Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MIRCU-02

Miller Edge Universal Non-Monitored Interface

Converts a monitored pulsed signal to a non-monitored normally open signal
Creates a Fail Safe signal; reports a fault when power is lost
Ideal for use with pre-2010 commercial door operators

Installation instructions Sell sheet

MTR1

Linear 1-Channel Visor Transmitter 318MHz *** No Longer Available

Activates one MegaCode receiver
Test/operate LED
Visor mounting clip supplied
Visor clip mounts vertical or horizontal
Power: One 2032 battery
Codes: 1000000+ (MegaCode format)

.......more details

Programming instructions Instructions de programmation

MTR3

Linear 3-Channel Visor Transmitter 318MHz ** To extent of Inventory

Activates three MegaCode receivers
Test/operate LED
Visor mounting clip supplied
Visor clip mounts vertical or horizontal
Power: One 2032 battery
Codes: 1000000+ (MegaCode format)

.......more details

Programming instructions Instructions de programmation

K75-37549

LiftMaster Disconnect Kit for SL595U

Compatible with LiftMaster SL595UL heavy-duty vehicular slide gate operators
Allows manual operation of your gate operator

H14G02-BLACK

Hinge #2 x 14 gauge Black Powder Coated

Black powder coated 14-gauge steel hinge
For use with 7/16" diameter stem rollers
Full body hinge 2-3/4" wide
Individually wrapped

BK000-B/BLACK

Residential Top Roller Bracket Adjustable 2-Bolt Black Powder Coated Sold per Piece

Sold per piece - not sold as a pair
Meant for 2" hardware
Individually wrapped

VMD202-50

EMX Vehicle Motion Detector Probe with 50ft Lead Wire

The VMD202 Vehicle Motion Detector is the most advanced single-piece vehicle motion sensor on the market today.
The probe and its electronics are housed in a slim design that is buried next to a driveway.
The VMD202-R Sensitivity Remote Control (sold separately) makes installation and fine tuning simple
Probe assembly and wire are water tight and direct burial compatible
Harness is pre-wired onto lead wire for easy installation
Settings are placed in a non-volatile memory in case of power failure

.......more details

111396.0004

Overhead Brake Kit Model H 1/2HP 1PH

Installation instructions

CAP378

Capacitor 110/125VAC 378-454MFD

378-454 mF 125 VAC 50/60 Hz
Used on 1/2 HP LiftMaster operators

S505AL

LiftMaster Monitored Small Profile Resistive Edge w/Aluminum Channel 5ft

Meets 2016 UL 325 requirements Edge sends signal to stop and/or reverse operation when sensing obstructions
Fast easy to install mounts vertically or horizontally
Compatible with Wireless edge kit LMWEKITU Transmitter LMWETXU and LiftMaster Gate Operators with Monitored Safety Inputs

Installation manual

M15A

Safety Inertia Brake 2" Bore 13727 Torque PCM15AP

Provides a bearing to support the shaft and prevent the fall of a door if sudden acceleration occurs.
Ideal for commercial and industrial use; specifically with rolling shutters and balanced and well maintained rolling doors.
Fully resettable and reusable after lockout ocurrs.
Commonly paired with commercial safety bottom brackets in sectional door applications.
Fits 2" shaft
Note: Sectional torsion door systems must be well maintained to ensure desired inertia brake activation.

.......more details

M15A Reference Manual Technical data Sell sheet

2376.192.29.910

Whiting Torsion assembly .192 wire size 29" spring length 91" shaft

This is a full balancer assembly

MP00069

Micanan Jackshaft w/Aux Trolley Assembly Mod. 7ft High Door #41 Trolley Drive Chain

Provides an auxiliary trolley assembly where otherwise a jackshaft operator may be preferred
NOTE: Operator must be supplied with reverse limits
If purchasing for field install the limits on the operator would need to be reversed

USVD-BD

EMX Board Only for Ultra Sonic Vehicle Detector

Replacement board only for USVD-4X

L-14-50-0-D

Cable Tie Standard 50 LB Black 14" Nylon 500/pkg

Ultraviolet Resistant
Length: 14.56" / Width: .180" / Thickness: .052" / Diameter: 4.125"
Low insertion and pull through force
Advanced pawl and teeth design
Angled tail provides quicker initial insertion alignment
Tail finger grips allow easier handling and tightening

.......more details

1004-2-10'

Aluminum Bottom Retainer 2" U-Shape with Reinforcement 10 ft***Actual Length 10'1"***

For door thickness 2"

