Devanco Canada - Get The Right Garage Door Opener‎ and Parts

26-945215

Truck Door Intermediate Panel (11.5" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood. Primer finish

LB410-14SF/P1

Steel Faced Laminated Bumper Black 10" x 14" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LMEOLRES-10

LiftMaster End of Line Resistor 10K

For use with various LiftMaster® Commercial Fire Door Operators Gate Operators and Extended High Performance Release Devices

TDC48-14

LiftMaster Trolley Chain Pack #48 700LBS 14ft Door

Chain pack only
TDC48-14 is a #48 Chain Pack Kit for 14 Ft. Trolley Rail Assemblies.
For use with LiftMaster® MAXUM TDC 700 Series Standard-Duty Trolley Commercial Door Operators; installed on 14' commercial doors.

JHDC22X4BMC

LiftMaster MAXUM Jackshaft 1.5 HP Heavy Duty 480V 3PH 60 Cycles/Hour 2200LB

New DC high-efficiency motor and gearbox provides the power needed and smooth start and stop to reduce wear-and-tear on your door and operator
Average of 12” per second opening on sectional doors and 8-9” per second on rolling steel doors
Provides seamless operation by supplying standby power when the power is down (battery backup kit sold separately)
Listed to ANSI/CAN/UL325 Standard for USA/Canada
Drive Type 65:1 Gearbox with #50 Chain Output
Radio Receiver DC Logic 1.0 board with Security+ 2.0® rolling code technology remote controls and binary DIP switch remote controls

.......more details

CBG24DCGMC-GREY

LiftMaster Techna Commercial DC Barrier Gate Operator Grey Cabinet

24VDC barrier gate operator with battery backup
Continuous-duty motor with soft start/stop
Exceptional starting torque and continuous operation
Heavy-duty motor supports 6000 cycles per day
Operator speed of 2.5 seconds to open or close
Aluminum alloy chassis

.......more details

Installation Manual Sell Sheet Data Sheet Wiring Diagram Quick Start Quide

EP2983-BLACK

Exhaust Port 4" non latching long barrel Black Nylon

Inside diameter: 4"
Outide diameter: 4-3/8"
Sleeve: 2" (non latching)
Flange: 6"
Includes fasteners
Black Nylon

.......more details

IP-MONB

CDVI Interior Touch Screen Monitor for IP-MDS/IP-SDS Video Intercom System in Black

Interior 7" touch screen TFT monitor for use with the IP-MDS/IP-SDS intercom systems in black.
IP system connects through the PoE system and also has a free to download app available on iOS and Android. The VDP app allows for users to connect with visitors at the door station and can control the door locks remotely.
Also available in white: IP-MON
SIP Server
Operating temperature: -10C to 55C
Call recording and built-in memory

.......more details

CDJH-12-115-CONT

Lynx CDJH Heavy-Duty Jackshaft 1/2 HP 115V Contactor Model

Built-in 3-channel 372 Mhz radio receiver accepts up to 20 remotes
4L V-belt primary reduction #41 drive chain and sprockets.
Adjustable friction clutch Inherent Mechanical Brake included
Solenoid brake optional **
Fully driven adjustable limit switches.
Heavy duty 3 button wall station (Open Close Stop).

.......more details

LA400XL20W

LiftMaster Single Arm Solar Package for LA400 Gate Operator UL325 (Include (2x) SP10W12V Solar Panels (1x) XLSOLARCONTUL Control Box (1x) K94-37236 Solar Harness (1x) LMRRUL Photoeye (1x) K10-36183 Battery Tray (2x) A12330SGLPK Batt. (1x) LA400DC)

Kit Includes: LA400DC arm XL Solar control box (XLSOLARCONTU) which includes two 10WATT 12V Solar panels compatible with LA400 LA412 and LA500 Universal Solar harness (K94-37236) Monitored Retro Reflective Photos Eyes (LMRRU) Battery Tray (K10-36183) and two batteies (A12330SGLPK)
For dual gates order extra LA400DCS secondary arm
Updated unit complies with new UL325 code revised Jan 2016

LZR-H100

BEA LZR Gold-Black BLK-02 H100

Laser scanner for gate and barrier applications.
Provides four laser-based curtains offering a three dimensional detection zone.
Detection curtains are highly configurable and can be set up for activation and presence detection in vehicle sensing applications.
Effective alternative to induction loops.
Max detection range: 32'x32'
Cable length: 33'

