Devanco Canada - Get The Right Garage Door Opener‎ and Parts

LEVER056

Manaras Disconnect Lever

Works on newer model MJH

TCG-2

LiftMaster Tri-Code Commercial Receiver ** DISCONTINUED

Two channel commercial receiver compatible with Linear Delta Multi-Code and Stanley radios.
Six 3' wired leads

Installation Manual

34538S.S

Genie Magnetic Close Down Limit Switch Assembly 138"

For Chain Glide models

OSH-6114-ECB

Manaras Opera-SH 1HP 120V 1Ph with Electronic Circuit Board

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual Sell Sheet

MA031

LiftMaster Adapter Collars 2/Pkg

For use with Mega-Arm padded arm

MH00015

Pillow Block Bearing 1" UCFL 205-16

ME00028

Micanan Input Shaft Heavy-Duty

41A3589-3

LiftMaster 7ft Belt Assembly for Models '93-2000

Full 7' belt assembly for models 1270 1280 and 1280R

VMD202-100

EMX Vehicle Motion Detector Probe with 100ft Lead Wire

The VMD202 Vehicle Motion Detector is the most advanced single-piece vehicle motion sensor on the market today.
The probe and its electronics are housed in a slim design that is buried next to a driveway.
The VMD202-R Sensitivity Remote Control (sold separately) makes installation and fine tuning simple
Probe assembly and wire are water tight and direct burial compatible
Harness is pre-wired onto lead wire for easy installation
Settings are placed in a non-volatile memory in case of power failure

.......more details

Installation Manual Sell Sheet

788

Fasteners Hex Nut 5/16-18 1000/Box

765

Fasteners Serrated Flange Nut 3/8-16 1000/Box

Serrated flange face to provide locking

775

Fasteners Hex Head Bolt 1/4-20 x 3/4" 1000/Box

1/4" bolt has 7/16" head
Max torque = 6
Full thread

37028C.S

Genie Control Board for Model 2022 ** Repl. by 39537R.S (no cover)

For ReliaG 800 model 2022 gaarage door opener ◾ Genie 37028A Control Board for Genie Models 2022 2024 and 2042 Chain / Belt Drive Openers ◾ Works for the following models only: ◾ ReliaG 800 (2024) PRO Series 1 Piece Rail ◾ QuietLift 800 (2042) ◾ ChainLift 800 (2022)

19-5812

LiftMaster Trolley Chain Pack #48 for 12ft Door

Chain pack only

1116633901.S

Overhead 1-btn Transmitter 390 MHz

Replaces the 1091303901.S
1 channel transmitter opens and closes 1 door
Codes using 9 dip switches with 3 positions
Battery (ALK12V) and visor clip included
Compatible with all Overhead Door 390 MHz frequency garage door openers that were manufactured before 1996.
This was a common remote on the 556C

.......more details

Programming Instructions Instructions de programmation

75-10174

LiftMaster Trolley- Front Idler Assembly

Also known as: 7510174 305115018 711150181 175017 71115211 75-10174

36-RWB-PAIR

Winding Bars Round 36" Set of 2

Cold rolled hardened steel.
Machined to 1/2" at one end with 5/8" outside dia. on the other.
Sold as a pair.

CH505L5-LH

LiftMaster Hoist Op. with Carwash Mod. 1/2 HP 575 VAC 3 Ph Logic 5 Left Hand

Industrial Duty Hoist Operator with Damp Environment modification.
Comes with CPS-UN4 photoeyes
Comes with 02-403P NEMA 4 push button

Installation Manual Manuel d'Installation Sell sheet Brochure

H751L5-LH

LiftMaster Ind. Duty Hoist Op. 3/4 HP 115/230 VAC Logic 5 Left Hand ***Replaced by the RBH751-LH

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details

Installation Manual Manuel d'Installation Sell sheet Brochure

17-6014

LiftMaster Motor Pulley 5L 5/8" ID x 2" OD

Fits model H operator with Logic 5
5/8" ID x 2" OD

42-31246

LiftMaster Terminal Block 20A 600V

3-position

41A3150

LiftMaster Terminal Block with Screws

For model 8355
Same as 041A3150

ETB-311-1/2HP

Doorlec 1/2HP 115V Trolley Door Opener TEFC Motor

Trolley model heavy-duty door operator designed to provide smooth dependable operation of sectional overhead type doors.
DC2000 Logic Controller
Comes with standard O/C/S push button station

MP-00001

Micanan Timer to Close 24V Modification

3-button o/c/s function timer will start counting from fully open reverse and reset from any device
24V modifictation available on control circuit ( R) and ( M) and is included with the new full function smart board (E)

9150000701

Safety Cable for Extension Spring 3/32" 7x7 10' Sold as a Pair

Looped on one end the other is raw (no stops)
Used to wrap around the body of an extension spring to contain the wire should the spring break.

