Devanco Canada - Get The Right Garage Door Opener‎ and Parts

B

Molded Rubber Bumper Black 24" L x 12" W 3" Projection 4-Hole 2 Reflectors Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 6 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

DBE-10

Molded Rubber Bumper Black 10" L x 4 1/2" W 3" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles molded bumpers will not warp rust rot or harden.
Bumper comes with 2 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts
10" L x 4 1/2" W 3" Projection

.......more details

LB1012-12

Laminated Bumper Standard Black 12" x 12" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB624-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 24" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TVB620-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LB410-12

Laminated Bumper Standard Black 10" x 12" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB406-36

Laminated Bumper Standard Black 6" x 36" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

MD-00246

Double Sprocket 41B14 / 41A32 with 1" Bushing

Double sprocket for PRO-H/HB

RESET014

Manaras Resettable Overload Fuse 17A 1 Phase

R4

Erone Radium 4-Channel Key Chain Transmitter 433MHz

Designed for the control of automatic closing systems and anti-burglar systems thanks to its very high security coding system (KeeLoq® Hopping code).
The code sent by the transmitter changes at each activation avoiding any scanning and copying risk.
A special algorithm allows to keep synchronized transmitter and receiver.
Range up to 250 m (820 ft)
Ergonomic rugged & durable
Battery: Two 3V lithium battery (CR2016)

.......more details

Wireless System Chart

41A4208-2

LiftMaster Chain Spreader Kit

Chain Spreader Replacement Kit.
For use with various LiftMaster® and Chamberlain® Chain drive garage door opener models.
Complete kit includes: Chain spreader replacement screws and washers.
Also known as: 41A4208 41A4208-2 062210

K20-1050C-2TLP

LiftMaster Electric Motor 1/2 HP 115/230V 1Ph TEFC Logic

K74-18346

LiftMaster Limit Shaft Kit

Compatible with LiftMaster® Model GH 5HP Commercial Door Operators

MG00041

Micanan Spring Clip 7/8" ID Sold Individually

2 required per machine

3BLM

Exterior Control Station 3 Button N4 with Mortise Lockout in Metal Enclose

Open-Close-Stop
Dimensions: 7" h x 2-3/4" w x 3-1/2" d
Exterior surface mount

3BLM

MV-00296

Micanan Wireless Push Button Station OCS for Logic 10.0

Used only on Logic 10.0 program 3.2.5

IRB-RET-HD

EMX Industries Steel Protective Hoods Only Black Fits Old Style IRB-RET Only

Protective Hoods for the Universal Retro-Reflective Monitored Photo Eye System (Item #IRB-RET) by EMX
Easily installed using the existing mounting holes of the Photo Eye
Constructed of zinc plated steel
Black powder-coated finish
Will NOT fit the new IRB-RET UL325-2018 units

H503L5-LH

LiftMaster Ind. Duty Hoist Op. 1/2 HP 208/230-460V VAC 3 Ph Logic 5 Left Hand

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details

VWS-34-BLACK

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Black

Pan head
S point

PRO-J-5083-U

Micanan 1/2HP 208V 3P Jackshaft Monitored ECB N1 Eyes Universal Mount

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

27089A

Genie Washer

Drive shaft washer for PMX500

E/BLOP/127

Automatic Systems Single Channel Loop Detector

Works with the BL229 gate op. logic control

MM00024

Micanan Cam Plate for PRO-HHD

HBSLUD

Stainless Steel Low Headroom Bottom Fixture 2-3" Door 2-3" Track Double End Stile Sold per Pair ** NLA

Manufactured with Heavy Duty 12 ga. Rust-Proof 304 Stainless Steel
Laser Cut for a Clean Finish
For Low-Headroom Track
For 2" or 3" Doors
Fits 2" or 3" Track
Double End Stile

.......more details

HBS23LU

Stainless Steel Low Headroom Bottom Fixture 2-3" Door 2-3" Track Single End Stile Sold per Pair

Manufactured with Heavy Duty 12 ga. Rust-Proof 304 Stainless Steel
Laser Cut for a Clean Finish
For Low-Headroom Track
For 2" or 3" Doors
Fits 2" or 3" Track
Single End Stile

.......more details

PRO-H-7553U-RH

Micanan 3/4HP 575V 3P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

PRO-H-7553U-LH

Micanan 3/4HP 575V 3P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

SPRING002

Manaras Brake Spring

LVB424-11

Laminated Bumper Black 4" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

PRO-HBH10053U-R

Micanan 1 HP 575V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand

1 HP575V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

M6-18

Molded Rubber Bumper Black 18" L x 10" W 6" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
4-1/2" depth
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles. and will not warp rust rot or harden.