.......more details

LZR-H100 User Guide (EN)LZR-H100 Cut Sheet (EN)LZR-H100 User Guide (FR)LZR-H100 Cut Sheet (FR)

5-38-10

2" Horizontal Track Set 8'6" (7ft Door) 10" Radius 16ga 2-pcs

Left/Right hand horizontal track set 10" radius
Garage Door Residential usage

BEA-10EAGLE-ARTEK

BEA Eagle Compact Motion Sensor 6'-13' Mounting Height

EAGLE ARTEK is a motion sensor for all types of automatic doors. Its slim and compact design ensures discreet integration for your application making it ideal for pedestrian doors.
Superior field performance with improved filters that help to reduce false detections.
Easy to install and set up with flexible parameters and simple push-button settings. •The detection field can be adjusted without manually adjusting the antenna.
Max. detection range: wide: 13’ × 6.5’ narrow : 6.5’ × 7’ (@ 7’ high)
Temperature range: -4 – 131 °F (-20 – 55 °C)
Cable length: 8’

.......more details

Installation manual Spec sheet

41832R.S

Genie Service Head 6070H/B 6170H/B

FOR REPLACEMENT OF JACKSHAFT OPERATOR SHAFT RELEASE OR MOTOR ASSEMBLIES
Head Service Kit for 6070H/6070HB and 6170H/6170HB
Special Order Price by Quote Only
This kit includes the complete motor but does not include the circuit boards transformer or cover for the 6070/6170 unit.

OTBH-6113-AM06

Manaras Apt-Style Trolley Op 3/4HP 120V 1Ph Monitored w/N1 Eyes Silencio

The Silencio operators have integrated noise reducing enhancements which make it 4X QUIETER than the Premium Trolley Apartment model (OTBH-A.05).
A low headroom apartment type garage door operator designed for use on industrial standard lift sectional doors with high cycling daily frequency requirements
Mounting (Low Headroom Design): Ceiling-mounted with only 6.25" headroom clearance required below the tracks. For indoor use only.
Dimensions: Back Room: door height + 4'5" (1350 mm)
Head Room For Tracks: 5.625" (143 mm) above the highest point of door travel

HSLG-411

Linear Commercial Slide Gate Operator 3/4 HP 115V 1 Ph - Heater not Included

Great for industrial and commercial applications
Features the APeX control board
Emergency manual disconnect handle
Powder coat finish
Post mount standard; pad mount optional
Integral entrapment sensing system with dual multi-turn precision potentiometers for accurate adjustment and enhanced safety

.......more details

BEARING007

Manaras Flange Bearing ID 1"

Flange bearing for 1" shaft

CB14-KOR-PER-FT

Cable 1/4" 7x19 Galvanized Supreme Sold per Foot

Galvanized Cable 1/4" 7x19.
Cable break strength: 2000 lbs
A higher quality cable compared to the Chinese cable.
Meets endurance test requirements of over 35000 work cycles
Lubricated for flexability and longer service life
Sold per foot anything over 2" is rounded up to the next foot.

.......more details

GDI-HB340

GDI Direct Drive & Jackshaft HAML-RBH-A830 Nema 4 To Accept 1" Shaft Non Monitored

Compact & Light Weight - Fast Installation
Applications Include Car Wash Cold Storage Pharmaceutical Agricultural Food Facility Sectional Grilles and Rolling Steel Doors
Brushless DC High Reliability Hi Efficiency & Low Maintenance Motor
No maintenance GearMotor sealed stainless steel bearings no limit switches no belts or hydraulic cylinders to maintain
One Operator Handles all AC Voltage Applications (115/208/230/460 & 575V)
Soft start soft stop

.......more details

P-831RE

Pulsar 1-Door O/C/S Receiver 318 MHZ P-110554

Allstar compatible
Economy housing receiver
OPEN-CLOSE-STOP
24V AC/DC
8 dipswitches 318 MHz

Wiring-diagram

PLA10

NICE Electric Gate Lock Vertical Mount 12V

Required for gates longer than 3m (9.84')
Vertical mounting
Possibility of manual opening
Power: 12V 15VA 50Hz

K32-11010

LiftMaster Gear Reducer 44:1 1-1/2-2 HP

Replacement Kit. Compatible with 1HP 1/2HP & 2HP LiftMaster® GH Model Commercial Door Operators
Also known as: 32-11010 3211010