27-20100

Truck Door T-Style Spring Assembly 60" Long

Wire thickness: .24"
Inside diameter: 1.75"
Includes bolt plug and winding plug wound onto spring for stronger design
Cross reference: T#51042 W#2701

8FT-BELT-LINEAR

Linear 8ft Belt Drive Rail for residential openers (HBT8C)

8ft belt-drive T-rail for LDO33 LDO50 LSO50 LCO75 & LDCO800 door operators
Fully-assembled & pre-tensioned
Compatible with Model CHCR-7/8 & CHCR-8 carriage house I-rail conversion kits

7FT-BELT-LINEAR

Linear 7ft Belt Drive Rail for residential openers (HBT7C)

7ft belt-drive T-rail for LDO33 LDO50 LSO50 LCO75 & LDCO800 door operators
Fully-assembled & pre-tensioned
Compatible with Model CHCR-7/8 carriage house I-rail conversion kit

NTE5326

Bridge Rectifier 25A 600V

Bridge Rectifier Converts AC to DC voltage
For powering DC accessories when AC transformer present
Small size with convenient mounting hole in center
Same as MCCM2506-RH

Characteristics

UCFL-1

Self-Aligning Cast Flange Bearing Football Style 1" Bore UCFL205-16

Grey cast iron painted.
Comes with 2x set-screws
Football style 2 bolt

M3-3313

Marantec 3-Button Transmitter 315 MHz 97245 ** Discontinued

Same as part # 65894 97245
Includes battery CR2032
Made in Germany

Instructions

OES-SD16

LiftMaster Optical Edge System 16ft

Sectional door edge kit 16ft (4.9M)

Installation Manual Manuel d'Installation Sell Sheet

13-3510*

LiftMaster Chain Guide ***NLA

This is NLA as a part by itself but may be purchased in a kit K75-18493

CARX-20

EMX Accessory Access Card 5404-1

3.4" x 1.2" x 0.1" (ISO standard size)
Reinforced for long life
Mifare 26 bit Wiegand Format
Durable access card for use on the CR-2000 and PRX-320
Easy and convenient use - just swipe in front of sensor
Secure and can be disabled individually at any time

.......more details

5464.96

Whiting Top Seal Coldsaver 96" L 2-3/16" W

G65_18300

LiftMaster Thermostat Control Heater Fin Type for 115V & 575V Gate Operators

Heater used in BG type gate operators

Installation Manual

1005-1-3/4-12

Aluminum Bottom Retainer U-Shaped

For door thickness 1-3/4"

GRD-2

Linear 2-Channel Delta3 Gate Receiver 310 MHz (DNR00102)

Auto voltage sensing - no jumpers to set
Two Form ”A” (normally open) relays rated at 30 Volts AC/DC up to 5 Amps
Supplied with whip antenna three feet of coaxial cable and bulkhead connector
Power: 12 - 30 VAC or 10.5 - 30 VDC
Codes: 128 (set by dip switches)
RF frequency: 310 MHz

.......more details

Programming Instructions

DTG

Linear Delta3 Safety Edge Transmitter 310 MHz

Activates one Delta-3 receiver for remote stop or reverse safety edge
No cables or coiled wires
Mounting screws (4) supplied
Power: 9-volt battery
Codes: 256 (set by dip switches)
RF frequency: 310 MHz

.......more details

Programming Instructions

12FT-TROLLEY-SET

LiftMaster 12' Track Set for Trolley Operator 10-5812-P (2pcs) *Actual length 179"*

Actual length: 179" (14' 11")

655302

LiftMaster Pneumatic 22' Sensing Edge with 2-Wire Take-Up Reel

85LMC

LiftMaster Plug-In Power Supply

Plug-in jack for easy installation on Liftmaster receivers
Power input level: 105-135AC 24AC output

ME00003

Micanan Clutch Shaft Only for Pro-T/TB 3/4" x 11-3/4" No Kw 1" Thread

MH00099

Micanan Bearing

Fits PRO-APT and PRO-HHD
Requires 2 per shaft
3/4" Bore

MS00003

Micanan Carriage for PRO-APT / T

For model PRO-APT / T

27-20004

Truck Door Dual-Spring Shaft 93" for Whiting Roll-Up Doors

Constructed of 1" outside diameter heavy-duty steel tubing
Holes drilled in one end only for cotter pins the other end is not drilled for flexibility
Cross Reference: W #2528

GREASE

Gear and Rail Grease 3/4 oz Tube *** No Longer Available

A low temperature lithium based grease
To avoid tooth wear premature failure and temperature rise caused by friction by promoting sliding between teeth

