Devanco Canada - Get The Right Garage Door Opener‎ and Parts

PRO-J-7521-U-RH

Micanan 3/4HP 230V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-7581-U-LH

Micanan 3/4HP 208V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5053-U-LH

Micanan 1/2HP 575V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

RELAY068

Manaras Relay SPST 24VDC

PRO-GT-15053-U

Micanan 1-1/2HP 575V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-GT-15083-U

Micanan 1-1/2HP 208V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-GT-15011-U

Micanan 1-1/2HP 115V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-GT-10043-U

Micanan 1HP 460V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-7553-U

Micanan 3/4HP 575V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-7583-U

Micanan 3/4HP 208V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

SPRAY-468

Aluminum Touch Up Spray Paint 350g Nutmeg / Brun Muscade #468

350g can

K29-FDCL-500CCB

LiftMaster FDCL Receiver Logic Board with Battery Rev 500

Replacement kit charging circuit board firmware and battery for FDCL

.319-258-L

Cut-to-Length Torsion Spring .319 x 2-5/8" Left Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-258-Installed

PRO-APTB-7543-U

Micanan 3/4HP 460V 3P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

PRO-APTB-5081-U

Micanan 1/2HP 208V 1P Apartment Trolley Operator With Brake N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-10023-U

Micanan 1 HP 230V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-7553-U

Micanan 3/4HP 575V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

60-7243

Standard Caution Sign English 12" x 24"

60-7248-888

Wheel Chock Safety Pkg incl'd: laminated chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) 88-8 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Fabric Reinforced Tire Rubber
Galvanized Steel Sides
Size: 8" wide x 8" long x 8" high

60-7248-CBI29

Wheel Chock Safety Pkg incl'd: cast ductile iron wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) CBI-29 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Made from Cast Ductile Iron for Impressive Strength
Painted Blue for good Visibility
Completely Reversible for Simple Use
Size: 8" wide x 12" long x 9" high

60-7248-CC07

Wheel Chock Safety Pkg incl'd: cast alum. alloy chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) CC-07 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Reversible Chock Design
One-Piece Cast Construction
Cast Aluminum Alloy
Size: 10" Base x 9" high x 6-1/4" wide

RELAY043

Manaras Relay 4-Pole 24VAC

Used on Manaras MLJ MLH MLT Models

1004-134-16'

Aluminum Bottom Retainer 1 3/4" U-Shape with Reinforcement 16 ft***Actual Length 16'2"****

For door thickness 1-3/4"

27122

Doorlec Electric Motor 1/3HP 208/480/575V 3PH DC321

41C76

LiftMaster Belt Sprocket Cover Kit

Also known as: 041C0076 41C53 41D469 99324608

MP-00204

Micanan Splash Proof Covers PRO-H J HHD GH GHC (Fully Assembled)

drawing

PRO-APTB-5021-U

Micanan 1/2HP 230V 1P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

203301

ELMON Safety Relay Rail 34-32 230VAC/24VAC/DC 1-Channel w/Testsignal

For DIN-rail mounting

CAPXL

LiftMaster Connected Access Portal High Capacity

Connected Access Portal High Capacity Cloud-based access control for residential communities.
Capacities: 4 Controlled Gates/Doors
Wireless Link for up to 8 LiftMaster® Operators
4 to 8 Digit Entry Codes
4 to 6 Digit Directory Codes
50000 Local Resident Capacity

.......more details

MF00006

Micanan Hex Head Bolt 1/4" - 20UNC 1/2" Full Thread

Used on various Micanan operators
2 required per operator

RATCHET_BAR

Ratchet Bar for Holdown Assembly 8-8786 ** Quote Only

HRB-10

High Riser Bracket for 7" Above Dock or Higher 10"

High Riser 10" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

SRB-2

Standard Riser Bracket 2" Above Dock

Standard 2" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

MOUNTSHAFT010A

Manaras Hoist Shaft Kit for MJH (after-1998)

For MJH MJHW/C/X built from 1999-2003

15480

Doorlec Heater Strip 175 W 575 V

DBE-10

Molded Rubber Bumper Black 10" L x 4 1/2" W 3" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles molded bumpers will not warp rust rot or harden.
Bumper comes with 2 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts
10" L x 4 1/2" W 3" Projection

.......more details

LVB1220-11

Laminated Bumper Black 12" Projection Vertical Installation 20" L x 11" W Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB1210-24

Laminated Bumper Standard Black 10" x 24" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1210-14

Laminated Bumper Standard Black 10" x 14" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB1024-11

Laminated Bumper Black 10" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB1012-12

Laminated Bumper Standard Black 12" x 12" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1010-24

Laminated Bumper Standard Black 10" x 24" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1010-14

Laminated Bumper Standard Black 10" x 14" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB912-18

Laminated Bumper Standard Black 12" x 18" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB824-11

Laminated Bumper Black 8" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB812-18

Laminated Bumper Standard Black 12" x 18" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB810-14

Laminated Bumper Standard Black 10" x 14" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

Drawing

TVB436-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TB412-18SF

Steel Faced Laminated Bumper Black 12" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB412-14SF

Steel Faced Laminated Bumper Black 12" x 14" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-18SF

Steel Faced Laminated Bumper Black 10" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-14SF

Steel Faced Laminated Bumper Black 10" x 14" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB412-14SF

Steel Faced Laminated Bumper Black 12" x 14" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB612-24SF

Steel Faced Laminated Bumper Black 12" x 24" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB612-18SF

Steel Faced Laminated Bumper Black 12" x 18" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB612-36