1016-ADHSVE-CAULK

Adhesive for Storm Shield Caulk Tubes 10.3oz

For use with 1016

MRIN

LiftMaster Base Riser Mount for industrial operators

Works with LiftMaster IHSL24UL and INSL24UL slide gate operators
Provides a base-mount option instead of post-mounting the operators

Installation manual Manuel d'installation Retrofit guide Guide d'installation

LA412DC

LiftMaster replacement 12VDC Solar Actuator Arm

he LA412 Arm runs on 12V and connot be subbed for LA400 Arm

HAE00072

Linear WiFi Wall Station

This Wi-Fi wall station allows direct operation of the door operator and light using the buttons.
When connected to your local wireless access point you can check status get notifications open or close the door and manage user access from any location via the Linear Android or iOS app.
Requirements: To use with the app you will need:
a Wi-Fi network with internet connectivity
a strong Wi-Fi signal in the garage where you are installing the wall station
an Android or iOS smartphone or tablet

.......more details

Programming Instructions

210-0057

TNR Doors CurtainLok Kit HDXL9 5/Kit (10 pcs) ** Price by Quote Only

Natural UHMW-PE 5 Lok's
Sold as a kit of (5) complete loks that require 2 curtain loks and 2 screw (10) of each piece for 5 loks

RS-40

Roller Shutter Aluminum Model 40 Made to Order Pricing by Quote Only

The RS-40 is designed for use in window roller shutters door recesses and small shopfronts.
These profiles are of better technical performance and are thus more stable.
At the same time good coil diameters allow to use this profile in small-size boxes.
The foam filling ensures good heat and acoustic insulation.
Its low weight allows the use of manual drives spring- or electric control devices.
The RS-40 profile is available with or without perforation in a wide range of RAL-like colours.

.......more details

51115

Doorlec Fire Release System

For fire rated rolling service doors connecting to existing dropout fusible link device
For GH and Belt Drive operators

27026

Doorlec Electric Motor TEFC 1.5 HP 115/230V 1P DC203C

General purpose - Frame 56C
1725 RPM for worm-gear reducer models TEFC type

EXA-1000

Linear Omni-Directional Remote Antenna (AAE00198)

The EXA-1000 is a 1/2 wave center fed vertical antenna composed of three parts: an Antenna assembly with an F connector attachment; a Base Plate assembly with radial mounting provisions; and a five-foot 75-ohm coaxial cable.
The cable connects to the antenna base on one end and the receivers F connector on the other.
If the antenna must be mounted further than five feet from the receiver an extension cable of up to a maximum of 25 feet may be used instead of the five foot cable supplied.
Because of the cable resistance the performance of the EXA-1000 may be degraded by using longer than a 25 foot cable
Compatible with all Linear receivers with Type F antenna connector
Receives signals in 288 to 320 MHz range

.......more details

Installation manual

71-EB120

LiftMaster External Brake Solenoid 120V

Same as K71-EB120 71B120X

PC-3

EMX Infrared Modulated Photoeye Thru Beam

Thru beam configuration
LED alignment indicator simplifies installation
No calibration or sensitivity adjustments needed
Wide sensing angle for increased reliability
30 ft. operating range
Housing: Black PVC * Not water tight

.......more details

89493

Marantec RPM Sensor with Wire Harness

For use on M-line/Q-line/EOS models

E402-00-FM

Doorlec Ersce Utility Switch 6A/230V Roller Arm ** Indef. Delivery

Utility switch with a 'NO' and a 'NC' contact
Adjustable arm with roller
Made in Italy

684-33-110

Universal Bracket 2.25" x 2.5" x 48" w/ Plate 4"x12"

SGP-311-1-115/1

Doorlec Gate Master 1 HP 115V 1 Phase with Heater

Post mount heavy-duty industrial slide gate operator
Max. gate weight: 2500 lbs
Gate travelling speed: 45 ft / minute
175 watt heater with thermostat included
Includes Omron reflective photocell

CHC-SS-532

Chain Hoist Hand Chain Stainless Steel 5/32" Sold per Foot

Welded chain. Weldless chain is not available in stainless steel

MA034RDOT

LiftMaster Articulating Square PVC Arm Kit Red/White with Retro-Reflective DOT Tape 9 ft

For use on Mega-Arm gate operator
Red White reflective DOT stripe
9 ft. x 2.5 in. square includes hardware kit (MA033)