82-PX10-28

LiftMaster Screw 10-32x28

.295-2-L

Cut-to-Length Torsion Spring .295 x 2" Left Hand Wound Blue

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.273-2-L

Cut-to-Length Torsion Spring .273 x 2" Left Hand Wound Orange/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.262-2-L

Cut-to-Length Torsion Spring .262 x 2" Left Hand Wound Red/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

.218-2-L

Cut-to-Length Torsion Spring .218 x 2" Left Hand Wound Yellow/Orange

Priced per inch - cones sold seperately
For factory installed cones use part no. C-200-INSTALLED

MOUNTSHAFT018

Manaras Limit Shaft Kit Opera

Drawing

77810.0001

Overhead Door Box Assembly Cushion (#111389.0001.S) ** Price by quote only

Garage door operator bracket for older Overhead Door residential models (Automate 70 Touch n Go R-80 100 100SS 1000) and commercial garage door openers.

ME123-BLK-LH

Miller Edge Black Left Hand Outlet 2-Wire 2" wide x 1-1/2" high Sold by the Foot

Electromechanical slide in edge for sectional doors and sliding gates.
Touch sensitive singaling allows for immediate stopping and reversing of motion
Temperature range: -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Installation Manual Worksheet Sell Sheet

365LMC

LiftMaster Universal Plug-in Receiver 315 MHz

Compatible with any garage door opener with a simple 2-wire dry contact
Includes 2-conductor bell wire
Able to accept 8 Security+ transmitters & 1 digital keypad
Compatible remotes; 893MAX 890MAX 892LT 373LM 371LM 374UT 375UT

Programming Instructions Instructions de programmation

29-31245

LiftMaster Relay 12VDC 250VAC 4-Pin SPDT C & D relay 3-phase only

C & D relay 3-phase only

41A5668

LiftMaster Gear & Sprocket Assembly for ATS211X

For models: ATS211X ATS2113X
For older model ATS211 use part number 41C4470

Installation Manual Manuel d'Installation

41A4885-5

LiftMaster MVIS Pulley/ Worm Gear Assembly

Gear and sprocket assembly for belt drive units after 2002.
Assembly includes: Spring washer thrust washer retaining ring bearing plate two roll pins drive gear and worm gear helical gear with retainer and grease.

Installation Manual Manuel d'Installation

CAM005

Manaras Limit Cam 5/8-18 UNF

Limit cam for Mountshaft009
2 cam's required per shaft

H14G06

Hinge #6 x 14 gauge

Bright zinc plated 14-gauge steel hinge
For use with 7/16" diameter stem rollers
Full body hinge 2-3/4" wide
#6 position
Use between sections 6 and 7
Same as part number 246

.......more details

TRANSF143

Manaras Transformer 120/240-24V 40VA

Transformer 120-240V Primary 24V Secondary 40VA

BRAKE011

Manaras Band Brake Assembly Kit

Does not include solenoid
Replacement brake kit for operators that are belt driven and have a brake. Works with OSH OTBH
Will not work with Gear-Head operators

Installation Manual

7145.96

Whiting Bottom Seal For Coldsaver 96" long

Aluminum retainer sold separately

7470.115

Whiting Side Seal for insulated doors 115" Long

Fits Coldsaver and Tempguard

2234.596

Whiting Coldsaver Bottom Panel 13-1/2" x Max 96" with lock seal and retainer ** Cut to Length

Fits Coldsaver Roll-Up Doors
1-1/8" thick 96" wide
Includes Lock and keeper

108210

Linear 1-Channel Multi-Code Key Ring Transmitter 310 MHz

Open/Close mini remote for 1 door
Compatible with 310 MHz Stanley and Multi-Code receivers
Easy access to battery and coding switches - 10 dip switches
Power: 12-volt battery
Codes: 1024 (set by dip switches)
RF frequency: 310 MHz

.......more details

Programming Instructions

109710

Linear 4-Channel Multi-Code Visor Transmitter 310 MHz

Open/Close remote for 4 doors
Compatible with 310 MHz Stanley and Multi-Code receivers
Supplied with visor clip
Easy access to battery and coding switches - 10 dip switches
Power: 9-volt battery
Codes: 512 per channel (set by dip switches)

.......more details

Programming Instructions

MCT-2

Linear 2-btn MegaCode Visor Transmitter 318 MHz

Activates two 318MHz MegaCode receivers independently
Test/operate LED
Visor mounting clip supplied
Power: 9-volt battery incl.
Codes: 1000000+ (MegaCode format)
Dimensions: 2.16" W x 3.75" H x .95" D

.......more details

Programming Instructions

MDTK

Linear MegaCode Wireless Keypad 318 MHz *** To extent of Inventory Repl. by LPWKP-G

Activates multiple MegaCode receivers
User selects 1 to 6 digit PIN number or 1 to 6 letter PIN name
Programming is easy via the keypad; MegaCode receiver auto-learns PIN
Backlit keys for easy viewing
Wall mounting hardware (2 screws and anchors) supplied
Power: 9-volt battery included

.......more details

Programming Instructions

15.1

Whiting Truck Door Stainless Steel Center Hinge

RV-300

3" Vinyl Insert for Brush Retainer per foot

Color: Black

RV-100

1" Vinyl Insert for Brush Retainer per foot

Color: Black
Fits in light brush retainers

1003-3"-200FT

Bottom U-Rubber 3" Black 200' Long

200ft spool of vinyl insert.