.......more details

ALUM-502

Aluminum 24" x 100' Spool Maize / Ivoire # 502

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 502
Reverse side is #431 Bright White

Colour chart

CAP-450-540-110V

Capacitor 450-540 MFD 110/125V with Resistor *** To Extent of Inventory

Same as CP-CAP-COM-450-540
Motor start capacitor

MU22-2WIRE-U-Y

Miller Edge MU22 2-Wire Universal Yellow - Sold per Foot

��Electromechanical edge for sectional doors and aircraft hangars. •The MU22 is a custom edge manufactured to exact specifications. •The MU22 is completely flexible and will contour to curved surfaces. It's profile can also be square rectangular or angled. •Touch sensitive signaling allows immediate reversal or stopping of motion. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •Vertical or horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

SPR50B14X1

Sprocket 50B14 for a 1" Shaft 1/4" keyway

TRACK-3"-RAW-12

Raw Vertical Track 3" 12'-0" Sold per Piece

10FT-CHAIN-LDO

Linear 10ft Chain T- Rail for LD050/LS050/LDCO (HCT10C)

10ft chain-drive T-rail for LDO33 LDO50 LSO50 LCO75 & LDCO800 door operators
Fully-assembled & pre-tensioned

GAREX-DOORFACE

Garex Special Order Door Face Only

Ordered to the customer's exact requirements

MK-00660

Micanan 1 Channel Hand Held Transmitter (for APT applications) Sold Individually

Sold in packs of 10. Priced per transmitter

BK023/PR

Commercial 3" LHR Bottom Brackets Sold as a Pair (L & R)

Same as BB-6-3 reinforced c/w cotter and clevis pins
Use with: 3" straight track
Sold as a pair (includes one left and one right).

26CW94625-CUT

Truck Door Top Panel w/o Hardware (15" x Cut-To-Size Painted White for Whiting Dryfreight

These panels are cut to customer's specifications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white

MGJ-5011U-LH

LiftMaster Medium-Duty Logic Gear-Reduced Op. 1/2 HP 115V 1Ph Left Hand

MGJ is designed for use on rolling grilles and shutters.
Maximum recommended duty cycle: 12 cycles per hour.
Heavy-duty wormgear-in-oil-bath speed reducer
3-button station for open/close/stop functionality
315 MHz radio receiver is integral to the Medium-Duty Logic board
UL325-2010 Monitored Entrapment Capability (provides primary monitored entrapment protection through monitored photo sensors: either CPS-U or CPS-UN4 or a 4-wire monitored edge using the CPS-EI interface)

.......more details

Installation manual Sell sheet

ANT-2

Linear 3ft Mid-Range Antenna (SNE00002)

Antenna for Linear’s 27 MHz mid-range transmitters and receivers
Three-foot whip style
18 feet of coax cable included
”U” bolt included for post mounting
Dimensions: 2.25” W x 39” H x 2” D
Same as: SNE00002

.......more details

28301

Insert Bearing Pillow Block Hy-Speed 1"

ASPP-205

MA003

LiftMaster Electric Motor Only 1/2 Hp 24VDC BM

Same as: MA003M MA-003 MS003 20-60000-1
Used on Liftmaster Mega Arm gate operators

MG00019

Micanan Flat Washer 13/16" ID x 1.5 OD (3/4" Shaft Size)

PRO-H/HB operator parts
2 required per operator

PRO-HB-5011U-RH

Micanan 1/2HP 115V 1P Hoist Op. with Brake N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included
On-Board receiver holds up to 20 transmitters

Installation manual Specification sheet

MP-00008

Micanan Two-Door Interlock Modification

Only allows one door to be opened at one time

MX00137

Micanan PRO-APT Trolley Carriage with Auto Re-Engage Feature (MX00171) *** NLA

New part number is MX00171

DM54LC-COATED

Cable Drum High Lift 54" 400-54HL Specialty Coated Pair

Use for Commercial Highlift Doors
Maximum Door Height 120" + Highlift
Maximum Highlift 54"
Lifting Weight Per Drum 275 lbs.
Resists Chemical/Moisture Corrosion
Abrasion Resistant

.......more details

MD00020

Micanan Sprocket 50B40 X 1-1/4"