Additional arm accessories

746

Fasteners Ribbed Neck Track Bolt 5/16-18 x 3/4" Zinc 1000/box

111502.0002

Overhead Electric Motor RHX 3/4hp 115V Single Phase

TRANSF112

Manaras Transformer 575V-24V-50VA

CAP475

Capacitor 125VAC 475MFD

Motor Start Capacitor 125V 475 MFD

LV-24-TL-RG

Narrow Lights for Loading Docks Red / Green LED 12-24VAC/DC 24-3/8" long Sold Individually

LED lights offer long-lasting reliable high-visibility in all weather conditions including direct sunlight with low power consumption.
Robust housing resists impact and corrosion.
Slim discrete design ensures little risk of damage due to accidental impact.
Wide input voltage range of 12-24Vac/dc (control box available for alternate voltages).
Boards coated in water-resistant polymer for optimal protection from water and humidity.
24 LEDs per guide light (12 Red 12 Green)

.......more details

SM101

Miller Edge Signature Module for T3 Monitored Plugs w/ JB-03

Commercial signature module for use in commercial door and gate operators built after August 29 2010.
Engineered to emulate monitored pulse signal required by some commercial door operators.
LED light indicates device power or fault conditions.
Nema 4
Temperature range: -31F to 158F
5 to 40V DC

.......more details

PHOTO-070

Manaras Monitored Photoelectric Cells N1 Thru-Beam 45' Range

Monitored NEMA 1 enclosure through-beam type photocell
4-Wire
Indoor
Range: 45 ft

Manual

POWERHINGE

LiftMaster Power Hinge - All Steel Pair

Elite Power Hinge ball bearing hinges for steel swing gate (Pair)
Double 5/8 in. ball bearings for smooth operation
3/4 in. solid stainless steel shaft grounded and tempered to Rockwell standards
Continuous cycle operation self-lubricating/no grease fittings
Offers a unique design so the gate never hits the post
3000 lbs. per pair weight capacity

.......more details

ME-00009

Micanan Trolley Track Spreader Bar Assembly 1 Unit Only

3/4" x 5.79" long
2 are included when bought in the kit #MX-00119

ALUM-509

Aluminum 24" x 100' Spool Midnight Surf / Vagues de Minuit # 509

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 509
Reverse side is #431 Bright White

Colour chart

ALUM-265

Aluminum 24" x 100' Spool Antique Brown / Brun Antique # 265

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 265
White #431 on reverse side

Colour chart

PRO-APTB-5043-U

Micanan 1/2HP 460V 3P Apartment Trolley Operator With Brake N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-APT-5043-U

Micanan 1/2HP 460V 3P Apartment Trolley Operator N1 Eyes Monitored ECB (PRO APTE)

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

STEELCRAFT_PANEL_SEAL

Steelcraft Intermediate Section Seal V-Bead Sold by the Foot

3BLM

Exterior Control Station 3 Button N4 with Mortise Lockout in Metal Enclose

Open-Close-Stop
Dimensions: 7" h x 2-3/4" w x 3-1/2" d
Exterior surface mount

3BLM

620-101416

Linear GTO Alarm 24VDC Non-Pulsed Apex

PRO-HB-7511U-LH

Micanan 3/4HP 115V 1P Hoist Op. with Brake N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

MB-15204

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 145TC

Fits GT GH GHC & GSD

25C20

LiftMaster Screw Drive Coupling K025C0020

DOCK-SEAL

Special Order Dock Seal Price by Quote Only

Made to order Models R-100 R-600 & R-700
Standard Seals include two side pads with a fixed head pad and option for an adjustable head curtain.
40 Oz Vinyl
Comes with full height yellow guide strips and option for wear flaps
Black Blue and Green are stock colors for other colors there will be a surcharge as well as longer production time
Custom Logo available

.......more details

R-100 order form R-600 order form R-700 order form Catalogue

MGH-6537-ECB-RH

Manaras 3 HP 600V 3P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

F3100MBC

Linear Wireless Keypad with Intercom Estate Series *** Disc

Increased Surveillance: Screen visitors and solicitors safely from inside your home
Superior Range: Crystal clear two-way wireless communication up to 500 ft. (152.4 m) without any obstructions
Stand Alone Keypad: Program up to 100 entry codes for added security
Motion activated backlit keypad
Kit includes 1 base station with rechargeable battery

OCDFX1

Overhead Door 1-Btn Transmitter 315/390 Mhz

Dual Frequency transmitter that will work on all OHD/Genie brand 315 or 390 rolling code commercial openers including the the RX OHD commercial opener.
Part Number: OCDFX1.S GIDFX1.S