K76-34697

LiftMaster APS Encoder 24V

For use with various LiftMaster® Commercial Slide and Overhead Gate Operators

SETR2641AM2BP

Erone 2-Channel Mini Transmitter with Paradox Tag Blue 433MHz

With built-in Paradox tag
Heavy-duty construction
Elegant & easy to carry
Unobstructed range: 656 ft (200m)
60 x 36 x 16mm (2.35 x 1.4 x 0.6in)
Two lithium batteries (CR2016) included

.......more details

Wireless System Chart

CAP425

Capacitor Motor Start 125VAC 425MFD

Motor Start Capacitor 125V 425 MFD

29150

Doorlec Transformer 600Vpr 120V sec. 50VA

F520-3.15-SB

Fuse 5 x 20mm 3.15A 250V Slow Blow 5/Pkg

FEP100N

Pneumatic Safety Edge End Caps Included Sold by the Foot

Must specify if L-retainer is required

LIMIT017

Manaras Micro Limit Switch SPDT

CAP001 sold separately

SPRAY-431

Aluminum Touch Up Spray Paint 350g Bright White / Blanc Pur #431

350g
Replaces Gentek #801

20104

Doorlec Coupling Spring 5/8" LJH

K20-3200C-5

LiftMaster Electric Motor 2 HP 575V 3PH CF

Also known as: 20-3200C-5 K20-3200C5 K20-3200C-5-H27

COUPLER-LJ-OHD

Coupler Love-Joy for Overhead Door

PRO-GH-10011U-L

Micanan 1 HP 115V 1P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

620-100990

Linear Heater Kit Assembly 230V Cage Style

Cage style heater is suited for large post mount operators (HSLG GSLG VS-GSLG SWG VS-SWG)

218757

Torque Force Spring Failure Device 1" Shaft Left Hand Side DT0054 126474

For springs 2" up to 6"
This device can be applied on Industrial OH doors that are manual or motor operated
Must be installed on a keyed shaft
The both in the Euro model is metric only difference from 218757

PRO-GH-5053U-L

Micanan 1/2HP 575V 3P Gearhead Operator N1 Eyes Monitored ECB Left Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

PRO-GH-5021U-R

Micanan 1/2HP 230V 1P Gearhead Operator N1 Eyes Monitored ECB Right Hand (PRO GHE)

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

DW-3S-200

Fraba Air Wave Switch Small Housing NOC

Fraba DW3S-200 air switch
Normally Open Contact (NOC)
Small Housing does not come with copper end
Screw Type Connector
Housing dimensions: 101x48.5x48 mm (3.97x1.91x1.89 '')
Housing: ABS Switch: PA6V0

.......more details

Operating Instructions

PRO-HB-7525U-LH

Micanan 3/4HP 220V 1P Hoist Op. with Brake N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

PRO-HB-7543U-RH

Micanan 3/4HP 460V 3P Hoist Op. with Brake N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

PRO-H-7521-U-RH

Micanan 3/4HP 230V 1P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

K71-D575-1

LiftMaster Drum Brake Kit 3 Ph 575V (Late Model Logic 5 Shoe and Drum Models)

Internal Solenoid Drum Brake with Cable Replacement Kit.
Compatible with LiftMaster® Logic 5.0 Model T SD J H and HJ Industrial-Duty Operators.
Complete service kit includes: Solenoid Cover Brake Solenoid Brake Drum Cable Mounting Plate and Installation Hardware.
Quiet preferred sound profile
Industry benchmark stopping performance with adjustability
Significantly reduced modes of failure

.......more details

Installation manual Manuel d'installation

PRO-J-10043-U-RH

Micanan 1HP 460V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

SETR2681AM2K

Erone 2-Channel Mini Transmitter 868MHz

Wireless System Chart

MM-00360

Micanan Circuit Board Support U-Bracket

MK-00016

Micanan Fuse Holder

MK-00222

Micanan Transformer 460V-24V-100VA

MK-00931

Micanan Single Btn Mini Transmitter ** Discontinued

ALUM-509

Aluminum 24" x 100' Spool Midnight Surf / Vagues de Minuit # 509

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 509
Reverse side is #431 Bright White

Colour chart

MV-00305

Micanan Wireless Pull Cord

MV-00304

Micanan Wireless Key Switch

MV-00010

Micanan 3-btn O/C/S Nema-4 Pushbutton Control Station

Surface mount
Metal Housing

MV-00006

Micanan 3-btn O/C/S w/Key Lock-Out Nema-1 Pushbutton Control Station

Flush mount

RBH103L5-LH

LiftMaster 1 HP 208/230/460 VAC 3 PH Comm. Hoist Op. Logic 5 Left Hand

H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door.
With the addition of the 828LM MyQ technology enables the user to monitor and control their operator and light with their smartphone tablet or computer.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.
Security+ 2.0™ safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you.