1006-1-3/8-8'

Rigid Vinyl Bottom Retainer U-Shaped 8' Long

Black with flexible fin to touch door face.
For door thickness 1-3/8"

1005-1-3/8-16'

Aluminum Bottom Retainer U-Shaped 16' Long

For door thickness 1-3/8"

1004-134-24'

Aluminum Bottom Retainer 1 3/4" U-Shape with Reinforcement 24 ft***Actual Length 24'4"****

For door thickness 1-3/4"
DIE # ES19244

1003-1-5/8-16'

Aluminum Bottom Retainer L-Shaped

For 1-5/8" thick doors.

PULL-CHAIN

Pull Chain Spring Only 12" Long

Spring Only for pull chain device
Used with a hand chain for full vertical doors.
Eliminates the need for leaf bumpers

7001-8-WHITE

Commercial Side & Top Weather-Strip 8' Long - White (W)

White galvanized steel with white dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

25-42-130

Extension Spring 7' Door - 130 lbs Yellow

Double - Loop
25" long 42" stretch 130 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

95-00114

Truck Door Rivet 1" Stainless Steel

Stainless steel construction
Round head design
Cross Reference: T #89217-0032

26-40026

Truck Door U-Channel Seal Retainer 96" Long for Whiting DryFreight Doors *** DISCONTINUED

Aluminum extrusion construction
Cross Reference: W #1801

Z9997

Hand Chain 25' for Manual Chain Hoists

Not SAE rated.
Designed for approx. 35 lbs

Z9404

Coupler 1-1/4" Bore Adjustable

Malleable iron for strength
With 2 jam nuts
1-1/4" Bore with 1/4" keyway

SF600U

Spring Fitting 6" Pair Universal Thread Stationary + Winding for 1" Shaft

Universal thread and is available for 1" or 1.25" Bore - must specify when ordering.
Pair includes: (1) winding & (1) stationary.
Not single thread.
Winding bar hole 5/8"

H11G12

Hinge #12 x 11 gauge

11 gauge # 12 hinge - 1.00 lbs
Bright zinc-plated steel construction
For use with 7/16" stem rollers

H11G02

Hinge #2 x 11 gauge

11 gauge # 2 hinge - 0.69 lbs
Bright zinc-plated
For use with 7/16" stem rollers

CB5320500

Cable 5/32" 7x19 500' Galvanized

Galvanized cable 5/32" 7x19 500ft spool.
Cable break strength: 2800 lbs

Comparison charts

RN1324

Roller 2" Nylon 4" stem 13 ball White Sold per Roller

White Nylon Roller Wheel Diameter: 2"
Working Length: 3.75" Overall Length: 4.71"
Box qty: 100 Box weight: 32.2 lbs (2-4-13 White Nylon)

RN0024

Roller 2" Nylon 4" stem Black

Black Nylon Roller Wheel Diameter: 2"
Working Length: 3.75" Overall Length: 4.75"
Box qty: 250 Box weight: 58.2 lbs (2-4 Black Nylon)
No bearings in head

75LMC

LiftMaster Illumintaed Wall Button 2 wire Universal ** To Extent of Inventory

2 wire wall button for all openers that will activate by connecting the two wires together.

25-01431

Truck Door Stainless Cables 105" 5/16 eye 7x19 Pair for Roll-Up Doors

Works with both Whiting and Todco doors
Cable size: 1/8 "

23-2016

LiftMaster Limit Switch

Limit Switch for the VSL595

.295_2"-LH

Torsion Spring .295 x 2" x 12ft LH Blue

Wire size: .295
Inside diameter: 2"
Length: 12 ft

19054

Doorlec VBelt 5L380

works on model SWGO

25-42-50

Extension Spring 7' Door - 50 lbs Red

Double - Loop
25" long 42" stretch 50 lb load
Sold individually
Rated for 10000 cycles
Same as part number 105

Spec Sheet

1A4324-EZ

LiftMaster Steel Hood EZ Mount Bracket with Adaptor Plate (75-12362/ 001A4324)

Heavy-gauge steel bracket with EZ mount adapter plate mounting bolts nuts and washers.
Adapter plate holds mounting bolts in place for ease of mounting.
Cannot be used with Model GH 3HP.