH

Teflon travel nut

MX00145

Micanan Brake Assembly for PRO-APT Solenoid NOT included ** DISC

Discontinued. Use part number MX00140

PBS3-BLACK

Replacement Button Only - Black

Replacement button for 02-403P

MO00003

Micanan Compression Spring for PRO-H/HB

0.80 ID x 0.092G x 1.80 Long

18-11379

LiftMaster Compression Spring

MOUNTSHAFT010

Manaras Hoist Shaft Kit for MJH (pre-1998)

Drawing

33106

Overload 5.50 to 8.50A

MGH-6113-ECB-RH

Manaras 3/4 HP 120V 1P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

Installation Manual Sell Sheet

7001-WG-16-MO

Residential Wood Grain Side & Top W/S Medium Oak 16' Long - Painted Screws to Match

Medium Oak retainer with Medium Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

7001-WG-10-DO

Residential Wood Grain Side & Top W/S Dark Oak 10' Long - Painted Screws to Match

Dark Oak retainer with Dark Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

7001-WG-9-DO

Residential Wood Grain Side & Top W/S Dark Oak 9' Long - Painted Screws to Match

Dark Oak retainer with Dark Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

7001-WG-10-CO

Residential Wood Grain Side & Top W/S Cherry Oak 10' Long - Painted Screws to Match

Cherry Oak retainer with Cherry Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

2'6X6SC50

Devanco Loop 2'6" x 6' saw-cut 50' lead-in

Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection