Devanco Canada - Get The Right Garage Door Opener‎ and Parts

K081C0168

LiftMaster Screw Drive Rack

Also known as: 081C0168 81C168
This replacement screw drive rack is not compatible with LiftMaster® Models 3130 or 3240

ETH-A

Doorlec Trolley Type Apartment Op. 1/2 HP 120V Head Only

This operator can be wire to receive radio and photo electric control systems loop detectors etc..
Headroom Required: 2" minimum at doors highest arc of travel

SF514-S

Spring Fitting 5-1/4" Stationary Side Only for 1" & 1-1/4" shaft

Can be used with either 1" or 1-1/4" winding cones
Includes: (1) stationary side only.
2 x 3/8-16 thread holes at CC=4.25"

BRX10

GDI Brake Kit Brake Kit with Pull-rods; Axial

E/1929/071

Automatic Systems Round Arm Ass'y 16'-5" (BL229)

Used on the BL229 gate op.

MGH-6113-ECB-LH

Manaras 3/4 HP 120V 1P Jackshaft with Elect. Circuit Board Left Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

AW-10

Miller Edge Air Wave Switch Only No Enclosure

Air pressure is lead via a hose or pipe to a diaphragm contact. This contact converts the positive or negative pressure into an electrical contact and pulse.
Applications: commercial sectional doors rolling doors and mass transit
Works on doors up to 60ft
Can be used with standard pneumatic hose and Miller Edge extrusion
Sensitivity: 2mm to 500mm
Ambient temperature range: -49F to 180F

.......more details

Instruction manual Sell sheet

MOUNTSHAFT015

Manaras Hoist Shaft Kit for OGH

112561

Allstar MVP-RE 24V 8 Wire Receiver 288 MHz *** NLA

Three channels – three relay outputs
8-wire operator connection
Wire whip antenna with “F” connector
Compatible with Allstar Classic Allister and Pulsar dipswitch transmitters and MVP quik-code transmitters
Power: 24 VAC/VDC
Codes: 19683

.......more details

LZE500

Erone L & Z-Bracket for Maglock ESM500

P-75H

End Plug for 3/4" ID Rubber Air Hose w/ Center Hole Qty 1

Sold per plug

MX00128

Micanan Clutch Assembly for PRO-GOHD

XBA15

NICE Aluminum Bar with 3M White Paint 69mm x 92mm x 3150mm

CAP475

Capacitor 125VAC 475MFD

Motor Start Capacitor 125V 475 MFD

MT22-MON-GRY-LH

Miller Edge 4-Wire Monitored Pressure Sensitive Edge Gray Sold per Foot

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

FLO1R-SA

NICE 1-btn Keychain Remote 433.92 MHz

Rolling code No internal dip switches programming with the reciever
Battery included: 12V (GP23A)
Dimensions: 72 x 15 x 40 mm

CH503L5-RH

LiftMaster Hoist Op. with Carwash Mod. 1/2 HP 208-230V/460 VAC 3 PH Logic 5 Right Hand

Industrial Duty Hoist Operator with Damp Environment modification.
Comes with CPS-UN4 photoeyes

CH503L5-LH

LiftMaster Hoist Op. with Carwash Mod. 1/2 HP 208-230V/460 VAC 3 PH Logic 5 Left Hand

Industrial Duty Hoist Operator with Damp Environment modification.
Comes with CPS-UN4 photoeyes

CP-PU-DRV-78-8

Lynx Drive Pulley 7/8" x 8" 4L for Jackshaft Ops

SS-STRUT-10

Strut Stainless Steel 2-1/2" x 10ft 16-Ga

MLC-K72

Miller Edge Light Curtain Monitored 6ft Pulsed

Light curtain made up of a series of thru-beam photo eyes designed to provide a dense barrier of protection for motorized or high speed doors.
Ideal for environments that require expanded protection for protruding parts that may not be detected by standard single-beam photo eyes mounted 6" above the floor.
Ability to span up to 32' wide
Universal mounting brackets included
IP67 waterproof housing
Operating temperature: -40F to 140F

.......more details

Installation manual Sell sheet

WHITING-PW

Whiting White Urethane Topcoat Option Dry Freight Door Panel

This is an option when ordering a panel

SL595203UL

LiftMaster Dual Voltage Slide Gate Op.2 HP 208/230/460V 3 Phase - Heater NOT Incl. UL325

UL 325 compliant system.
Power: 208/230/460/575 VAC. 3 Phase.
Accessory power: 24VAC 500mA max.
Monitored safety inputs: 3 Main Board 3 Expansion Board.
Temperature specs: Without Heater: -4°F (-20°C) to 140°F (60°C). With optional heater (HTRNB: HTR460 for 460V operators): -40°F (-40°C) to 140°F (60°C)
Gate travel speed: 12 in. per second.

