Devanco Canada

MW-00020

Micanan Splash Proof Cover Fully Assembled T TB SD

Splash proof cover for models: PRO-T/TB
Same as MP00251

MW-00021

Micanan Splash Proof Cover Fully Assembled

Splash proof cover for models: PRO-H J HHD GH and GHC
Same as MP-00204

MW-00050

Micanan In-Line Torque Clutch Assembly (MP00232)

Friction clutch mounted in between motor and reducer flange
Comes with cover and studs
New part number MP00232

MW-00057

Micanan Splash Proof Cover Light Duty Fully Assembled

Splash proof cover for models: PRO-LJ J LH LHA and GJ
Same as MP-00253

MW-00232

Micanan In-Line Torque Clutch Assembly Modification

Clutch is mounted in between motor and reducer flange
Overall length of operator increases by 3.85"
For models PRO-GH / GHC 1/2hp 3/4hp 1 hp 1.5hp & 2 hp

MW00024

Chain Tensioner for 1"-1" Shafts Inside the Box

Chain spreader for installation with 1" operator shaft & 1" door shaft.
Includes 2 shaft collars and set screws.

MWC-32

Wheel Chock MWC-32 Rubber with Eye Hook

Good stability over others in this class
Long Lasting 80 Durometer rubber
Size: 6-1/2" wide x 9-1/2" long x 8-1/2" high

MWR12

Miller Edge 1-Channel Receiver RF 318 MHz *** To Extent of Inventory

��The MWR12 receiver is designed to receive information from the transmitter and relay it to the motor to stop or reverse motion if the edge comes into contact with an obstruction.
Power requirements: 10 to 40 VDC 10-30 VAC
Output: dry relay contact N/O and N/C 1A @60VAC
Operating temperature: -40C to 60C
Maximum operating distance: 100ft
Electrical configuration: optional N/O or N/C

.......more details

Installation Manual Sell Sheet

MWR22B

Miller Edge 2-Channel Wireless Edge Receiver RF 318 MHz

Power source: 12-24 volts AC/DC nominal Nominal 60 mA 140 mA activated
Output: N.O. N.C
Wire connections: Integral 18” wiring with #6 spade lugs
Antenna: Attached wire or F connector
LED Indicators: Power channel 1
Polycarbonate enclosure

.......more details

MWRTA12B

Miller Edge Wireless Transmitter with Audible Alarm and 1 Channel Receiver

For 2-wire edges
Was previously MWRTA02A now has a new board making installation easier
Includes single channel receiver (MWR12A) and transmitter (MWTA12) with audible low battery alarm.
This feature that activates when the battery has only 25% of its life remaining indicating the battery should be replaced. The alarm sounds for 5 to 10 seconds at 1 to 2 minute intervals.
The receiver operates on either 12 or 24 volt AC/DC and provides N.O. or N.C. output.

MWT12

Miller Edge Transmitter RF in Nema 4 Enclosure *** To Extent of Inventory

The MWT12 safety edge transmitter is designed to provide wireless signal transmission form the safety edge to the motor controls.
It is easily mounted and wired to the gate or door edge sensor. When the sensing edge comes into contact with an obstruction a closed circuit signal is created and is sent to the transmitter.
The transmitter relays the information to the receiver and the receiver passes the signal along to the operator motor.
The gate or door stops movement and will then reverse the direction of travel.
Comes standard with a NEMA 4 weather-proof enclosure. The enclosure can be easily mounted with the four mounting holes and screws provided
Response time: nominal 30msec.

.......more details

MWT12B

Miller Edge Transmitter Binary Nema 4 Enclosure

The MWT12 safety edge transmitter is designed to provide wireless signal transmission form the safety edge to the motor controls.
It is easily mounted and wired to the gate or door edge sensor. When the sensing edge comes into contact with an obstruction a closed circuit signal is created and is sent to the transmitter.
The transmitter relays the information to the receiver and the receiver passes the signal along to the operator motor.
The gate or door stops movement and will then reverse the direction of travel.
Comes standard with a NEMA 4 weather-proof enclosure. The enclosure can be easily mounted with the four mounting holes and screws provided
Response time: 70 milliseconds

.......more details

Installation Instructions MWT12B Spec Sheet MWT12B FAQ MWT12B

MWTA12

Miller Edge Transmitter with Audible Alarm Small *** No Longer Available

The MWTA12 safety edge transmitter is designed to provide wireless signal transmission form the safety edge to the motor controls.
It is easily mounted and wired to the gate or door edge sensor. When the sensing edge comes into contact with an obstruction a closed circuit signal is created and is sent to the transmitter.
The transmitter relays the information to the receiver and the receiver passes the signal along to the operator motor.
The gate or door stops movement and will then reverse the direction of travel.
Comes with an Audible Alarm feature that activates when the battery is running low and needs to be replaced.
Comes standard with a NEMA 4 weather-proof enclosure. The enclosure can be easily mounted with the four mounting holes and screws provided.

.......more details

Installation Manual Sell Sheet

MWTA12B

Miller Edge Transmitter with Low Battery Alarm Small

The transmitter comes standard with a NEMA 4 weather-proof enclosure
Compact design that allow for easy troubleshooting.
The transmitter has an audible alarm that activates when the battery has 25% of its life remaining
Easy to configure · Non-monitored system ideal for operators manufactured prior to: · Doors: August 2010 · Gates: January 2016 · NEMA 4 transmitter built to endure rugged environments
Power Source: (2) 1.5 volts AA lithium batteries
Input: 2-wire N.O. sensing edge

.......more details

Installation manual Spec sheet

MX-00016

Micanan TEFC Motor Upgrade Modification

TEFC motor upgrade for 1-phase belt drive operators

MX-00033

Micanan Trolley Arm Assembly

Kit includes: MM-00031 wall L-bracket (1) MM-00032 trolley arm 105 degrees (1) MM-00033 trolley extension arm (1) MM-00034 trolley arm sliding bracket (1) MO-00004 trolley arm compression spring (1) and MR-00009 red rope c/w handle and warning label (2)