Programming Instructions

ETOOL

LiftMaster Edge Cutting Tool***NLA

PRO-GH-10053U-R

Micanan 1 HP 575V 3P Gearhead Op. N1 Eyes Monitored ECB Right Hand

Designed for use on all rolling doors and grilles and for large sectional doors with high or vertical lift.
Full function smart 10.0 logic board featuring on-board receiver with antenna and enhanced program selections.
External radio control terminal strip
Three button O/C/S control station Nema-1
Supplied with Nema-1 photocells
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

19051

Doorlec VBelt 5L370

works on model ETBX

K72-12509

LiftMaster Output Shaft Kit (3/4 & 1 HP)

For commercial operator model T
Complete with: Output Shaft Bearing Roller Chain with Master Link Limit Chain Shim Washers Roll Pins Push Ring 3/4' and Sprockets (41B32 & 48B10)

LB406-14

Laminated Bumper Standard Black 6" x 14" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LIMIT-KIT-BCSI

Limit Shaft Kit for BCSI Gate Operator ** Price by Quote Only

HSO112

Hinge 1/2-Hinge OHD "A" Style 12-ga Stainless Steel

Manufactured with Heavy Duty 12ga. Rust-Resistant 304 Stainless Steel
Laser Cut for a Clean Finish

XR-1

Linear Single Channel Mid-Range Receiver ** Discontinued

1-channel mid-range receiver
Up to 10 miles line-of-sight range (with XT-1 & XT-4)
Up to 2 miles of line-of-sight with handheld devices
Over 64 000 codes
Weather-resistant case
RF frequency; 27.255 MHz

.......more details

MV-00295

Micanan Fraba Nema 4/4X RAY-RT-HD with Reflector

Monitored Retroreflective photocell
Sensing distance: 50 ft
Includes bracket and long range reflector

VBELTB30

Manaras VBelt 5L 30" Type B (5L330)

For models OTH OTBH OSL
Same as 5L330

MU22-2WIRE-LH-G

Miller Edge MU22 2-Wire Left Hand Gray - Sold per Foot

��Electromechanical edge for sectional doors and aircraft hangars. •The MU22 is a custom edge manufactured to exact specifications. •The MU22 is completely flexible and will contour to curved surfaces. It's profile can also be square rectangular or angled. •Touch sensitive signaling allows immediate reversal or stopping of motion. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •Vertical or horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

LIMIT020

Manaras Unimax Snap-Action SPDT without Lever

Single limit switch (SPDT) used to stop the door at top and bottom or as disconnect switch
Unimax
Snap-action

37558R

Genie Belt Drive Sprocket Assembly

Complete assembly for the belt sprocket on top of the machine.
Works with the following models: IntelliG 1200 and IntelliG 1000

JDMG-LG-BBU

GDI Battery Backup Option G3243

Battery Backup option for JDMG-LG operator

MIRM-T2

Miller Edge Patriot 2 Photo Eye Monitored 30ft Non-Contact ** NLA

Attaches directly to a Sectional door.
The photo eyes travel below the door during the closing cycle.
Unlike traditional static mount photo eyes; Patriot travels with the door sensing obstructions prior to contact.
The Patriot2 non-contact system consists of thru beam photo optics.
Emitting and receiving eyes mount into a rigid steel spring loaded retracting housing.
The housings attach to the bottom section of the door and extend below the leading edge of the door providing an invisible infrared light beam of protection.

.......more details

TS150

Wayne Dalton Thermospan 150 Steel Panel

Polyurethane insulation R-Value*=14.16
Max Width 26’2”
1-3/8” Section Thickness
Patented roll-formed integral struts for rigidity
Stucco embossed exterior with pinstriping

HTRNB

LiftMaster Heater Kit for AC Pad Mount Gate Operators

Heater kit for pad mount AC gate operators.
Battery bracket NOT included.
Protects system to -40° F and installs on operator frame
Measurements: 6 x 2 3/8 x 3 3/8

PPLV1

LiftMaster Passport Lite 1-Button Visor Remote with Sec+ 2.0 Technology

Passport Lite Remote Controls provide cost-effective single button access solutions for gate access only or high-capacity commercial properties applications such as employee parking lots and tenant garages.
These remote controls are specifically designed for gate access control and are not compatible with LiftMaster Garage Door Openers.
2x the range of standard remote controls
Narrow-band transmission on 3 simultaneous frequencies (310 MHz 315 MHz 390 MHz)
Compatible with LiftMaster® commercial receivers (850LM 860LM PPWR STAR1000) and Security+ 2.0™ Gate Operators
Block coded