.......more details

RBH103L5-RH

LiftMaster 1 HP 208/230/460 VAC 3 PH Comm. Hoist Op. Logic 5 Right Hand

H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door.
With the addition of the 828LM MyQ technology enables the user to monitor and control their operator and light with their smartphone tablet or computer.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.
Security+ 2.0™ safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you.

.......more details

DM-100

Skylink Swing Door Opener with Electro-Magnetic Lock ***NLA

Can be installed on most doors including wood and metal doors.
Hit and Stop feature ensures safety operation.
Fail safe operation - Door can be open/close freely during power outage
Optional audio warning as an indication when the swing door opener is operating
Can learn up to 16 remote controls

SPR60B18X1

Sprocket 60B18 x 1" Bore 1/4" KW

Same as MD00425

.283-6-R

Cut-to-Length Torsion Spring .283 x 6" Right Hand Wound White

Priced per inch
For factory installed cones priced seperately - use part no. C-600-INSTALLED

PRO-J-5053-U-RH

Micanan 1/2HP 575V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5021-U-RH

Micanan 1/2HP 230V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5011-U-RH

Micanan 1/2HP 115V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-5011-U-LH

Micanan 1/2HP 115V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

K29-FDCL-500CCB

LiftMaster FDCL Receiver Logic Board with Battery Rev 500

Replacement kit charging circuit board firmware and battery for FDCL

.393-334-R

Cut-to-Length Torsion Spring .393 x 3-3/4" Right Hand Wound Orange

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

PRO-TB-10021-U

Micanan 1 HP 230V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-5081-U

Micanan 1/2HP 208V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-5083-U

Micanan 1/2HP 208V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-5011-E

Micanan 1/2HP 115V 1P Trolley Operator NM ECB No Eyes

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Non-Monitored board NO photocells
On-Board receiver holds up to 20 transmitters

MB-05504

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 56C

Fits GT GH GHC & GSD

811-11

Wheel Chock 811-11 Orange Urethane

Not For Use on Ice
High Visibility
Orange Urethane
Size: 11" wide x 8" long x 8" high

60-7248-MWC32

Wheel Chock Safety Pkg incl'd: chock w eye hook wall bracket 15' chain 3/8"x1 7/8" anchors (4) 3/16" quick link (2) & English caution sign

System Includes (1) MWC-32 Chock Bracket Tie Back Chain English Caution Sign and (4) Wall Bracket Anchors
Good stability over others in this class
Long Lasting 80 Durometer rubber
Size: 6-1/2" wide x 9-1/2" long x 8-1/2" high

60-7248-CBI29

Wheel Chock Safety Pkg incl'd: cast ductile iron wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) CBI-29 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Made from Cast Ductile Iron for Impressive Strength
Painted Blue for good Visibility
Completely Reversible for Simple Use
Size: 8" wide x 12" long x 9" high

60-7248-CBI087

Wheel Chock Safety Pkg incl'd: yellow ductile iron chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) CBI-087 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Cast Ductile Iron for Impressive Strength
Painted Yellow for High Visibility
Size: 8-1/4" wide x7-1/4" long x 8-1/2" high

MD-00004

Sprocket 410B12 x 1" 1/4" KW 2 SS 5/16"

MF00009

Micanan Hex Head Bolt 1/4" - 20 UNC x 2-1/4" Partial Thread

Used on PRO-HHD
1 required per operator

SRB-6

Standard Riser Bracket 6" Above Dock

Standard 6" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

SRB-5

Standard Riser Bracket 5" Above Dock

Standard 5" Riser Bracket for 6" Above Dock Door or Less
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

E/1929/070

Automatic Systems Spare Arm 14'-9" (BL229)

Used on the BL229 gate op.

748

Fasteners Self Drill & Tap Tek Screw 1/4-20 x 3/4" (#2PT) 1000/Box

Indented Hex Washer Head
7/16" Head
Max RPM = 2000
#2 point = shorter cutting edge (more thread)

15480

Doorlec Heater Strip 175 W 575 V

MM00447

Micanan Idler Wheel PRO-APTC

LVB824-11

Laminated Bumper Black 8" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB812-12

Laminated Bumper Standard Black 12" x 12" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB420-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

Drawing

LB412-14SF

Steel Faced Laminated Bumper Black 12" x 14" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB610-18SF

Steel Faced Laminated Bumper Black 10" x 18" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

8065

LiftMaster Contractor Series 1/2 HP AC Chain Drive Garage Door Opener **DISCONTINUED