.273-334-L

Cut-to-Length Torsion Spring .273 x 3-3/4" Left Hand Wound Orange/Red

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

MU22-2WIRE-LH-G

Miller Edge MU22 2-Wire Left Hand Gray - Sold per Foot

��Electromechanical edge for sectional doors and aircraft hangars. •The MU22 is a custom edge manufactured to exact specifications. •The MU22 is completely flexible and will contour to curved surfaces. It's profile can also be square rectangular or angled. •Touch sensitive signaling allows immediate reversal or stopping of motion. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •Vertical or horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

MW-00050

Micanan In-Line Torque Clutch Assembly (MP00232)

Friction clutch mounted in between motor and reducer flange
Comes with cover and studs
New part number MP00232

RESET010

Manaras Resettable Overload Fuse 13A 1 Phase

34201

Doorlec V-belt Pulley MA20 2" x 5/8" bore

MOTOR274

Manaras Electric Motor 3/4HP 575V 3PH

��This item is compatible with BRAKE011

P220-2K

Heddolf 2-btn Transmitter 8-Dip Switch 318 MHz

Allstar compatible remote

1004-134-12'

Aluminum Bottom Retainer 1 3/4" U-Shape with Reinforcement 12 ft**Actual Length 12'2"***

For door thickness 1-3/4"

GT751L5

LiftMaster Heavy Industrial-Duty Trolley Op. 3/4 HP 115V

Suspended from the ceiling the operators are used on sectional overhead doors with a standard lift.
GT operators are directly attached to drive and control the door
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Requires 828LM MyQ Internet Gateway to connect to MyQ Smartphone App.
High-starting torque continuous duty motor with overload protection
Door speed approx. 11-12 inches per second

.......more details

Installation manual Manuel d'installation Sell sheet Brochure

E3JM-30FT

Omron Thru-Beam Photoelectric Sensor Nema 4 0-30ft Range

Easy-to-wire terminal block
Built-in timer offers selectable ON-delay OFF-delay and one-shot
Relay or transistor output models
Light-ON/Dark-ON operation switch selectable
Model: E3JM-10M4-US

110925

Allstar MVP-QC 3-Btn Quick Code Transmitter 318 MHz *** Discontinued

Compatible with all MVP receivers and operators
Quik-code programming no dip switches
Operate LED
Visor clip included
Power: Two 2032 batteries
Codes: 19683

.......more details

Programming instructions

37302R

Genie C-Channel Belt Extension Kit for Silent Max and Quiet Lift models ** Price by Quote Only

The extension kit for C-channel belt drive garage door opener rails is to be used in addition to a 7' (3-piece) chain rail to accommodate an 8' high door
For Genie silent max 1000 and quiet lift 1200 belt-drive garage door openers only

41A6298

LiftMaster Hardware Installation Bag for 3800

2376.206.35.930

Whiting Torsion assembly .206 wire size 35" spring length 93" shaft

M-VERSION-N4

Manaras Monitored Entrapment Protection Option Upgrade Mont + N4/12 Eyes

Upgrades added when purchasing a commercial operator

JDMG-LG-A030

GDI Jackshaft 24VDC Nema 4

Brushless DC high reliability high efficiency and low maintenance motor
No maintenance GearMotor sealed stainless steel bearings no limits switches no belts or no hydraulic cylinders to maintain
Soft start soft stop
Includes cycle counter timer-to-close 10ft motor wire harness
Battery backup optional (sold separately)

Sell sheet Technical document

029-98105

T-Style Replacement Door White Stainless Steel Package 029-98105

Replacement door size between 72"- 98" wide x 100.25-105" high
Painted white
Stainless steel package
Includes Hinges Rollers and Cable

27-24200

Truck Door Single Torsion Spring Assembly 96/60 for Todco Roll-Up Doors

Single counterbalanced spring design available in 36" 48" and 60" spring lengths.
Shaft Length: 96" Spring Length: 60" Wire Size: .243
Quick and easy counterbalance spring adjustment with easy calibration to door size and weight for effortless operation.
Springs treated with rust preventative
Heavy .243 dia. spring wire
Heavy-duty cast aluminum cable drums hold up to 130" of cable

.......more details

CP-MO-34-575/3

Lynx Electric Motor 3/4 HP 575V

Electric motor only

37222R

Genie Series III Deluxe Wall Console

3 function wall console for use with IntelliG™ and TriloG™ openers.
Same as GBWC-BX
3 function console operates door opener controls lights and security lock out switch.
Not compatible with Series II

MG020-B-2E-04

Miller Edge Sensing Edge Black 2-Wire End Outlet 4ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

MG020-B-2E-05

Miller Edge Sensing Edge Black 2-Wire End Outlet 5ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