Laminated Bumper Standard Black 12" x 36" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB610-18

Laminated Bumper Standard Black 10" x 18" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB430-11

Laminated Bumper Black 4" Projection Vertical Installation 30" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB412-14

Laminated Bumper Standard Black 12" x 14" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB406-36

Laminated Bumper Standard Black 6" x 36" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

CP-SH-34-1712_SHAFT_ONLY

Lynx Clutch Shaft Only for HDC Operators

Fits all HDC operators - waterproof or not. All HP all years
3/4" x 17 1/2" - 2.15lbs

HINGE-611-PCG

Powdercoated Hinge #6 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #6 - 0.81 lbs
Powdercoated Grey
For use with 7/16" stem rollers

27119

Doorlec Electric Motor TEFC 3/4HP 208/480/575V DC423

Frame size is 56

9-10-2

Lynx Hand Hoist Chain Zinc Plated 26ft / Bag

Zinc plated silver chain

MS-00006

Micanan Trolley Track Set 12 Ga. 16'6" (for 14' h. door) Includes 2 Angles Only

Set includes 2 tracks only
Chain NOT included

Z9211-2

Stationary Cone Tool 2-5/8"

Easily dislodges the cone from the torsion spring

MF00007

Micanan Hex Head Bolt 1/4" - 20UNC 3/4" Full Thread

Used on PRO-GHC
4 required per operator

MF00011

Micanan HH.H. Bolt 3/8" - 16 UNC x 3/4" Long

Used on PRO-GHC
10 required per operator

MH00043

Micanan Flange Bearing 3/8" D **** Replced by MH00096

90-PGR

LiftMaster Parking Gate Radio Mod. Kit

G90PGR includes the limit switch wiring and bracket.
Used on PG HBG and BG models.

31343

Doorlec Sprocket 41B23 - 5/8" bore 2-Hole

PRO-X_MOD-2HP

Micanan Explosion-Proof Modification N-7/N-9 for 1.5HP-2HP

Modification includes an explosion-proof motor explosion proof fittings operator mounted explosion-proof electrical control enclosure and n explosion-proof three button station.

PRO-X_MOD-1HP

Micanan Explosion-Proof Modification N-7/N-9 for 1/2HP - 1HP

Modification includes an explosion-proof motor explosion proof fittings operator mounted explosion-proof electrical control enclosure and n explosion-proof three button station.

3BLM

Exterior Control Station 3 Button N4 with Mortise Lockout in Metal Enclose

Open-Close-Stop
Dimensions: 7" h x 2-3/4" w x 3-1/2" d
Exterior surface mount

3BLM

RCB-TIP

Roller Chain Break Replacement Tip Only *** No Longer Available

Replacement tip only for RCB-2560

.331-6-L

Cut-to-Length Torsion Spring .331 x 6" Left Hand Wound Red/White

Priced per inch - cones and filler sold seperately
For factory installed cones use part no. C-600-INSTALLED
For spring filler use part no. SPRING-FILLER

.331-6-R

Cut-to-Length Torsion Spring .331 x 6" Right Hand Wound Red/White

Priced per inch - cones and filler sold seperately
For factory installed cones use part no. C-600-INSTALLED
For spring filler use part no. SPRING-FILLER

TRACK-SET-2

2" Tracks Set with Wall Brackets Special Order

Custom order to customer's needs
Set includes the vertical and horizontal tracks and wall clips for either wood or steel.
Must spcify if the door has torsion or extension springs if the tracks are going on a wood jam or steel desired radius and thickness of door

MK-00013

Micanan Relay 120VAC coil DPDT (Flange Mount)

.363-334-L

Cut-to-Length Torsion Spring .362 x 3-3/4" Left Hand Wound Green/White

Priced per inch - cones sold separately
For factory installed cones use part no. C-375-INSTALLED

STRUT-2-1/4-9'

Door Strut 2-1/4" Hemmed 9 ft Long

Reinforcement bar 2-1/4"
Electro-Galvanized
22-GA

BI-004

Astragal Bottom Cloth Black PVC Sold by the Foot

MOD060-12FT-MAX

Manaras Auxiliary Trolley #41 Chain Modification Only

Provides drawbar operation of a standard lift door with the use of a jackshaft operator
Includes tracks for doors up to 12' high. Additional fee for over 12'
Maximum door width 22'

PL-B09-CRG-METAL

Lynx Inner Trolley (Metal)

Proline / Lynx 455 Plus trolley slide assembly
For operators built from 2000 +

22016

Doorlec Selector Switch 2 Position OFF/ON

.393-514-L

Cut-to-Length Torsion Spring .393 x 5-1/4" Left Hand Wound Orange

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-514-INSTALLED

50440

Push Button Station 3-Btn with Pilot Light and Key Switch Off/On Nema 4 / 12

Surface Mount
Dust-proof EEMAC 12 and 4

MB-02004

Micanan Electric Motor Only 3/4 HP 110/220V 1PH C-Flange TEFC 56C

C-Flange TEFC electric motor
Fits models: GT GH GHC & GSD

K74-MODELH

LiftMaster Main Wire Harness L3

GMA-3A-5PKG

Fuse Mini Fast-Acting Glass Fuse 3A 250V 5mm x 20mm

5 per pack

WEL-200-T

EMX Wireless Edge Link Transmitter Unit only

Addition transmitter unit for multiple setup

Manual

109007.3901.S

Overhead Receiver 390 Mhz

9 switch trinary fixed code 3-wire gate and garage door receiver

LVB424-11

Laminated Bumper Black 4" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details