.......more details

Installation manual Manuel d'installation First step for installation Première étape pour l'installation Sell sheet Wiring diagram Wiring diagram 575V

E/BLOP/276

Automatic Systems Audible Alarm for BL229

K20-3050C-4P

LiftMaster Electric Motor 1/2 HP 208/230/460V 3Ph L3 L4 L or M

Standard 1/2 hp motor
This is a replacement Motor Kit (1/2 HP 230/460V 3PH CF)
For use with various LiftMaster® Three Phase Gear-Reduced Commercial Door Operators and Slide Gate Operators
Also known as: 6002242 K20-3050C-4 203050 K20-3050C4 20-3050C-4 203050C4 20-3050C-4P

050DCTWFLK

LiftMaster Receiver Logic Board DC. WiFi Lock Capable Sec+ 2.0 ***replaced by 050DCTBFLK***

This is 315MHz Security+ 2.0® Lock Capable Receiver Logic Board featuring Wi-Fi® and powered by myQ®.
For use with various LiftMaster® DC Chain or Belt Drive Garage Door Opener models; manufactured after 2017 only.
The unit will feature a yellow learn button and two lock terminals

K75-10406

LiftMaster Drive Chain Connector Link Kit APT

Also known as: 30515363 305105363

F520-3.15-SB

Fuse 5 x 20mm 3.15A 250V Slow Blow 5/Pkg

AM-PC

Linear Proximity Cards - Linear Format ACP00739 25/Pkg

The Model AM-PC Proximity Card is a Wiegand format proximity type access control card with a slot for attaching to a key ring use with AM-PR proximity reader.
Passive operation
Low-cost
Durable
25 piece bulk pack minimum order
Dimensions: 3.4" L x 1.9" W x 0.13" Thick

.......more details

FEP100N

Pneumatic Safety Edge End Caps Included Sold by the Foot

Must specify if L-retainer is required

28-32082

Truck Door 2" Horizontal Track with 8" Radius 120" Curbside (RH) for Whiting Roll-Up Doors

SPECS: Length: 120" Fits door sizes: Greater than 96" high
Cross Reference: W #11-2
Galvanized steel 14 gauge construction
Tongue and groove for proper alignment at joints
8" radius
For use with 2" diameter steel or nylon rollers

.......more details

27020

Doorlec Electric Motor TEFC 1/3 HP 115/230V DC301

10PBJL

Jamb Push Plate SS with Handicap Logo Only

1⁄16 inch thick stainless steel for maximum durability
Concealed fasteners to minimize vandalism
Compatible with both surface and flush mount boxes
Faceplate Material 16 gauge 304 2B Stainless Steel
Backplate Material 1⁄8 inch thick Aluminum
Mounting Screws Stainless Steel 6-32 × 1 in & 8-32 × 1 in Allen Head Size: 5⁄64

.......more details

PRO-APTC-5011-U

Micanan 1/2HP 115V 1P Apartment Trolley Op. Photo Eyes Monitored ECB

Low clearance design for APT applications (8.5")
Door speed: 7" per second
N-4 Micanan compatible monitored photocells included
Monitored board
Side access hinged cover for easy access to controls
Three button open-close-stop control station Nema-1

.......more details

Installation manual

SSSS-1-6FT

Solid Shaft 1" Keyed Stainless Steel 6 ft

303 series Stainless Steel

BEA-10-BR3X

BEA Programmable 3 Relay Logic Module w/13 Functions

For use on automatic pedestrian doors access controls industrial automation and single-occupancy restrooms. •13 Functions Include:
Timer
Ratchet/Latching
2 Relay Sequence + Inhibitor
2 Relay Sequence + Door Position
Deactivation Timer

.......more details

Product guide

CSW200501U

LiftMaster Commercial High-Traffic Swing Gate Operator 1/2 HP 120-240VAC

First choice for heavy-traffic applications such as large gated communities residential developments commercial complexes and private estates.
Unlike other systems the CSW gate operators are designed with a "non-scissor action" swing arm to greatly reduce the risk of injury
Bi-Part Delay Monitors and adjusts speed and position of each wing to ensure primary gate closes last.
Synchronized Close Simultaneously closes gates.
Pre-Motion Warning Alarm Activates onboard alarm three seconds prior to gate motion.
External Alarm Reset Button Instantly resets the built-in safety alarm siren.