BCH751L5-RH

LiftMaster Hoist Op. with Carwash Mod. and Brake 3/4 HP 115/230 VAC Logic 5 Right Hand ***Replaced by CRBH751L5-RH

Industrial Duty Hoist Operator with Damp Environment modification.
Comes with either CPS-UN4
Brake installed on operator

Installation manual Manuel d'installation Sell sheet Brochure

GAREX-EB-PLATE

Garex End Bearing Plate 3-3/8" Special Order

R5221

Sheave Strap 4"

Sheave strap also known as fork only

PEDALU72

Aluminum Pedestal Post 72"

Pedestal post with hood
High quality aluminum
72 inches
Dual face-plate allows for easy wire connections

Shop drawing

BL-09

Barlock Kit Complete for 9ft Wide Door Kit includes hardware bag

Kit includes hardware bag and bars (55-1/2")

Assembly Manual

BL-08

Barlock Kit Complete for 8ft Wide Door Kit includes hardware bag

Kit includes hardware bag and bars (49-1/2")

Assembly Manual

347

Cable Clamps Galvanized 1/4" Sold per piece

Galvanized malleable cable clip

790919

FAAC Control Board 115V for 455D

LDCO800

Linear 800 Newton DC Powered Garage Door Opener Accept Both Belt or Chain Rail *Replaced by LDCO863B*

The energy-efficient DC-powered operator that runs at an AC-equivalent speed.
DC drive motor with soft-start and soft-stop for smooth quiet long-term reliable performance.
Optional Battery Backup available for added peace of mind. Sold separately
Low-power standby mode dramatically reduces energy consumption
Supplies 800 Newtons of lifting force for heavy doors
Compatible with belt-drive or chain-drive T or I beam rails up to 10'

.......more details

Installation manual Sell sheet Remote compatibility chart

MIRM-T2

Miller Edge Patriot 2 Photo Eye Monitored 30ft Non-Contact ** NLA

Attaches directly to a Sectional door.
The photo eyes travel below the door during the closing cycle.
Unlike traditional static mount photo eyes; Patriot travels with the door sensing obstructions prior to contact.
The Patriot2 non-contact system consists of thru beam photo optics.
Emitting and receiving eyes mount into a rigid steel spring loaded retracting housing.
The housings attach to the bottom section of the door and extend below the leading edge of the door providing an invisible infrared light beam of protection.

.......more details

19-50106M

Chain # 50x106 (5-1/2') with Master Link

Also known as: 350120 199023
106 links

K75-34824

LiftMaster Chain Guard Kit

Complete with: Chain Guard Chain Guides and Retainers.

7001-12-CHARCOL

Commercial Side & Top Weather-Strip 12' Long - Charcoal (H)

Charcoal galvanized steel with charcoal dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (10)

CR2025

3V Lithium Button Cell

PBTL-3-102

Key ONLY for PBTL-3 Z102 Sold per Key

Cut Key # Z102
Price for 1 key

BT503L5

LiftMaster 1/2 HP 208-230V/460V 3p Commercial Trolley Operator with a Brake Logic 5 ***No Longer Available

Low profile trolley operator with brake installed
Comes with #48 roller chain

Installation manual Manuel d'installation Sell sheet Brochure

WHITING-DOOR

Whiting Special Order Plywood Core Dry Freight Door Price by Quote Only

Special order to customer's specs
Premium grade 7 ply 3/4” panels manufactured with a medium density overlay (MDO) laminated to smooth hardwood outer veneers of Transportation Core plywood all designed for optimum strength and appearance.
2" track and rollers for durability.
Tongue and groove joint.
2 cable balancer with independent spring for each cable. Springs treated with rust preventative.
4 rows of hinges.

.......more details

28-03090

Truck Door 1" Vert. Track and Right Angle Assbly Curbside (RH) 96.5" Todco Style**To extent of inventory

For Todco style doors
Galvanized steel 14-gauge construction
Includes right angle frame 1" track and operator bracket
Fits doors 72" - 90" high

PRO-HBH-10023U-R

Micanan 1 HP 230V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand (Pro-HHD)

1 HP230V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

LVB620-11

Laminated Bumper Black 6" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

PMR10RGT

Carlo Gavazzi Retro-Reflective Sensor

PMR series sensors have a sensing range up to 32.81 feet and a fixed sensitivity.
Immune to ambient light Selectable output function.
The plastic housing is IP 67 rated and allows cable or screw terminal connections.
Optional timing features include: Delay on operate delay on release or one shot (triggered on leading or trailing edge).
24-240 VAC or 12~240 VDC
5 Wire

.......more details