MyQ® Technology enables you to securely monitor and control your garage door opener and houselights with your smartphone tablet or computer.
1/2 HP AC motor with industrial-strength chain drive provides steady performance and lifting power.
Security+ 2.0™ safeguards your household – with every click a new code is sent to the garage door opener so that the door opens only for you.
The Protector System® has safety sensors that project a light beam across the garage door opening automatically reversing the door if anything interrupts the beam.
Comes with: 1-Button Remote Control (891LM) Door Control Button (883LM)

LVB430-11

Laminated Bumper Black 4" Projection Vertical Installation 30" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

44-60-280

Extension Spring 10' Door - 280 lbs Gold ** By Quote Only

Clipped ends
44" long 60" stretch 280 lb load

WRW

Erone Wiegand Wireless Receiver 433MHz

433 MHz radio frequency systems offer longer range (up to 250m (820ft) less interference jamming and excellent reliability.
KeeLoq® Rolling Code technology ensure ultra-secure transactions.
Output: Wiegand 26 bit
Power requirements: 12 or 24V (AC or DC)
Dimensions: 105 x 45 x 28mm (4.3 x 1.75 x 1.1in)
Compatible with Centaur and any 26 bit Wiegand-capable systems

.......more details

Wireless System Chart

31343

Doorlec Sprocket 41B23 - 5/8" bore 2-Hole

2806.139*130

Whiting Spring Assby .139 x 2-3/16 x 13" L Roadside

Replacement torsion spring with cones
Specs: .139 x 2-3/16" x 13" Long
Roadside
For Curbside order part # 2807.139.130

SL585103U

LiftMaster Industrial Slide Gate Op.1 HP 208/230/460V 3 Phase - Heater NOT Incl. ***NLA

POWER: 115/208/230 VAC. Single Phase
ACCESSORY POWER: 24VAC 500mA max.
MONITORED SAFETY INPUTS: 3 Main Board 3 Expansion Board.
TEMPERATURE SPECIFICATIONS: Without Heater: -4°F (-20°C) to 140°F (60°C). With optional heater -40°F (-40°C) to 140°F (60°C).
Heater option: HTRNB or NTR460 for 460V operators
UL USAGE CLASSIFICATION I II III and IV.

.......more details

Installation manual Manuel d'installation First step for installation Première étape pour l'installation Sell sheet Brochure Wiring diagram Schéma câblage

BB-1

Rubber Button Cover Black for 3BLM PBS

Rubber button cover only

MX-00016

Micanan TEFC Motor Upgrade Modification

TEFC motor upgrade for 1-phase belt drive operators

IRB-RET-HD

EMX Industries Steel Protective Hoods Only Black Fits Old Style IRB-RET Only *** No Longer Available

Protective Hoods for the Universal Retro-Reflective Monitored Photo Eye System (Item #IRB-RET) by EMX
Easily installed using the existing mounting holes of the Photo Eye
Constructed of zinc plated steel
Black powder-coated finish
Will NOT fit the new IRB-RET UL325-2018 units

ALUM-5P3

Aluminum 24" x 100' Spool Espresso # 5P3

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 5P3
Reverse side is #431 Bright White

Colour chart

BOARD060R

Manaras Replacement Circuit Board (No Monitoring)

Control board for BOARD065

3PHCONV

LiftMaster 3-Phase Conversion Kit

The transformer kit will convert an input voltage of 208 / 240 / 480 / 575 3 phase VAC to an output voltage of 120 VAC.
Included in New 3-Phase Transformer Kit: Transformer with bracket (2) Cable ties Bushing Wire sleeve 2’ (.61 m) (5) Wire nuts Mounting bracket 10-36745 and mounting hardware (for installing on CSW24U operators) (6) Operator rating replacement labels Accessory outlet rating replacement label
Compatible with SL3000501U SL3000101U CSW200501U and CSW200101U AC gate operators only

3PHCONV_Installation-manual 3PHCONV_Manuel-installation

VWS-34-MED-OAK

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Medium Oak

Pan head

2650-112-11

Linear Cold Weather Package HSLG 230V

Factory Option 2650-112-11 Cold Weather Package for 230-volt HSLG
Package includes: Arctic Oil Heater Cogged Belt
This factory option is only available for purchase when buying your gate operator.

7-19-1

Lock Bar Guide Only

36190S.S

Genie Control Board 6-Terminal *** No Longer Available

Replaces board # 34514R # 20380R
36190S.S is a six terminal board for use primarily with ML Chain Glide devices.
Replacement board for Chain Drive models: IC250B PMX300 PMX500 ICB and 496.696 CD/B
Replacement board for Chain Glide models: GCG350 GCG350L GCG350M PCG400 PCG450 PCG500ML PCG600 PCG650 H2000C OCG510 OCG550 OCG600ML OCG710 and OCG800ML