.......more details

Programming instructions Instructions de programmation Sell sheet Brochure

BK020/PR-BOLT

Commercial 2" Safety Bottom Bracket with Bolt Sold as a Pair

Maximum cable diameter: 3/16"
Maximum door weight: 1300 lbs Zinc
Plated Steel
Sold as a pair

Installation manual

98875

Marantec Shark Tooth Position Reference Tab Chain Rail

For chain rails.
This part is installed inside rail on the actual chain.
This part works with the reference switch to determine the open & close limits of the garage door.
Reference switch part # 104083

ME123-M-BLK-U

Miller Edge Black Universal 4 -Wire Monitored 2" wide x 1-1/2" high Sold by the Foot

Electromechanical slide in edge for sectional doors and sliding gates.
Touch sensitive singaling allows for immediate stopping and reversing of motion
Temperature range: -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Worksheet Installation manual Sell sheet

Z9207

Sensor Guards Sold as a Pair

Made to fit over garage door sensors
Will fit over most popular sensor brands
Protects sensors from coming out of alignment
Helps protect against water corrosion
Easily installs to the door track or the the wood door frame
Sold by the pair

.......more details

21-7115-1

LiftMaster Transformer 115/230V 1Ph

20001

Doorlec Brake Spring

Fits LJ/LJH

PRO-APTB-5011-R

Micanan 1/2HP 115V 1P Apartment Trolley Operator With Brake Contactor

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

Installation manual Specification sheet

MUSHROOM-PB

Lockable Mushroom Push Button with 1 NC Contact

N/C Contact "Stop"
Push to Stop Turn to Unlock
NEMA 4 Enclosure

PS241F

Adjustable Regulated Power Supply with Optional BBU 6-24VDC 1AMP

3 preset voltages: 6 12 and 24 VDC
Full adjustment from 2 to 24 VDC if required
Requires AC transformer for input power (minimum 14 VAC for 12 VDC output 26 VAC for 24 VDC output cannot be connected directly to 120 VAC)
Maximum 1 amp. Output at 70 deg. F and free air
Ripple: Minimum load: 0.007vrms Half load: 0.028vrms Maximum load: 0.057vrms
Regulation: 97.5%

.......more details

Wiring Diagram Diagramme de raccordement Spec Sheet Spécifications

ST-CLEAR-TUBE

Soft Touch Clear Tubing Sold per Foot

ZT36640159

Rolling Steel Door Model 702 Firestar No 2 Slat 22-Ga

25-60502

Truck Door T-Style Ramp Handles Roadside (Left)

Black plastic construction
Cross ref.: 39504-1

CP-LX100

Lynx Control Board with Cover for UL325 models

For all voltages

Programming instructions

1001-18-BLACK

Commercial Side & Top Weather-Strip 18' Long - Black

Aluminum retainer with black dual-fin vinyl

1104-ASFT-24FT

Elton Aluminum Stiffener for 1104 24ft

Prevents the 1104 from buckling in the hot sun

MD-00030

Roller Chain #40 10' per Pack

Includes (1x) master link

50150

Doorlec Electro-Mechanical Safety Edge Sold per Foot *** Quote Required

For the protection of vehicles doors and safety of people.
Any upward-acting door may be fitted at the leading edge with an electro-mechanical safety weatherstrip.
This mechanism consists of a formed galvanized steel section covered with vinyl impregnated rubber hinged along the full width of the leading door edge.
Can be adjusted to approximately 2½" (63.5mm) to form a tight weather seal.
The hinge linkage is arranged that minimum pressure is required to activate the electrical control switch causing door to reverse direction of travel to the fully open position.
Reverse switch is enclosed in a galvanized housing with a sliding plunger to assure positive actuation every time.

.......more details

CABLE-NR-18-SS

Cable No Roll 1/8" 19x7 Stainless Steel T302-04 500ft

19X7 SS T302 1/8” Rotation-Resistant Wire Rope was conceived for overhead cranes but manufactured specifically for high-performance garage doors.
A spin-resistant construction coupled with the corrosion-resistance of stainless steel is the perfect mix of resilience and performance for high-traffic areas.
Minimum break strength of 1700lbs