.......more details

OSH-6212-ECB-LH

Manaras Opera-SH 1/2 HP 240V 1Ph with Electronic Circuit Board Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"

Installation Manual

SETR2641AM2K

Erone 2-Channel Mini Transmitter Black 433MHz

Heavy-duty construction
Elegant & easy to carry
Unobstructed range: 656 ft (200m)
60 x 36 x 16mm (2.35 x 1.4 x 0.6in)
Two lithium batteries (CR2016) included

Wireless System Chart

GH-6533-0000-CBOX

Manaras Control Box for GH 600V

Control box only

2520-437-BT-YELLW

Linear Token Acceptor Yellow 12" x 10" Locked Outdoor Encloser

Available in Black White or Yellow
Stand not included

.375-6-R-C

Cut-to-Length Torsion Spring .375 x 6" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED

.343-334-R-C

Cut-to-Length Torsion Spring .343 x 3-3/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

.331-258-R-C

Cut-to-Length Torsion Spring .331 x 2-5/8" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.295-258-L-C

Cut-to-Length Torsion Spring .295 x 2-5/8" Left Hand Wound Coated ** Price by Quote Only

Priced per inch
For factory installed cones priced seperately - use part no. C-258-INSTALLED

.273-334-L-C

Cut-to-Length Torsion Spring .273 x 3-3/4" Left Hand Wound Coated ** Price by Quote Only

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

.273-258-R-C

Cut-to-Length Torsion Spring .273 x 2-5/8" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.218-134-R-C

Cut-to-Length Torsion Spring .218 x 1-3/4" Right Hand Wound Coated ** Price by Quote Only

Priced per inch - cones sold seperately
For factory installed cones use part no. C-134-INSTALLED

LMRT

LiftMaster Remote Test Plate

MOTOR273

Manaras Electric Motor 3/4HP 208/480V 3Ph

Continuous-duty base mount ODP 60Hz
This item is compatible with BRAKE011

LA412XL20W

LiftMaster Single Arm Solar Package for LA412DC XL Gate Operator UL325 ***Includes (1x) K94-37236 Solar Harness (1x) SP20W12V Solar Panel (1x) LMRRUL Photo Eye (1x) A12330SGLPK Battery (12V) (1x) LA412DC Actuator Arm (1x) XLSOLARCONTUL Control Box

Access your property like never before. With MyQ® Technology you can monitor and control your gate from anywhere and get in quickly and securely with the built-in interference eliminating Security+ 2.0® radio.
Heavy-Duty Cast Aluminum Housing DC Motor powerful enough to perform in the most demanding applications.
Soft start/stop operation extends operator and hardware life for heavy-duty gate use.
Gate Size rated for gates up to 16 ft. in length or weighing up to 850 lbs.
Includes: Single arm control box solar harness kit solar panel kit 12V 20W LMRRU photoeye and battery 12V 33 Ah.
Item codes: XLSOLARCONTUL SP20W12V LMRRUL LA412DC K94-37236 A12330SGLPK

.......more details

MG-00082

Micanan Plastic Spacer for Boards (Long Length 1.190)

MK-00666

Micanan RF Junction Connector for Antenna

MP-00077

Micanan Heavy Duty Front Idler (Trolley End Bracket) #41 w/Pillow Blocks

RB709U-NB

Linear GTO Garage Door Receiver Adapter Mighty Mule

The RB709 Garage Door Opener Adapter enables the Mighty Mule transmitters to open and close almost any garage door opener
Made to be used with the FM134 (two button) and the RB743 (three button) remote control transmitters or F310 Keypad
Easy to install with almost any garage door opener
One RB709 is needed for each garage door opener that will be controlled by the Mighty Mule transmitters

K001D8397-1

LiftMaster Power Board 3ph 575V L5

This is a 3PH/L5 Power Board 575V Replacement Kit. Compatible with various LiftMaster® 3 Phase Logic 5.0 Commercial Door Operators; equipped with current sense

MV-00019

Micanan Pull Cord SPST Lever Type - Nema 4

MV-00238

Micanan Key Switch O/C Tamper Proof w/Best Core Cylinder Nema 1 Flush Mount

SD105L5-LH

LiftMaster Heavy-Duty Slide Door Operator 1 HP 575V 3PH Left Hand (Must include hardware box)

Perfect for split and sliding doors involved with industrial applications.
It is installed above the door and corresponds with the direction the door will be traveling.
Comes equipped with an emergency disconnect and for manual lifting in an emergency and automatic reconnect.
The new logic 5 commercial operators come with MyQ Technology built in. * 828LM required
Built In Security+ 2.0 radio receiver
Solenoid brake included

.......more details

RA-HOIST

GDI RA Chain Hoist/Brake 'BCR' N4/Flr Levl Dscnct N4 Field Install

Can be added in the field

PRO-J-7543-U-RH

Micanan 3/4HP 460V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

42GRR-AB

Allen Bradley Thru-Beam Photocell RX/TX Long Range 42GRR9001+GRL9040

PRO-J-7581-U-LH

Micanan 3/4HP 208V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5021-U-LH

Micanan 1/2HP 230V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

TRACK-1458-SS

Track Bolt Stainless Steel 1/4" x 5/8"

.273-258-L

Cut-to-Length Torsion Spring .273 x 2-5/8" Left Hand Wound Orange/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

PRO-APT-7581-U

Micanan 3/4HP 208V 1P Apartment Trolley Operator N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board

PRO-T-7525-U

Micanan 3/4HP 220V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-T-5083-U

Micanan 1/2HP 208V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

1004-2-16'

Aluminum Bottom Retainer 2" U-Shape with Reinforcement 16 ft***Actual Length 16'2"***

For door thickness 2"

MOTOR271

Manaras Electric Motor1/2HP 208/460V 3PH

This item is compatible with BRAKE011

42GRR-9001

Allen Bradley Series 9000 Photoelectric Sensor Thru-Beam Receiver Unit

nput: 20-40VAC 10-55VDC 4VA

RELAY039

Manaras Relay 3-Pole 24VAC

K10-33850

LiftMaster E-Box Cover MH MJ MT

MS-00002

Micanan Trolley Track Set 12 Ga. 9'6" (for 7' h. door) Includes 2 Angles Only

Set includes 2 tracks only
Chain NOT included

212SE

Nortek Linear Weatherproof Keypad

120 users
Indoor/outdoor self contained brushed metal housing
Surface mount vandal resistant design
One piece housing suitable for wall post or gooseneck mounting
Durable metal Braille alpha-numeric keys
4 on board programmable timed relays

.......more details

MK-00055

Micanan Transformer 575V-24V-50VA

Fingersafe

E/BLOP/150

Automatic Systems Safety Edge for BL229 14'-9" (EABLOP/150)

TB410-36SF

Steel Faced Laminated Bumper Black 10" x 36" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB406-36SF

Steel Faced Laminated Bumper Black 6" x 36" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB412-36SF

Steel Faced Laminated Bumper Black 12" x 36" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB620-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LLB620-22SF

Steel Faced Laminated Bumper Black 6" Projection L-Shaped 20" x 22" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.

.......more details

LVB624-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 24" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LB610-18SF

Steel Faced Laminated Bumper Black 10" x 18" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB410-14

Laminated Bumper Standard Black 10" x 14" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

ME00010

Micanan Input Shaft PRO-J 3/4" x 11-9/16"

RESET014

Manaras Resettable Overload Fuse 17A 1 Phase

CP-SH-34-1712_SHAFT_ONLY

Lynx Clutch Shaft Only for HDC Operators

Fits all HDC operators - waterproof or not. All HP all years
3/4" x 17 1/2" - 2.15lbs

AIRSWITCH016

Fraba Air Wave Switch Only

Fraba air switch only

LA500XL20W

LiftMaster Single Arm Solar Package for LA500 Gate Operator UL325 (Include (2x) SP10W12V Solar Panels (1x) XLSOLARCONTUL Control Box (1x) K94-37236 Solar Harness (1x) LMRRUL Photoeye (1x) K10-36183 Battery Tray (2x) A12330SGLPK Batt. (1x) LA500DC)

Kit Includes: LA500DC arm XL Solar control box (XLSOLARCONTU) which includes two 10WATT 12V Solar panels compatible with LA400 LA412 and LA500 Universal Solar harness (K94-37236) Monitored Retro Reflective Photos Eyes (LMRRU) Battery Tray (K10-36183) and two batteies (A12330SGLPK)
For dual gates order extra LA500DCS secondary arm
Updated unit complies with new UL325 code revised Jan 2016
Commercial Duty Cast Aluminum Housing with Heavy-Duty DC Motor powerful enough to perform in the most demanding applications. Soft start/stop operation extends operator and hardware life for heavy-duty gate use.

Manuel d'installation Installation manual Sell Sheet Brochure

Z9211-2

Stationary Cone Tool 2-5/8"

Easily dislodges the cone from the torsion spring

Z9211-1

Stationary Cone Tool 1-3/4" & 2"

Easily dislodges the cone from the torsion spring

LVB620-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

PRO-PL-10053-E

Micanan Wall Mount Control Panel 1HP 575V Non-Monitored ECB

Standard features include: N-4/12 12" x 10" x 6" panel B-2 C-2 D1 E2 T TS Mid-stop control functions Time delay on reverse On-board radio receiver hinged cover backplate primary fuses in panel
If PBS on cover required an additional charge will apply
If panel not ordered with an operator an additional charge will apply

MX-00016

Micanan TEFC Motor Upgrade Modification

TEFC motor upgrade for 1-phase belt drive operators

H503L5-LH

LiftMaster Ind. Duty Hoist Op. 1/2 HP 208/230-460V VAC 3 Ph Logic 5 Left Hand

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details